ISO 11973:2015

Heat-resistant cast steels and alloys for general applications

ISO 11973:2015 specifies chemical composition and mechanical properties of cast steels and alloys for heat-resistant service.

Aciers et alliages moulés réfractaires destinés à des applications générales

General Information

• Status: Withdrawn
• Publication Date: 07-Sep-2015
• ICS: 77.140.20 - Stainless steels
• ICS: 77.140.80 - Iron and steel castings
• Technical Committee: ISO/TC 17/SC 11 - Steel castings
• Drafting Committee: ISO/TC 17/SC 11 - Steel castings
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 09-Nov-2023

Relations

• Consolidated By: ISO 16140-5:2020 - Microbiology of the food chain — Method validation — Part 5: Protocol for factorial interlaboratory validation for non-proprietary methods
• Effective Date: 06-Jun-2022
• Revised: ISO 11973:2023 - Heat-resistant cast steels and alloys for general applications
• Effective Date: 06-Jun-2022
• Revises: ISO 11973:1999 - Heat-resistant cast steels and alloys for general applications
• Effective Date: 12-Feb-2011

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11973
Second edition
2015-09-15
Heat-resistant cast steels and alloys
for general applications
Aciers et alliages moulés réfractaires destinés à des applications
générales
Reference number
ISO 11973:2015(E)
©
ISO 2015

---------------------- Page: 1 ----------------------
ISO 11973:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11973:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 General conditions for delivery . 1
4 Heat treatment . 1
5 Chemical composition . 1
6 Mechanical properties . 1
7 Maximum use temperature . 1
8 Supplementary requirements . 1
Annex A (informative) UNS cast grades similar to ISO cast grades . 5
Bibliography . 6
© ISO 2015 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 11973:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users
...