Abstract

This document provides the design content and technical specification for the scheme of the multi-component thermal flooding development plan, which is applicable to onshore and offshore heavy oil reservoirs.

Status
Published
Publication Date
19-Nov-2026
Technical Committee
SC 10 - ISO/TC 67/SC 10
Drafting Committee
SC 10 - ISO/TC 67/SC 10
Current Stage
6060 - International Standard published
Start Date
20-Nov-2026
Completion Date
20-Nov-2026

Buy Documents

Technical specification

ISO/TS 25375:2026 - Oil and gas industries including lower carbon energy — Multi-component for thermal recovery — Flooding development plan design

Release Date:20-Nov-2026
English language (12 pages)
sale 15% off
Preview
sale 15% off
Preview

ISO/TS 25375:2026 is an ISO Technical Specification on oil and gas industries including lower carbon energy - multi-component thermal flooding development plan design. It sets out the design content and technical specification for multi-component thermal flooding schemes for onshore and offshore heavy oil reservoirs, so reservoir engineers, planners, and operators have a common framework for selecting reservoirs, designing fluids, and planning injection and monitoring.

What does ISO/TS 25375:2026 specify?

ISO/TS 25375:2026 specifies how to prepare a multi-component thermal flooding development plan for heavy oil reservoirs. It covers reservoir screening, reservoir performance evaluation, thermal fluid design, reservoir engineering design, and implementation monitoring.

The document is organized into:

  • Clause 1 Scope
  • Clause 2 Normative references
  • Clause 3 Terms and definitions
  • Clause 4 Reservoir characterization
  • Clause 5 Reservoir performance
  • Clause 6 Multi-component thermal fluids design
  • Clause 7 Specification for reservoir engineering design
  • Annex A, an informative example of data monitoring

Annex A supports field use by showing how injection-well and production-well data can be recorded during operation.

What are the key requirements of ISO/TS 25375:2026?

ISO/TS 25375:2026 requires a reservoir-by-reservoir design approach. The plan starts with geology, moves through performance review, and ends with injection, well-pattern, and monitoring decisions.

Reservoir characterization and screening

Clause 4 requires the design to be built on stratigraphic, structural, petrophysical, and fluid-property characterization. It also requires 3D geological models - structural, stratigraphic, facies, and property models - and says reserve estimation should be calculated from those models.

Clause 4.7 sets screening principles for applicability. The reservoir should be checked against crude oil properties, depth, thickness, net-to-gross thickness, permeability, porosity, oil saturation, aquifer size ratio, and formation pressure. The document also states that reservoir pressure should be below 10 MPa before multi-component thermal flooding, and that very viscous, shallow reservoirs with fewer interlayers may be better suited to SAGD or VAPEX.

Fluid selection and proportion design

Clause 6 requires the multi-component thermal fluids to combine heat, chemical agents, and gases. The selection must be optimized to the reservoir fluid distribution and the temperature-pressure conditions after steam huff and puff, using laboratory testing and reservoir numerical simulation.

The document gives practical selection rules for:

  • high-temperature thermal medium, with steam preferred and a minimum steam quality of 50%
  • chemical enhancement systems for viscosity reduction, oil displacement, foaming, or profile control
  • gases such as nitrogen, carbon dioxide, flue gas, and light hydrocarbons
  • injected gas oxygen content, which should be less than 1%

Clause 6 also links reservoir type to component proportion and target recovery improvement in Table 4. For users, that means the fluid recipe is not fixed - it must match the reservoir category and the development objective.

Engineering design and implementation

Clause 7 requires the plan to be economically and technically justified. It covers oilfield overview data, economic limits, well-pattern optimization, well spacing, timing of conversion, timing of chemical injection, and channelling prevention.

The document gives practical design directions such as:

  • preferring vertical wells over horizontal wells for injection and production to help control steam channelling
  • optimizing well spacing and conversion timing using recovery efficiency and economic benefit
  • using stratified steam injection where interlayers are thicker than 3 m
  • setting the bottom-hole steam quality at not less than 50%
  • defining clear quality control for chemical agents and requiring injected fluids to be free from organic chlorides

Monitoring and evaluation

Clause 5 requires performance evaluation through production history, current development status, reserve analysis, energy analysis, inter-well thermal connectivity analysis, and recoverable reserve evaluation. Clause 7.3.3.5 requires monitoring temperature, pressure, steam quality, tracers, chemical quality, produced water salinity, fluid properties, and H2S content in produced gas.

What terms does ISO/TS 25375:2026 define?

  • Multi-component thermal fluids (MCTF) - a high-temperature binary or ternary system made up of steam, hot water, gases, and chemical agents for improving oil recovery in heavy oil fields.
  • Steam injection rate - the quantity of steam injected into the well per day.
  • Gas injection rate - the quantity of gas injected into the well per day.
  • Production-injection ratio - the ratio of liquid production rate to steam injection rate in the block during the flooding process.
  • Gas-liquid ratio (GLR) - the ratio of gas volume to liquid volume under operating conditions.
  • Steam-oil ratio (SOR) - the volume ratio of crude oil produced to water-equivalent steam injected.
  • Chemical slug - a discrete volume of chemical solution injected separately to form a displacement zone in the reservoir.
  • Well pattern - the arrangement and distribution of production wells and injection wells in field development.

Who uses ISO/TS 25375:2026?

ISO/TS 25375:2026 is used by reservoir engineers, thermal recovery planners, production engineers, geologists, and oilfield development teams working on heavy oil projects. It is also relevant to international oil companies and service suppliers involved in heavy oil thermal recovery technical services.

In practice, users apply it to:

  • screen candidate reservoirs
  • design the multi-component thermal fluid system
  • choose well patterns and spacing
  • set injection and production targets
  • plan monitoring and field data collection
  • evaluate performance during steam huff and puff conversion and later flooding

Which standards are used with ISO/TS 25375:2026?

ISO/TS 25375:2026 cites several standards and related documents for supporting definitions and methods:

  • ISO 22475-1 - background on sampling and groundwater measurements, used for reservoir parameter context
  • ISO 18335 - supports viscosity-related calculations referenced for reservoir screening
  • ISO 1998-2 - provides petroleum terminology for API gravity and dynamic viscosity
  • ISO/TS 26762:2025 - gives a different GLR definition, which the document notes for comparison
  • ISO 696 - supports foaming power measurement for chemical-agent evaluation
  • ISO 862 - provides surfactant vocabulary used in the chemical-system section
  • ISO 15156-1 - supports material selection for H2S-containing environments
  • ISO 45001 - supports occupational health and safety requirements for steam, nitrogen, and chemical injection activities

What does the ISO/TS 25375:2026 document contain?

ISO/TS 25375:2026 contains design guidance, selection principles, and planning methods rather than worked examples of calculations. It includes Table 1 for applicable reservoir categories, Table 2 and Table 3 for chemical performance recommendations, and Table 4 for fluid proportion guidance by reservoir type.

The document also includes a monitoring annex. Annex A gives example data sheets for injection wells and production wells, including temperature, pressure, steam quality, chemical concentration, gas concentration, and tracer monitoring.

Across the main clauses, the document uses screening rules, optimization methods, and reservoir engineering calculations for design, testing, and field implementation. It is structured to help users move from reservoir description to fluid selection, then to well-pattern design and operational monitoring.

Buy Documents

Technical specification

ISO/TS 25375:2026 - Oil and gas industries including lower carbon energy — Multi-component for thermal recovery — Flooding development plan design

Release Date:20-Nov-2026
English language (12 pages)
sale 15% off
Preview
sale 15% off
Preview

Get Certified

Connect with accredited certification bodies for this standard

Element Materials Technology

Materials testing and product certification.

UKAS United Kingdom Verified

ABS Group Brazil

ABS Group certification services in Brazil.

CGCRE Brazil Verified

ABS Quality Evaluations Inc.

American Bureau of Shipping quality certification.

ANAB United States Verified

Sponsored listings

Frequently Asked Questions

ISO/TS 25375:2026 is a technical specification published by the International Organization for Standardization (ISO). Its full title is "Oil and gas industries including lower carbon energy — Multi-component for thermal recovery — Flooding development plan design". This standard covers: This document provides the design content and technical specification for the scheme of the multi-component thermal flooding development plan, which is applicable to onshore and offshore heavy oil reservoirs.

This document provides the design content and technical specification for the scheme of the multi-component thermal flooding development plan, which is applicable to onshore and offshore heavy oil reservoirs.

ISO/TS 25375:2026 is classified under the following ICS (International Classification for Standards) categories: 75.020 - Extraction and processing of petroleum and natural gas. The ICS classification helps identify the subject area and facilitates finding related standards.

ISO/TS 25375:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


Technical
Specification
ISO/TS 25375
First edition
Oil and gas industries including
2026-11
lower carbon energy — Multi-
component for thermal recovery —
Flooding development plan design
Industries du pétrole et du gaz, y compris les énergies à faible
teneur en carbone — Multi-composants pour la récupération
thermique — Elaboration de la stratégie d’injection
Reference number
© ISO 2026
All rights reserved.
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
an ISO member body, or an authorized third-party distributor.
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
photocopying, scanning, recording, or posting on internal or external digital platforms.
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Reservoir characterization . 2
4.1 Stratigraphic characteristics .2
4.2 Structural characteristics .2
4.3 Reservoir characteristics and heterogeneity .2
4.3.1 Reservoir characteristics .2
4.3.2 Reservoir heterogeneity .2
4.4 Fluids properties and temperature-pressure systems .2
4.5 Oil reservoir characteristics .3
4.6 3D geological models.3
4.7 Applicable reservoirs for multi-component thermal flooding .3
5 Reservoir performance . . 3
5.1 Production history .3
5.2 Current development status .4
5.3 Reservoir performance evaluation . . .4
5.3.1 Produced reserve analysis .4
5.3.2 Reservoir energy analysis .4
5.3.3 Inter-well thermal connectivity analysis .4
5.3.4 Reservoir performance analysis .4
5.3.5 Recoverable reserve evaluation.4
6 Multi-component thermal fluids design . 4
6.1 Components selection .4
6.1.1 Selection principles .4
6.1.2 High-temperature thermal medium .5
6.1.3 Chemical enhancement system .5
6.1.4 Gases.5
6.1.5 Optimization of multi-component thermal fluids proportion .6
6.2 Dosage design of multi-component thermal fluids .7
7 Specification for reservoir engineering design . 7
7.1 Development principles .7
7.2 Oilfield overview . .7
7.2.1 General .7
7.2.2 Exploration history .7
7.2.3 Development overview .7
7.3 Reservoir engineering design .7
7.3.1 Economic and technical limits .7
7.3.2 Injection-production parameter optimization .8
7.3.3 Reservoir engineering development design .8
Annex A (informative) Example of data monitoring .11
Bibliography .12

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee TC 67, Oil and gas industries including lower carbon
energy, Subcommittee SC 10, Enhanced oil recovery.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
Introduction
This document, developed by users and suppliers of the multi-component thermal flooding technology, is
intended to provide efficient and low-carbon emission recovery of heavy oil reservoirs worldwide.
The multi-component thermal flooding technology is an enhanced oil recovery (EOR) method for heavy
oil reservoirs, boasting advantages of production enhancement, efficiency improvement and low-carbon
characteristics. Leveraging the synergistic effects of heat, chemical agents, and gases, this technology
could solve the problems in steam flooding processes, including difficulties in steam chamber expansion,
displacement imbalance, and excessive heat loss, thereby effectively enhancing oil recovery in heavy oil
reservoirs.
Due to the significant differences in the characteristics of buried depth, oil viscosity and pressure of heavy oil
reservoirs in different oil regions, the multi-component thermal fluids and displacement methods employed
are not identical. This leads to notable differences in reservoir applicability and production enhancement
effect of the multi-component thermal flooding technology across different oilfields. The international
unified technical standard and specification have not been established, which limits the application and
popularization of this technology across world.
This document gives relatively universal technical specifications for the multi-component thermal flooding
development technology. It can assist international oil companies in carrying out heavy oil thermal recovery
technical services.
v
Technical Specification ISO/TS 25375:2026(en)
Oil and gas industries including lower carbon energy — Multi-
component for thermal recovery — Flooding development
plan design
1 Scope
This document provides the design content and technical specification for the scheme of the multi-component
thermal flooding development plan, which is applicable to onshore and offshore heavy oil reservoirs.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1
multi-component thermal fluids
MCTF
high temperature binary or ternary system composed of steam, hot water, gases and chemical agents, used
to improve oil recovery in heavy oil fields
Note 1 to entry: Gas components can include N , CO , CH , flue gas, etc.
2 2 4
3.2
steam injection rate
quantity of steam injected into the well per day
3.3
gas injection rate
quantity of gas injected into the well per day
3.4
production-injection ratio
ratio of the liquid production rate to the steam injection rate (3.2) in the block during the multi-component
thermal flooding process
3.5
gas-liquid ratio
GLR
ratio of gas volume to liquid volume under operating conditions
Note 1 to entry: GLR (3.5) is generally measured in standard units, e.g. cubic meters per cubic meter.
[1]
Note 2 to entry: GLR (3.5) in ISO/TS 26762:2025 is defined as ratio of produced gas flow rate to the produced total
liquid flow rate, which uses measures of produced gas/liquid and is different from the GLR (3.5) in this document.

3.6
steam-oil ratio
SOR
volume ratio of crude oil produced to water-equivalent steam injected
3.7
chemical slug
discrete volume of chemical solution injected separately into the injection well to form a displacement zone
in the reservoir
3.8
timing for thermal flooding conversion
conditions for converting the steam huff and puff to the multi-component thermal fluids (3.1)
3.9
well pattern
arrangement and distribution pattern of production wells and injection wells in oil and gas field development
3.10
well spacing
horizontal distance between injection wells and production wells
3.11
aquifer size ratio
ratio of water-filled pore volume to hydrocarbon-filled pore volume
4 Reservoir characterization
4.1 Stratigraphic characteristics
Stratigraphic characteristics should include stratigraphic sequence, detailed stratigraphic subdivision and
correlation.
4.2 Structural characteristics
Structural characteristics should include fault system and structural morphology.
4.3 Reservoir characteristics and heterogeneity
4.3.1 Reservoir characteristics
It should include reservoir petrology, sedimentary facies, physical properties, reservoir spatial distribution,
microscopic pore structure, reservoir sensitivity, and wettability characteristics.
4.3.2 Reservoir heterogeneity
The following information should be provided:
a) the intralayer, interlayer, and planar heterogeneity;
b) the lithology, occurrence, thickness, permeability, and distribution of interlayers;
c) the sand body coordination number, connectivity, connectivity coefficient, and size of connected sand
bodies.
4.4 Fluids properties and temperature-pressure systems
It should include fluids properties, geothermal gradient, and pressure coefficient.

4.5 Oil reservoir characteristics
It should include electrical property criteria for oil-water identification, oil-water contact determination, oil-
water distribution, and oil reservoir type.
4.6 3D geological models
Structural model, stratigraphic model, facies model, and property model should be built. The reserve
estimation should be calculated based on these models.
4.7 Applicable reservoirs for multi-component thermal flooding
The applicable reservoirs should be analysed by following principles:
a) the applicable reservoirs should be screened according to parameters such as crude oil
...