ISO 687:2004
(Main)Solid mineral fuels — Coke — Determination of moisture in the general analysis test sample
Solid mineral fuels — Coke — Determination of moisture in the general analysis test sample
ISO 687:2004 specifies a method for determining the moisture in the general analysis test sample of coke. ISO 687:2004 can be used for the determination of moisture in blast furnace coke, foundry-coke and other high-temperature carbonization products.
Combustibles mineraux solides — Coke — Détermination de l'humidité de l'échantillon pour analyse
Trda mineralna goriva – Koks – Določevanje vlage v preskusnem vzorcu za splošno analizo
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 687
Second edition
2004-09-01
Solid mineral fuels — Coke —
Determination of moisture in the general
analysis test sample
Combustibles mineraux solides — Coke — Détermination de l'humidité
de l'échantillon pour analyse
Reference number
ISO 687:2004(E)
©
ISO 2004
---------------------- Page: 1 ----------------------
ISO 687:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2004 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 687:2004(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Preparation of the test sample . 1
7 Procedure . 2
8 Expression of results . 2
9 Precision . 2
10 Test report . 3
©
ISO 2004 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 687:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 687 was prepared by Technical Committee ISO/TC 27, Solid mineral fuels, Subcommittee SC 5, Methods
of analysis.
This second edition cancels and replaces the first edition (ISO 687:1974), which has been technically revised.
©
iv ISO 2004 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 687:2004(E)
Introduction
The determination of the moisture in the general analysis test sample is required to correct the results of certain
analytical determinations, e.g. volatile matter and hydrogen, for the effect of water in the determination and to
allow all determinations to be corrected to a dry basis.
Since coke is hygroscopic, its moisture will vary with a change in humidity of the atmosphere, and the moisture
in the general analysis test sample should therefore be determined whenever portions are weighed out for other
analytical determinations. If test portions for several analytical determinations are weighed out at the same time,
a single simultaneous moisture determination will suffice to correc
...
SLOVENSKI STANDARD
SIST ISO 687:2005
01-november-2005
7UGDPLQHUDOQDJRULYD±.RNV±'RORþHYDQMHYODJHYSUHVNXVQHPY]RUFX]D
VSORãQRDQDOL]R
Solid mineral fuels -- Coke -- Determination of moisture in the general analysis test
sample
Combustibles mineraux solides -- Coke -- Détermination de l'humidité de l'échantillon
pour analyse
Ta slovenski standard je istoveten z: ISO 687:2004
ICS:
75.160.10 Trda goriva Solid fuels
SIST ISO 687:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 687:2005
---------------------- Page: 2 ----------------------
SIST ISO 687:2005
INTERNATIONAL ISO
STANDARD 687
Second edition
2004-09-01
Solid mineral fuels — Coke —
Determination of moisture in the general
analysis test sample
Combustibles mineraux solides — Coke — Détermination de l'humidité
de l'échantillon pour analyse
Reference number
ISO 687:2004(E)
©
ISO 2004
---------------------- Page: 3 ----------------------
SIST ISO 687:2005
ISO 687:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2004 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 687:2005
ISO 687:2004(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Preparation of the test sample . 1
7 Procedure . 2
8 Expression of results . 2
9 Precision . 2
10 Test report . 3
©
ISO 2004 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 687:2005
ISO 687:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 687 was prepared by Technical Committee ISO/TC 27, Solid mineral fuels, Subcommittee SC 5, Methods
of analysis.
This second edition cancels and replaces the first edition (ISO 687:1974), which has been technically revised.
©
iv ISO 2004 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 687:2005
ISO 687:2004(E)
Introduction
The determination of the moisture in the general analysis test sample is required to correct the results of certain
analytical determinations, e.g. volatile matter and hydrogen, for the effect of water in the determination and to
allow all determinations to be corre
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.