ISO/IEC 29642:2007
(Main)Information technology — Data interchange on 120 mm and 80 mm optical disk using +RW DL format — Capacity: 8,55 Gbytes and 2,66 Gbytes per side (recording speed 2,4x)
Information technology — Data interchange on 120 mm and 80 mm optical disk using +RW DL format — Capacity: 8,55 Gbytes and 2,66 Gbytes per side (recording speed 2,4x)
ISO/IEC 29642:2007 specifies the mechanical, physical and optical characteristics of 120 mm rewritable optical disks with capacities of 8,55 Gbytes and 17,1 Gbytes. It specifies the quality of the recorded and unrecorded signals, the format of the data and the recording method, thereby allowing for information interchange by means of such disks. The data can be written, read and overwritten many times using the phase change method. These disks are identified as +RW DL. ISO/IEC 29642:2007 also specifies 80 mm disks with capacities of 2,66 Gbytes and 5,32 Gbytes. These disks have the same characteristics as the 120 mm disks, except for some parameters related to the smaller dimensions. All parameters unique for the 80 mm disks are specified. ISO/IEC 29642:2007 specifies two related but different Types of this disk; the conditions for conformance; the environments in which the disk is to be tested, operated and stored; the mechanical, physical and dimensional characteristics of the disk, so as to provide mechanical interchange between data processing systems; the format of the information on the disk, including the physical disposition of the tracks and sectors, the error correcting codes and the coding method; the characteristics of the signals recorded on the disk, thus enabling data processing systems to read the data from the disk. ISO/IEC 29642:2007 provides for the interchange of disks between optical disk drives. Together with a standard for volume and file structure, it provides for full data interchange between data processing systems.
Technologies de l'information — Échange de données sur disques optiques de 120 mm et 80 mm utilisant le format +RW DL — Capacité: 8,55 Go et 2,66 Go par face (vitesse d'enregistrement 2,4x)
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 29642
First edition
2007-12-01
Information technology — Data
interchange on 120 mm and 80 mm
optical disk using +RW DL format —
Capacity: 8,55 Gbytes and 2,66 Gbytes
per side (recording speed 2,4x)
Technologies de l'information — Échange de données sur disques
optiques de 120 mm et 80 mm utilisant le format +RW DL — Capacité:
8,55 Go et 2,66 Go par face (vitesse d'enregistrement 2,4x)
Reference number
ISO/IEC 29642:2007(E)
©
ISO/IEC 2007
---------------------- Page: 1 ----------------------
ISO/IEC 29642:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 29642:2007(E)
Contents Page
Foreword. vii
Introduction . viii
1 Scope . 1
2 Conformance. 1
2.1 Optical disk. 1
2.2 Generating system. 1
2.3 Receiving system. 2
2.4 Compatibility statement . 2
3 Normative references . 2
4 Terms and definitions. 2
5 Conventions and notations . 4
5.1 Representation of numbers . 4
5.2 Names . 5
6 List of acronyms . 5
7 General description of the optical disk . 6
8 General Requirements. 7
8.1 Environments . 7
8.2 Safety requirements . 7
8.3 Flammability . 8
9 Reference Drive. 8
9.1 Optical system . 8
9.2 Optical beam . 9
9.3 Read channel 1. 9
9.4 Disk clamping. 9
9.5 Rotation of the disk . 10
9.6 Wobble channel (Read channel 2) . 10
9.7 Tracking channel (Read channel 2) . 10
9.8 Reference servo systems . 11
Section 2 – Dimensional, mechanical and physical characteristics of the disk . 14
10 Dimensional characteristics . 14
10.1 Reference Planes. 15
10.2 Overall dimensions. 15
10.3 First transition area . 16
10.4 Second transition area . 16
10.5 Clamping Zone . 16
10.6 Third transition area . 16
10.7 Information Zone. 17
10.8 Rim area. 18
10.9 Remark on tolerances . 18
11 Mechanical characteristics . 18
11.1 Mass . 18
11.2 Moment of inertia. 19
11.3 Dynamic imbalance . 19
11.4 Axial runout . 19
11.5 Radial runout. 19
© ISO/IEC 2007 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 29642:2007(E)
12 Optical characteristics in the Information Zone . 19
12.1 Index of refraction. 19
12.2 Thickness of the substrate. 20
12.3 Reflectivity . 20
12.4 Birefringence . 21
12.5 Angular deviation. 21
Section 3 – Format of information. 22
13 Data format . 22
13.1 Data Frames. 22
13.2 Scrambled Frames . 24
13.3 ECC Blocks. 25
13.4 Recording Frames. 26
13.5 Modulation and NRZI conversion. 27
13.6 Physical Sectors . 28
13.7 Layout of a Recording UNit (RUN). 29
13.8 d.c. component suppression control. 30
14 Track format. 32
14.1 Track shape . 32
14.2 Track path . 32
14.3 Track pitch . 32
14.4 Track layout . 32
Section 4 – Format of the Information Zone. 51
15 General description of the Information Zone . 51
16 Layout of the Information Zone . 52
16.1 Usage of the Data Zone . 52
16.2 Physical Sector Numbers (PSNs). 53
17 Lead-in Zone. 54
17.1 Initial Zone . 54
17.2 Inner Disk Test Zone. 54
17.3 Guard Zone 1 . 55
17.4 Reserved Zone 1 . 55
17.5 Reserved Zone 2 . 55
17.6 Inner Disk Identification Zone. 56
17.7 Reserved Zone 3 . 56
17.8 Reference Code Zone . 56
17.9 Buffer Zone 1 . 56
17.10 Control Data Zone . 56
17.11 Buffer Zone 2 . 59
18 Data Zone. 59
19 Middle Zones . 59
19.1 Buffer Zones 3 . 60
19.2 Reserved Zones 4 . 60
19.3 Guard Zones 2 . 60
20 Outer Drive Areas. 61
20.1 Reserved Zone 5 . 62
20.2 Outer Disk Test Zone . 62
20.3 Guard Zone 3 . 62
21 Lead-out Zone. 62
21.1 Buffer Zone 4 . 63
21.2 Inner Disk Test Zone. 63
21.3 Final Zone . 63
22 Assignment of Logical Sector Numbers (LSNs). 63
23 Formatting. 63
iv © ISO/IEC 2007 – All rights reserved
---------------------- Page: 4 ----------------------
ISO/IEC 29642:2007(E)
23.1 Pre-formatting . 64
23.2 Background formatting . 64
23.3 Sequential recording without formatting .67
24 Disk Control Blocks. 69
24.1 General format of Disk Control Blocks. 69
24.2 Format of the Formatting DCB (FDCB).71
24.3 Format of the Write inhibit DCB (WDCB).77
Section 5 – Characteristics of the groove. 79
25 General. 79
26 Method of testing. 79
26.1 Environment . 79
26.2 Reference Drive. 79
26.3 Definition of signals. 80
27 Characteristics of the groove signals. 80
27.1 Phase depth. 80
27.2 Push-pull signal . 80
27.3 Track Cross signal. 81
27.4 Normalized wobble signal. 81
27.5 Characteristics of the wobble. 81
Section 6 – Characteristics of the recording layer. 82
28 Method of testing. 82
28.1 Environment . 82
28.2 Reference Drive. 82
28.3 Write conditions. 83
28.4 Measurement conditions . 83
29 Characteristics of the recorded signals . 84
29.1 Channel bit length. 84
29.2 Definition of signals. 84
29.3 Read stability. 86
30 Additional testing conditions . 86
30.1 Test environment. 86
30.2 Definition of signals. 87
31 Quality of the recording layer. 89
31.1 Defects . 89
31.2 Data errors. 90
Section 7 – Characteristics of user data . 91
32 Method of testing. 91
32.1 Environment . 91
32.2 Reference Drive. 91
33 Minimum quality of a Recording Unit . 92
33.1 Tracking . 92
33.2 User-written data. 92
Annex A (normative) 80 mm +RW DL disk . 93
Annex B (normative) Structure for Extended format information in the Data Zone . 98
Annex C (normative) Measurement of light reflectivity. 101
Annex D (normative) Measurement of birefringence . 104
Annex E (normative) Measuring conditions for operation signals . 107
Annex F (normative) Measurement of the differential phase tracking error. 110
Annex G (normative) The write pulse wave form for testing. 114
© ISO/IEC 2007 – All rights reserved v
---------------------- Page: 5 ----------------------
ISO/IEC 29642:2007(E)
Annex H (normative) 8-to-16 Modulation . 119
Annex I (normative) Optimum Power Control . 127
Annex J (normative) Logical to Physical address translation. 132
Annex K (informative) Recommended access method for players . 133
Annex L (informative) Measurement of the groove wobble amplitude . 134
Annex M (informative) Transportation. 136
Annex N (informative) Defect Management and Physical Formatting . 137
Annex O (informative) Video Content Protection System . 138
Annex P (informative) How to use the Physical format information in ADIP . 139
Annex Q (informative) Values to be Implemented in Existing and Future Specifications . 141
vi © ISO/IEC 2007 – All rights reserved
---------------------- Page: 6 ----------------------
ISO/IEC 29642:2007(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 29642 was prepared by Ecma International (as ECMA-374) and was adopted, under a special “fast-
track procedure”, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its
approval by national bodies of ISO and IEC.
© ISO/IEC 2007 – All rights reserved vii
---------------------- Page: 7 ----------------------
ISO/IEC 29642:2007(E)
Introduction
Ecma Technical Committee TC 31 was established in 1984 for the standardization of Optical Disks and
Optical Disk Cartridges (ODC). Since its establishment, the Committee has made major contributions to
ISO/IEC toward the development of International Standards for 80 mm, 90 mm, 120 mm, 300 mm, and
356 mm media. Numerous standards have been developed by TC31 and published by Ecma, almost all of
which have also been adopted by ISO/IEC under the fast-track procedure as International Standards.
In June 2006 a group of Companies proposed to TC 31 to develop a standard for 120 mm dual layer
rewritable optical disks using Phase Change recording technology and based on the DVD - Read-Only
standard (ISO/IEC 16448) and the +RW format (ISO/IEC 17341 and ISO/IEC 26925). TC 31 adopted this
project and started the work that has resulted in this International Standard.
This International Standard specifies two Types of rewritable optical disks, one (Type S9) making use of
recording on only a single side of the disk and yielding a nominal capacity of 8,55 Gbytes or 2,66 Gbytes per
disk and the other (Type D18) making use of recording on both sides of the disk and yielding a nominal
capacity of 17,1 Gbytes or 5,32 Gbytes per disk.
This International Standard, taken together with a standard for volume and file structure, such as for instance
developed in Ecma Technical Committee TC 15, provides the requirements for information interchange
between systems.
viii © ISO/IEC 2007 – All rights reserved
---------------------- Page: 8 ----------------------
INTERNATIONAL STANDARD ISO/IEC 29642:2007(E)
Information technology — Data interchange on 120 mm and 80
mm optical disk using +RW DL format — Capacity: 8,55 Gbytes
and 2,66 Gbytes per side (recording speed 2,4x)
1 Scope
This International Standard specifies the mechanical, physical and optical characteristics of 120 mm
rewritable optical disks with capacities
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.