ISO 15830-2:2022

Road vehicles — Design and performance specifications for the WorldSID 50th percentile male side-impact dummy — Part 2: Mechanical subsystems

This document specifies requirements for mechanical components, specifications and validation tests for the WorldSID 50th percentile side-impact dummy, a standardized anthropomorphic dummy for near-side-impact tests of road vehicles.

Véhicules routiers — Conception et spécifications de performance pour le mannequin mondial (WorldSID), 50e percentile homme, de choc latéral — Partie 2: Sous-systèmes mécaniques

General Information

• Status: Published
• Publication Date: 15-Dec-2022
• ICS: 43.020 - Road vehicles in general
• Technical Committee: ISO/TC 22/SC 36 - Safety and impact testing
• Drafting Committee: ISO/TC 22/SC 36/WG 5 - Anthropomorphic test devices
• Current Stage: 6060 - International Standard published
• Start Date: 16-Dec-2022
• Due Date: 10-Jul-2022
• Completion Date: 16-Dec-2022

Relations

• Revises: ISO 15830-2:2013 - Road vehicles — Design and performance specifications for the WorldSID 50th percentile male side-impact dummy — Part 2: Mechanical subsystems
• Effective Date: 23-Apr-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 15830-2
Third edition
2022-12
Road vehicles — Design and
performance specifications for the
WorldSID 50th percentile male side-
impact dummy —
Part 2:
Mechanical subsystems
Véhicules routiers — Conception et spécifications de performance
pour le mannequin mondial (WorldSID), 50e percentile homme, de
choc latéral —
Partie 2: Sous-systèmes mécaniques
Reference number
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Mechanical requirements for WorldSID . 2
4.1 Head . 2
4.1.1 General description . . 2
4.1.2 Specifications . 2
4.1.3 Validation . 3
4.2 Neck . 3
4.2.1 General description . 3
4.2.2 Specifications . 3
4.2.3 Validation . 3
4.3 Thorax/abdomen/shoulder . 4
4.3.1 General description . 4
4.3.2 Specifications . 4
4.3.3 Validation . 4
4.4 Arms . . 5
4.4.1 General description . 5
4.4.2 Specifications . 5
4.5 Lumbar spine and pelvis . 6
4.5.1 General description . . 6
4.5.2 Specifications . 6
4.5.3 Validation . 6
4.6 Upper legs and knees . 6
4.6.1 General description . . 6
4.6.2 Specifications . 6
4.7 Lower legs, ankles, and feet . 6
4.7.1 General description . . 6
4.7.2 Specifications . 7
4.8 Clothing . 7
4.8.1 General description . 7
4.8.2 Specifications . 7
4.9 Whole dummy . 7
4.9.1 General description . 7
4.9.2 Specifications . 7
4.9.3 Validation . 8
5 Validation test procedures .10
5.1 Head . 10
5.1.1 Principle . 10
5.1.2 Apparatus . 10
5.1.3 Sensors . 10
5.1.4 Preparation . 10
5.1.5 Procedure . 12
5.1.6 Calculation procedures and expression of results .13
5.1.7 Test reports .13
5.2 Neck .13
5.2.1 Lateral flexion . 13
5.2.2 Torsion . 17
5.3 Thorax/abdomen/shoulder/pelvis full body tests . 20
5.3.1 Full body test setup . 20
iii
5.3.2 Shoulder test . 24
5.3.3 Thorax test . 26
5.3.4 Abdomen test .28
5.3.5 Pelvis test . 31
5.4 Whole body dimensions . 33
5.4.1 Principle . 33
5.4.2 Apparatus . 33
Annex A (informative) Optional WorldSID whole body dimension measurement procedure
with mechanical tools . 44
Annex B (informative) Single rib test .47
iv
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this docume
...