iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 18437-3:2005/Amd 1:2010

(Amendment)

Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method — Amendment 1

Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method — Amendment 1

Vibrations et chocs mécaniques — Caractérisation des propriétés mécaniques dynamiques des matériaux visco-élastiques — Partie 3: Méthode du faisceau par cisaillement en encorbellement — Amendement 1

General Information

Status
Published
Publication Date
15-Sep-2010
ICS
17.160 - Vibrations, shock and vibration measurements
Technical Committee
ISO/TC 108 - Mechanical vibration, shock and condition monitoring
Drafting Committee
ISO/TC 108/WG 28 - Vibration materials
Current Stage
6060 - International Standard published
Due Date
07-Nov-2010
Completion Date
16-Sep-2010
Ref Project

Relations

Amends
ISO 18437-3:2005 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method
Effective Date
11-Dec-2021

Buy Standard

ISO 18437-3:2005/Amd 1:2010ISO 18437-3:2005/Amd 1:2010
PreviousNext
Standard
ISO 18437-3:2005/Amd 1:2010
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 18437-3
First edition
2005-04-15
AMENDMENT 1
2010-09-15

Mechanical vibration and shock —
Characterization of the dynamic
mechanical properties of visco-elastic
materials —
Part 3:
Cantilever shear beam method
AMENDMENT 1
Vibrations et chocs mécaniques — Caractérisation des propriétés
mécaniques dynamiques des matériaux visco-élastiques —
Partie 3: Méthode du faisceau par cisaillement en encorbellement
AMENDEMENT 1




Reference number
ISO 18437-3:2005/Amd.1:2010(E)
©
ISO 2010

---------------------- Page: 1 ----------------------
ISO 18437-3:2005/Amd.1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 18437-3:2005/Amd.1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 5348:2021(Main)
Mechanical vibration and shock — Mechanical mounting of accelerometers

This document specifies the important technical properties of the different methods for mounting vibration transducers and describes recommended practices. It also shows examples of how accelerometer mounting can influence frequency response and gives examples of how other influences can affect the fidelity of the representation of actual motion in the structure being observed. This document applies to the contacting type of accelerometer which is currently in wide use. It is applicable to both uniaxial and multi-axial transducers. This document can also be applied to velocity transducers. This document enables the user to estimate the limitations of a mounting and consequent potential measurement deviations. Transducer mounting issues are not the only problem that can affect the validity of acceleration measurement. Other such problems include, amongst others: transverse movements, alignment of the transducer, base bending, cable movement, temperature changes, electric and magnetic fields, cable whip and mounting torque. Issues other than mounting and their possible effects are outside the scope of this document.

  • Standard
    21 pages
    English language
    sale 15% off
  • Draft
    20 pages
    English language
    sale 15% off
ISO
ISO 16063-34:2019(Main)
Methods for the calibration of vibration and shock transducers — Part 34: Testing of sensitivity at fixed temperatures

This document details specifications for the instrumentation and methods to be used for testing fixed temperature sensitivity of vibration transducers. It applies to rectilinear velocity and acceleration transducers. The methods specified use both a comparison to a reference transducer and an absolute measurement by laser interferometer. This document is applicable for a frequency range from 10 Hz to 3 kHz (method-dependent), a dynamic range from 1 m/s2 to 100 m/s2 (frequency-dependent) and a temperature range from ?190 °C to 800 °C (method-dependent). Although it is possible to achieve these ranges among all the described systems, generally each has limitations within them. Method 1 (using a laser interferometer) is applicable to magnitude of sensitivity and phase calibration in the frequency range 10 Hz to 3 kHz at fixed temperatures (see Clause 7). Method 2 (using a reference transducer inside a chamber whose temperature limit is ?70 °C to 500 °C) can be used for magnitude of sensitivity and phase calibration in the frequency range 10 Hz to 1 kHz at fixed temperatures (see Clause 8). Method 3 (using a reference transducer outside the chamber) can only be used for the determination of the temperature response of complex sensitivity over a certain temperature range (see Clause 9). NOTE Method 1 and Method 2 can provide the deviation of complex sensitivity over a certain temperature range if the calibration is also done at the reference temperature (room temperature 23 °C ± 5 °C). To ensure the consistency of the use and test condition, the transducer, its cable and the conditioning amplifier are intended to be considered as a single unit and tested together.

  • Standard
    16 pages
    English language
    sale 15% off
ISO
ISO 7626-5:2019(Main)
Mechanical vibration and shock — Experimental determination of mechanical mobility — Part 5: Measurements using impact excitation with an exciter which is not attached to the structure

This document specifies procedures for measuring mechanical mobility and other frequency-response functions of structures excited by means of an impulsive force generated by an exciter which is not attached to the structure under test. It is applicable to the measurement of mobility, accelerance or dynamic compliance, either as a driving point measurement or as a transfer measurement, using impact excitation. Other excitation methods, such as step relaxation and transient random, lead to signal-processing requirements similar to those of impact data. However, such methods are outside the scope of this document because they involve the use of an exciter which is attached to the structure. The signal analysis methods covered are all based on the discrete Fourier transform (DFT), which is performed mostly by a fast Fourier transform (FFT) algorithm. This restriction in scope is based solely on the wide availability of equipment which implements these methods and on the large base of experience in using these methods. It is not intended to exclude the use of other methods currently under development. Impact excitation is also widely used to obtain uncalibrated frequency-response information. For example, a quick impact test which obtains approximate natural frequencies and mode shapes can be quite helpful in planning a random or sinusoidal test for accurate mobility measurements. These uses of impact excitation to obtain qualitative results can be a first stage for mobility measurements. This document is limited to the use of impact excitation techniques for making accurate mobility measurements.

  • Standard
    28 pages
    English language
    sale 15% off
ISO
ISO 16063-44:2018(Main)
Methods for the calibration of vibration and shock transducers — Part 44: Calibration of field vibration calibrators

This document specifies the instrumentation and procedure to be used for performing calibration of field vibration calibrators (FVCs). It is not applicable to FVCs used for the calibration of transducers. These are covered by ISO 16063‑21. Procedures and requirements of in situ calibration by FVC are beyond the scope of this document. Annex B provides more information on the application of FVC.

  • Standard
    10 pages
    English language
    sale 15% off
ISO
ISO 2041:2018(Main)
Mechanical vibration, shock and condition monitoring — Vocabulary

This document defines terms and expressions unique to the areas of mechanical vibration, shock and condition monitoring.

  • Standard
    56 pages
    English language
    sale 15% off
  • Standard
    57 pages
    French language
    sale 15% off
ISO
ISO 18437-6:2017(Main)
Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 6: Time-temperature superposition

ISO 18437-6:2017 specifies a standard method for the acquisition and analysis of data obtained using the test methods found in ISO 18437‑1 to ISO 18437‑5, ISO 6721‑4 to ISO 6721‑7 and ISO 6721‑12. ISO 18437-6:2017 is applicable to visco-elastic materials that are thermorheologically simple and that have been tested at equilibrium state for every temperature.

  • Standard
    24 pages
    English language
    sale 15% off
ISO
ISO 16063-33:2017(Main)
Methods for the calibration of vibration and shock transducers — Part 33: Testing of magnetic field sensitivity

ISO 16063-33:2017 specifies a method, procedures and the specifications for an apparatus to be used for testing the magnetic field sensitivity of vibration and shock transducers. It is applicable to all kinds of vibration and shock transducers. ISO 16063-33:2017 is applicable for a reference test sinusoidal magnetic field having a root mean square (r.m.s.) value more than 10?3 T at 50 Hz or 60 Hz. Typically, a test magnetic field of 10?2 T at 50 Hz or 60 Hz is used. ISO 16063-33:2017 is primarily intended for those who are required to meet internationally standardized methods for the measurement of magnetic field sensitivity under laboratory conditions. NOTE 1 T (tesla) = 1 Wb/m2.

  • Standard
    14 pages
    English language
    sale 15% off
ISO
ISO/TR 19664:2017(Main)
Human response to vibration — Guidance and terminology for instrumentation and equipment for the assessment of daily vibration exposure at the workplace according to the requirements of health and safety

The assessment of human exposure to vibration, to both the hand-arm system and the whole body, at the workplace relies on the combined evaluation of both vibration magnitudes and exposure times. Determining these values can employ various instrumentation types and data sources. ISO/TR 19664:2017 provides guidance and explanation of concepts used for the following: - measurement processes; - instrumentation types; - vibration magnitude source.

  • Technical report
    10 pages
    English language
    sale 15% off
  • Technical report
    10 pages
    French language
    sale 15% off
ISO
ISO 16063-45:2017(Main)
Methods for the calibration of vibration and shock transducers — Part 45: In-situ calibration of transducers with built in calibration coil

ISO 16063-45:2017 specifies the calibration of vibration transducers with built-in calibration coils in laboratory and in situ. In laboratory, the method described can be applied to calibrate the vibration sensitivity and electrical sensitivity, and to obtain the coefficient of calibration coil. In situ, it can be used to calibrate the electrical sensitivity and vibration sensitivity using electrical instrumentation. ISO 16063-45:2017 specifies the instrumentation and procedure for performing calibrations of vibration transducers with built-in calibration coils in the frequency range typically from 0,1 Hz to 100 Hz. The expanded uncertainty can be evaluated using the method given in this document.

  • Standard
    17 pages
    English language
    sale 15% off
ISO
ISO 16063-32:2016(Main)
Methods for the calibration of vibration and shock transducers — Part 32: Resonance testing — Testing the frequency and the phase response of accelerometers by means of shock excitation

ISO 16063-32:2016 lays down detailed specification for instruments and procedures of testing the frequency and the phase response of accelerometers by means of shock excitation. It applies to the accelerometers of the piezoelectric, piezoresistive and variable capacitance types with the damping ratio less than critical and in the frequency range up to 150 kHz. The method presumes that the frequency and the phase responses of the accelerometer under test gained by this method are the best possible characteristics for the mounted accelerometer on the condition that the recommendations for mechanical mounting of accelerometer stated in ISO 5348 are fulfilled and that the mass of the reference shock ball exceeds at least three times the mass of the accelerometer under test. Phase response of the accelerometer under test gained by this method is considered to be some "virtual" characteristic of accelerometer presuming that there is zero phase shift between the input and output signals at a frequency of 0 Hz. NOTE 1 It is intended that the user be aware that for the same accelerometer in the field application, the frequency and the phase responses might be different, depending on the mass and compliance of the test structure and the method of mounting. The method allows just a qualitative evaluation of the frequency and the phase response of accelerometers. NOTE 2 It is intended that the user does not try to get better resolution of the initial parts of the frequency and phase responses of the accelerometer under test than the dynamic range of the adequate characteristic provides it. The best use of the frequency and the phase responses of the accelerometer gained by this method are to get the best fit lines for the initial parts of the mentioned characteristics.

  • Standard
    11 pages
    English language
    sale 15% off