ISO 16079-1:2017

Condition monitoring and diagnostics of wind turbines — Part 1: General guidelines

ISO 16079-1:2017 gives guidelines which provide the basis for choosing condition monitoring methods used for failure mode detection, diagnostics and prognostics of wind power plant components.

Surveillance et diagnostic d'état des éoliennes de production d'électricité — Partie 1: Lignes directrices générales

L'ISO 16079-1 :2017 fournit des lignes directrices qui servent de base pour choisir les méthodes de surveillance d'état utilisées pour la détection des modes de défaillance, le diagnostic et le pronostic des composants des centrales éoliennes.

General Information

• Status: Published
• Publication Date: 02-Nov-2017
• ICS: 27.180 - Wind turbine energy systems
• Technical Committee: ISO/TC 108/SC 5 - Condition monitoring and diagnostics of machine systems
• Drafting Committee: ISO/TC 108/SC 5/WG 16 - Condition monitoring and diagnostics of wind turbines
• Current Stage: 9092 - International Standard to be revised
• Completion Date: 01-Nov-2023

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 16079-1
First edition
2017-11
Condition monitoring and diagnostics
of wind turbines —
Part 1:
General guidelines
Surveillance et diagnostic d'état des éoliennes de production
d'électricité —
Partie 1: Lignes directrices générales
Reference number
ISO 16079-1:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 16079-1:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16079-1:2017(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Overview of condition monitoring procedure implementation — Set-up and
diagnostics requirements . 3
5 FMECA: Identification of failure modes, their effects and criticality .6
5.1 Overview . 6
5.2 Identification of wind turbine components criticality factor, f . 7
CR
5.3 Identification of failure mode priority factor, f . 9
FMP
5.4 Calculating the monitoring priority number, n .10
MP
Annex A (informative) P-F interval, ETTF and RUL .12
Annex B (informative) Example of FMECA analysis for a wind turbine drive train .15
Annex C (informative) List of wind turbine components and their failure modes .18
Annex D (informative) Brief introduction to the concept of FMECA analysis .21
Bibliography .23
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 16079-1:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further mainten
...

ISO/TC 108/SC 5
Deleted: 2016-09-29
Date: 2017-10
Deleted: /DIS
ISO 16079-1:2017(E)
Deleted: 2016
ISO/TC 108/SC 5/WG
Secretariat: SA
Condition monitoring and diagnostics of wind turbines —
Part 1: General guidelines
Surveillance et diagnostic d'état des éoliennes de production d'électricité —
Partie 1: Lignes directrices générales
© ISO 2017 – All rights reserved
i

---------------------- Page: 1 ----------------------
ISO 16079-1:2017(E)
Contents
Foreword .iii
Introduction . iv
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Overview of condition monitoring procedure implementation — Set-up and
diagnostics requirements . 4
5  FMECA: Identification of failure modes, their effects and criticality . 7
5.1  Overview . 7
5.2  Identification of wind turbine components criticality factor, f . 8
CR
5.3  Identification of failure mode priority factor, f . 10
FMP
5.4  Calculating the monitoring priority number, nMP . 12
Annex A (informative) P-F interval, ETTF and RUL . 13
Annex B (informative) Example of FMECA analysis for a wind turbine drive train . 15
Annex C (informative) List of wind turbine components and their failure modes . 19
Annex D (informative) Brief introduction to the concept of FMECA analysis . 23
Bibliography . 25

© ISO 2017 – All rights reserved
ii

---------------------- Page: 2 ----------------------
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national
standards bodies (ISO member bodies). The work of preparing International Standards is normally
carried out through ISO technical committees. Each member body interested in a subject for which a
technical committee has been established has the right to be represented on that committee.
International organizations, governmental and non‐governmental, in liaison with ISO, also take part in
the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 108, Mechanical vibration, shock and
conditio
...

NORME ISO
INTERNATIONALE 16079-1
Première édition
2017-11
Surveillance et diagnostic d'état
des éoliennes de production
d'électricité —
Partie 1:
Lignes directrices générales
Condition monitoring and diagnostics of wind turbines —
Part 1: General guidelines
Numéro de référence
ISO 16079-1:2017(F)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 16079-1:2017(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Publié en Suisse
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 16079-1:2017(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Aperçu de la mise en œuvre d’une procédure de surveillance d’état — Exigences
relatives à la préparation et au diagnostic . 4
5 AMDEC: Identification des modes de défaillance, de leurs effets et de leur criticité .6
5.1 Aperçu général . 6
5.2 Détermination du facteur de criticité, f , des composants de l’éolienne . 8
FC
5.3 Détermination du facteur de priorité du mode de défaillance, f .
PMD 9
5.4 Calcul de l’ordre de priorité de la surveillance, n .
OPS 11
Annexe A (informative) Intervalle P-F, DEFAD et DVUR .12
Annexe B (informative) Exemple d’analyse AMDEC de la transmission d’une éolienne.15
Annexe C (informative) Liste des composants d’une éolienne et de leurs modes de défaillance .18
Annexe D (informative) Brève présentation du concept d’analyse AMDEC .21
Bibliographie .23
© ISO 2017 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 16079-1:2017(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre
...