ISO 11884-2:2007
(Main)Optics and photonics — Minimum requirements for stereomicroscopes — Part 2: High performance microscopes
Optics and photonics — Minimum requirements for stereomicroscopes — Part 2: High performance microscopes
ISO 11884-2:2007 specifies minimum requirements for high performance stereomicroscopes. It is not applicable to operation microscopes.
Optique et photonique — Exigences minimales pour les stéréomicroscopes — Partie 2: Microscopes à hautes performances
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 11884-2
Second edition
2007-02-01
Optics and photonics — Minimum
requirements for stereomicroscopes —
Part 2:
High performance microscopes
Optique et photonique — Exigences minimales pour les
stéréomicroscopes —
Partie 2: Microscopes à hautes performances
Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Requirements. 1
5 Test methods. 4
6 Accompanying documents. 4
7 Marking. 4
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11884-2 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 5,
Microscopes and endoscopes.
This second edition cancels and replaces the first edition (ISO 11884-2:1997), which has been technically
revised.
ISO 11884 consists of the following parts, under the general title Optics and photonics — Minimum
requirements for stereomicroscopes:
⎯ Part 1: Stereomicroscopes for general use
⎯ Part 2: High performance microscopes
iv © ISO 2007 – All rights reserved
INTERNATIONAL STANDARD ISO 11884-2:2007(E)
Optics and photonics — Minimum requirements
for stereomicroscopes —
Part 2:
High performance microscopes
1 Scope
This part of ISO 11884 specifies minimum requirements for high performance stereomicroscopes. It is not
applicable to operation microscopes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 7944, Optics and optical instruments — Reference wavelengths
ISO 9022-2, Optics and optical instruments — Environmental test methods — Part 2: Cold, heat and humidity
ISO 9022-3, Optics and optical instruments — Environmental test methods — Part 3: Mechanical stress
ISO 11883, Optics and optical instruments — Microscopes — Marking of stereomicroscopes
ISO 10934-1, Optics and optical instruments — Vocabulary for microscopy — Part 1: Light microscopy
ISO 15227, Optics and optical instruments — Microscopes — Testing of stereomicroscopes
IEC 61010-1:2001, Safety requirements for electrical equipment for measurement, control and laboratory
use — Part 1: General requirements
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 10934-1 apply.
4 Requirements
All the indications given below are minimum requirements. They apply to the reference wavelength in
accordance with ISO 7944.
4.1 Optical and mechanical specifications
The specifications given in Table 1 shall apply.
Testing shall be done in accordance with 5.1.
Table 1 — Requirements for optical and mechanical specif
...
INTERNATIONAL ISO
STANDARD 11884-2
Second edition
2007-02-01
Optics and photonics — Minimum
requirements for stereomicroscopes —
Part 2:
High performance microscopes
Optique et photonique — Exigences minimales pour les
stéréomicroscopes —
Partie 2: Microscopes à hautes performances
Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Requirements. 1
5 Test methods. 4
6 Accompanying documents. 4
7 Marking. 4
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11884-2 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 5,
Microscopes and endoscopes.
This second edition cancels and replaces the first edition (ISO 11884-2:1997), which has been technically
revised.
ISO 11884 consists of the following parts, under the general title Optics and photonics — Minimum
requirements for stereomicroscopes:
⎯ Part 1: Stereomicroscopes for general use
⎯ Part 2: High performance microscopes
iv © ISO 2007 – All rights reserved
INTERNATIONAL STANDARD ISO 11884-2:2007(E)
Optics and photonics — Minimum requirements
for stereomicroscopes —
Part 2:
High performance microscopes
1 Scope
This part of ISO 11884 specifies minimum requirements for high performance stereomicroscopes. It is not
applicable to operation microscopes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 7944, Optics and optical instruments — Reference wavelengths
ISO 9022-2, Optics and optical instruments — Environmental test methods — Part 2: Cold, heat and humidity
ISO 9022-3, Optics and optical instruments — Environmental test methods — Part 3: Mechanical stress
ISO 11883, Optics and optical instruments — Microscopes — Marking of stereomicroscopes
ISO 10934-1, Optics and optical instruments — Vocabulary for microscopy — Part 1: Light microscopy
ISO 15227, Optics and optical instruments — Microscopes — Testing of stereomicroscopes
IEC 61010-1:2001, Safety requirements for electrical equipment for measurement, control and laboratory
use — Part 1: General requirements
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 10934-1 apply.
4 Requirements
All the indications given below are minimum requirements. They apply to the reference wavelength in
accordance with ISO 7944.
4.1 Optical and mechanical specifications
The specifications given in Table 1 shall apply.
Testing shall be done in accordance with 5.1.
Table 1 — Requirements for optical and mechanical specif
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.