Additive manufacturing of polymers — Qualification principles — Part 1: General principles and preparation of test specimens for PBF-LB

This document specifies the general principles to be followed when test specimens of thermoplastic materials are prepared by laser-based powder bed fusion (PBF-LB/P), which is commonly known as laser sintering. The (PBF-LB/P) process is used to prepare test specimens layer upon layer in which thermal energy selectively fuses regions of a powder bed. This document provides a basis for establishing reproducible and reportable sintering conditions. Its purpose is to promote uniformity in describing the main process parameters, build orientation of the sintering process and also to establish uniform practice in reporting sintering conditions. This document does not specify the test procedure itself.

Fabrication additive de polymères — Principes de qualification — Partie 1: Principes généraux et préparation des éprouvettes pour PBF-LB

Le présent document spécifie les principes généraux à suivre lorsque des éprouvettes en matériaux thermoplastiques sont préparées par fusion laser sur lit de poudre (PBF-LB/P), qui est communément connue comme frittage laser. Le procédé (PBF-LB/P) est utilisé pour préparer des éprouvettes couche après couche, dans lesquelles l’énergie thermique fait fondre de manière sélective des zones d’un lit de poudre. Le présent document fournit une base pour établir des conditions de frittage reproductibles et consignables dans un rapport. Son but est de favoriser l’uniformité des descriptions des principaux paramètres du procédé, l’orientation de fabrication du procédé de frittage, et également d’établir une pratique uniforme de consignation des conditions de frittage dans un rapport. Le présent document ne spécifie pas le mode opératoire d’essai proprement dit.

General Information

Status
Published
Publication Date
12-Jan-2023
Current Stage
6060 - International Standard published
Start Date
13-Jan-2023
Due Date
26-Feb-2023
Completion Date
13-Jan-2023
Ref Project

Relations

Buy Standard

Standard
ISO/ASTM 52936-1:2023 - Additive manufacturing of polymers — Qualification principles — Part 1: General principles and preparation of test specimens for PBF-LB Released:13. 01. 2023
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO/ASTM 52936-1:2023 - Additive manufacturing of polymers — Qualification principles — Part 1: General principles and preparation of test specimens for PBF-LB Released:13. 01. 2023
French language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO/ASTM
STANDARD 52936-1
First edition
2023-01
Additive manufacturing of polymers —
Qualification principles —
Part 1:
General principles and preparation of
test specimens for PBF-LB
Fabrication additive de polymères — Principes de qualification —
Partie 1: Principes généraux et préparation des éprouvettes pour PBF-
LB
Reference number
ISO/ASTM 52936-1:2023(E)
© ISO/ASTM International 2023

---------------------- Page: 1 ----------------------
ISO/ASTM 52936-1:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
Phone: +41 22 749 01 11 Phone: +610 832 9634
Fax: +610 832 9635
Email: copyright@iso.org Email: khooper@astm.org
Website: www.iso.org Website: www.astm.org
Published in Switzerland
ii
  © ISO/ASTM International 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/ASTM 52936-1:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Preparation of test specimen . 3
4.1 General . 3
4.2 Dimensions of test specimen . 3
4.3 Conditioning and preparation of the material . 3
4.4 Test specimens manufacturing . 3
4.4.1 Machine setting . 3
4.4.2 Test specimens processing . 4
4.5 Cleaning, handling and storage of test specimens . 4
5 Report on test-specimen preparation . 4
iii
© ISO/ASTM International 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO/ASTM 52936-1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collab
...

NORME ISO/ASTM
INTERNATIONALE 52936-1
Première édition
2023-01
Fabrication additive de polymères —
Principes de qualification —
Partie 1:
Principes généraux et préparation des
éprouvettes pour PBF-LB
Additive manufacturing of polymers — Qualification principles —
Part 1: General principles and preparation of test specimens for PBF-
LB
Numéro de référence
ISO/ASTM 52936-1:2023(F)
© ISO/ASTM International 2023

---------------------- Page: 1 ----------------------
ISO/ASTM 52936-1:2023(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO/ASTM International 2023
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou un intranet, sans autorisation écrite soit de l’ISO à l’adresse ci-après,
soit d’un organisme membre de l’ISO dans le pays du demandeur. Aux États-Unis, les demandes doivent être adressées à ASTM
International.
ISO copyright office ASTM International
Case postale 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Genève West Conshohocken, PA 19428-2959, USA
Tél.: +41 22 749 01 11 Tél.: +610 832 9634
Fax: +41 22 749 09 47 Fax: +610 832 9635
E-mail: copyright@iso.org E-mail: khooper@astm.org
Web: www.iso.org Web: www.astm.org
Publié en Suisse
ii
  © ISO/ASTM International 2023 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO/ASTM 52936-1:2023(F)
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives .1
3 Termes et définitions . 1
4 Préparation de l’éprouvette .3
4.1 Généralités . 3
4.2 Dimensions de l’éprouvette . 3
4.3 Conditionnement et préparation du matériau . 3
4.4 Fabrication des éprouvettes . 3
4.4.1 Réglage de la machine . . 3
4.4.2 Traitement des éprouvettes . 4
4.5 Nettoyage, manutention et stockage des éprouvettes . 4
5 Rapport sur la préparation de l’éprouvette . 4
iii
© ISO/ASTM International 2023 – Tous droits réservés

---------------------- Page: 3 ----------------------
ISO/ASTM 52936-1:2023(F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Comm
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.