Metal slitting saws with fine and coarse teeth — Metric series

This document specifies the dimensions and the mechanical characteristics of metal slitting saws, metric series. It applies to the following two types of metal slitting saws: — metal slitting saws with fine teeth; — metal slitting saws with coarse teeth. If there is a need to extend the range or introduce other series of teeth, it is intended that such additions be according to the data given in the graph in Annex A.

Fraises-scies à dentures fine et grosse — Série métrique

Le présent document spécifie les dimensions et les caractéristiques mécaniques des fraises-scies de la série métrique. Il s'applique aux deux types de fraises-scies suivants: — fraises-scies à denture fine; — fraises-scies à grosse denture. En cas de besoin d'extension ou de création d'autres séries de denture, il est recommandé de se conformer au graphique donné dans l'Annexe A.

General Information

Status
Published
Publication Date
23-Sep-2018
Current Stage
9060 - Close of review
Start Date
04-Mar-2029
Ref Project

Relations

Buy Standard

Standard
ISO 2296:2018 - Metal slitting saws with fine and coarse teeth -- Metric series
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 2296:2018 - Fraises-scies a dentures fine et grosse -- Série métrique
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 2296
Third edition
2018-09
Metal slitting saws with fine and
coarse teeth — Metric series
Fraises-scies à dentures fine et grosse — Série métrique
Reference number
ISO 2296:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 2296:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 2296:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions and number of teeth . 1
4.1 General . 1
4.2 Dimensions of metal slitting saws with fine teeth . 1
4.3 Dimensions of metal slitting saws with coarse teeth . 3
5 Mechanical characteristics . 3
5.1 Side relief . 3
5.2 Keying . 3
5.3 Metal slitting saws with pine hole drive . 3
Annex A (informative) Determination of the number or pitch of the teeth .4
Annex B (informative) Relationship between designations in this document and ISO 13399
(all parts) . 5
Bibliography . 6
© ISO 2018 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 2296:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to de
...

NORME ISO
INTERNATIONALE 2296
Troisième édition
2018-09
Fraises-scies à dentures fine et
grosse — Série métrique
Metal slitting saws with fine and coarse teeth — Metric series
Numéro de référence
ISO 2296:2018(F)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 2296:2018(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2018 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 2296:2018(F)

Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Dimensions et nombre de dents . 1
4.1 Généralités . 1
4.2 Dimensions des fraises-scies à denture fine. 1
4.3 Dimensions des fraises-scies à grosse denture . 3
5 Caractéristiques mécaniques . 3
5.1 Dépouille latérale . 3
5.2 Clavetage . 3
5.3 Fraises-scies à trou d'entraînement . 3
Annexe A (informative) Détermination du nombre de dents ou du pas de la denture .4
Annexe B (informative) Relation entre les désignations du présent document et celles
des ISO 13399 (toutes les parties) . 5
Bibliographie . 6
© ISO 2018 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 2296:2018(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destiné
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.