ISO 128-33:2018
(Main)Technical product documentation (TPD) — General principles of presentation — Part 33: Representation of views, sections and cuts in construction drawings
Technical product documentation (TPD) — General principles of presentation — Part 33: Representation of views, sections and cuts in construction drawings
ISO 128-33:2018 lays down general rules for marking, designation, placing and orientation of views, sections and cuts, and the position of text in relation to figures on construction drawings. For all general rules, reference is made to the relevant parts of the ISO 128 series. As regards relative positions of views, the method using reference arrows according to ISO 128‑30 is used.
Documentation technique de produits (TPD) — Principes généraux de représentation — Partie 33: Représentation des vues, des sections et des coupes dans les dessins de construction
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 128-33
First edition
2018-02
Technical product documentation
(TPD) — General principles of
presentation —
Part 33:
Representation of views, sections and
cuts in construction drawings
Documentation technique de produits (TPD) — Principes généraux de
représentation —
Partie 33: Représentation des vues, des sections et des coupes dans les
dessins de construction
Reference number
ISO 128-33:2018(E)
©
ISO 2018
---------------------- Page: 1 ----------------------
ISO 128-33:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 128-33:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Marking of views, sections and cuts . 1
5 Designation . 2
6 Position and orientation . 4
7 Position of text in relation to figures . 5
Bibliography . 8
© ISO 2018 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 128-33:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html
This document was prepared by Technical Committee ISO/TC 10 Technical product documentation, SC 8
Construction documentation.
This first edition cancels and replaces the first edition of ISO 8048:1984, to be included in the ISO 128
series after renumbering. The revision includes the renaming of Clause 2 as normative references, an
update of references in the document, an additional Clause 3 for terms and definitions and an additional
bibliography.
iv © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 128-33:2018(E)
Technical product documentation (TPD) — General
principles of presentation —
Part 33:
Representation of views, sections and cuts in construction
drawings
1 Scope
This document lays down general rules for marking, designation, placing and orientation of views,
sections and cuts, and the position of text in relation to figures on construction drawings.
For all general rules, reference is made to the relevant parts of the ISO 128 series. As regards relative
positions of views, the method using reference arrows according to ISO 128-30 is used.
2 Normative references
The following documents are referred
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.