ISO/FDIS 21220
(Main)Particulate air filters for general ventilation — Determination of the filtration performance
Particulate air filters for general ventilation — Determination of the filtration performance
ISO 21220:2008 refers to particulate air filters for general ventilation. It describes testing methods and the test rig for measuring filter performance. The test rig is designed for an air flow rate between 0,25 m3/s (900 m3/h, 530 ft3/min) and 1,5 m3/s (5 400 m3/h, 3 178 ft3/min). ISO 21220:2008 applies to air filters having an initial efficiency of less than 99 % with respect to 0,4 µm particles. Filters in the higher end and above 99 % initial efficiency are tested and classified according to other standards. Two test methods are combined in ISO 21220:2008: a “fine method” for air filters in the higher efficiency range and a “coarse method” for lower efficiency filters. In either case, a flat sheet media sample or media pack sample from an identical filter shall be conditioned (discharged) to provide information about the intensity of the electrostatic removal mechanism. After determination of its initial efficiency, the untreated filter is loaded with synthetic dust in one step until its final test-pressure drop is reached. Information on the loaded performance of the filter is then obtained. The performance results obtained in accordance with ISO 21220:2008 cannot, by themselves, be quantitatively applied to predict performance in service with regard to efficiency and lifetime. It is necessary to take into account other factors influencing performance.
Filtres à air de ventilation générale pour l'élimination des particules — Détermination des performances de filtration
General Information
Relations
Standards Content (Sample)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 21220
ISO/TC 142
Particulate air filters for general
Secretariat: UNI
ventilation — Determination of the
Voting begins on:
filtration performance
2008-07-15
Voting terminates on:
Filtres à air de ventilation générale pour l'élimination des particules —
2008-09-15
Détermination des performances de filtration
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORT-
ING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 21220:2008(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2008
---------------------- Page: 1 ----------------------
ISO/FDIS 21220:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2008 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/FDIS 21220:2008(E)
In accordance with the provisions of Council Resolution 15/1993, this document is circulated in the
English language only.
© ISO 2008 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/FDIS 21220:2008(E)
Contents Page
Foreword. vi
Introduction . vii
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Symbols and abbreviated terms. 4
5 Requirements . 6
6 Classification/Rating. 6
7 Test rig and equipment. 6
7.1 Test conditions. 6
7.2 Test rig . 7
7.3 DEHS test aerosol generation.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.