ISO/IEC 23094-4:2022/Amd 1:2024
(Amendment)Information technology — General video coding — Part 4: Conformance and reference software for essential video coding — Amendment 1: Green metadata supplemental enhancement information
Information technology — General video coding — Part 4: Conformance and reference software for essential video coding — Amendment 1: Green metadata supplemental enhancement information
Technologies de l'information — Codage vidéo général — Partie 4: Conformité et logiciel de référence pour le codage vidéo essentiel — Amendement 1: Informations d'amélioration complémentaires des métadonnées vertes
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO/IEC 23094-4
First edition
Information technology — General
2022-01
video coding —
AMENDMENT 1
Part 4:
2024-12
Conformance and reference
software for essential video coding
AMENDMENT 1: Green metadata
supplemental enhancement
information
Reference number
ISO/IEC 23094-4:2022/Amd. 1:2024(en) © ISO/IEC 2024
ISO/IEC 23094-4:2022/Amd. 1:2024(en)
© ISO/IEC 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO/IEC 2024 – All rights reserved
ii
ISO/IEC 23094-4:2022/Amd. 1:2024(en)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical activity.
ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations,
governmental and non-governmental, in liaison with ISO and IEC, also take part in the work.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/
IEC Directives, Part 2 (see www.iso.org/directives or www.iec.ch/members_experts/refdocs).
ISO and IEC draw attention to the possibility that the implementation of this document may involve the
use of (a) patent(s). ISO and IEC take no position concerning the evidence, validity or applicability of any
claimed patent rights in respect thereof. As of the date of publication of this document, ISO and IEC had not
received notice of (a) patent(s) which may be required to implement this document. However, implementers
are cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents and https://patents.iec.ch. ISO and IEC shall not be held
responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www.iso.org/iso/foreword.html.
In the IEC, see www.iec.ch/understanding-standards.
This document was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 29, Coding of audio, picture, multimedia and hypermedia information.
A list of all parts in the ISO/IEC 23090 series can be found on the ISO and IEC websites.
Any feedback or questions on this document should be directed to the user’s national standards
body. A complete listing of these bodies can be found at www.iso.org/members.html and
www.iec.ch/national-committees.
© ISO/IEC 2024 – All rights reserved
iii
ISO/IEC 23094-4:2022/Amd. 1:2024(en)
Information technology — General video coding —
Part 4:
Conformance and reference software for essential video coding
AMENDMENT 1: Green metadata supplemental enhancement
information
6.1, 6.5.2, 6.6.1 and 7.2
Replace https:// standards .iso .org/ iso -iec/ 23094/ -4/ ed -1/ en/ with
https:// standards .iso .org/ iso -iec/ 23094/ -4/ ed -1/ en/ amd/ 1/
6.6.2.43
Add “only” before “ADMVP” in the last sentence.
6.6.2.74 and 6.6.2.75
Replace “CM_init” with “CM_INIT”
6.6.2.95
Remove “only” before “ADDB” in the last sentence.
6.6.2.96
Remove “only” before “ALF” in the last sentence.
6.6.2.97
Remove “only” before “ALF” in the first sentence.
6.6.2.99 and 6.6.2.101
Remove “only” before “HTDF” in the first sentence.
6.6.2.114
Remove “only” before “RPL” in the first sentence.
© ISO/IEC 2024 – All rights reserved
ISO/IEC 23094-4:2022/Amd. 1:2024(en)
6.6.2.116
Remove “only” before “POCS” in the first sentence.
6.6.2.125 to 6.6.2.129
Add the following new subclauses 6.6.2.125 to 6.6.2.129 after subclause 6.6.2.124:
6.6.2.125 Test bitstream BP_SET_C
Specification: Streams with sets of coding tools in Baseline profile.
Functional stage: Test the decoding process of Baseline profile, low delay configuration.
Purpose: Check that the decoder can properly decode bitstreams in which the full set of coding tools is
enabled in Baseline profile, low delay configuration.
6.6.2.126 Test bitstream BP_SET_D
Specification: Streams with sets of coding tools in Baseline profile.
Functional stage: Test the decoding process of Baseline profile, low delay configuration with P slice.
Purpose: Check that the decoder can properly decode bitstreams in which the full set of coding tools is
enabled in Baseline profile, low delay configuration with P slice.
6.6.2.127 Test bitstream ADMVP_I
Specification: Streams with ADMVP is enabled and its dependent tools disabled in Main profile.
Functional stage: Test the decoding process of the inter prediction in Main profile.
Purpose: Check that the decoder can properly decode bitstreams in which ADMVP is enabled and its
dependent tools are disabled in Main profile.
6.6.2.128 Test bitstream ADMVP_J
Specification: Streams with only ADMVP tool enabled in Main profile.
Functional stage: Test the decoding process of the inter prediction in Main profile, low delay configuration
with P slice.
Purpose: Check that the decoder can properly decode bitstreams in which only ADMVP tool is enabled in
Main profile, low delay configuration with P slice.
6.6.2.129 Test bitstream ADMVP_K
Specification: Streams with only ADMVP and its dependent tools enabled in Main profile.
Functional stage: Test the decoding process of the inter prediction in Main profile, low delay configuration
with P slice.
© ISO/IEC 2024 – All rights reserved
ISO/IEC 23094-4:2022/Amd. 1:2024(en)
Purpose: Check that the decoder can properly decode bitstreams in which only ADMVP and its dependent
tools are enabled in Main profile, low delay configuration with P slice.
6.7
Replace Table 1 with the following:
Table 1 — Bitstreams for Baseline and Main profiles
Tool set Baseline profile tool Tool set of Baseline profile BP_SET_A X 5.1 60
set
Baseline Still Picture Tool set of Baseline Still Picture BP_SET_B X NA NA
profile tool set profile
Baseline profile tools Tool set of Baseline profile , low BP_SET_C X 5.1 60
set delay
Baseline profile tools Tool set of Baseline profile , low BP_SET_D X 5.1 60
set delay with P slice
Main profile mini- Minimum tool set of Main profile MP_MIN_A X 5.1 60
mum tool set
Main Still Picture Minimum tool set of Main Still MP_MIN_B X NA NA
profile minimum Picture profile
tool set
Main profile tool set All tools in Main profile enabled MP_SET_A X 5.1 60
Main Still Picture All tools in Main Still MP_SET_B X NA NA
profile tool set Picture profile enabled
Block CTU,CU CTU = 64 CTU_A X 5.1 60
structure (cb_max: 6, cb_min: 2, cu14_max:
6, tris_max: 6, tris_min: 4)
CTU = 32 CTU_B X 5.1 60
(cb_max: 5, cb_min: 2, cu14_max: 5,
tris_max: 5, tris_min: 4, suco_max:
5)
CTU = 128, minCU = 8 CTU_C X 5.1 60
(cb_max: 7, cb_min: 3, cu14_max: 6,
tris_max: 6, tris_min: 5)
CTU = 32, minCU = 32 CTU_D X 5.1 60
(cb_max: 5, cb_min: 5, cu14_max: 5,
tris_max: 5, tris_min: 7)
CTU = 64 CTU_E X NA NA
(cb_max: 6, cb_min: 2, cu14_max:
6, tris_max: 6, tris_min: 4)
CTU = 32 CTU_F X NA NA
(cb_max: 5, cb_min: 2, cu14_max: 5,
tris_max: 5, tris_min: 4, suco_max:
5)
CTU = 128, minCU = 8 CTU_G X NA NA
(cb_max: 7, cb_min: 3, cu14_max: 6,
tris_max: 6, tris_min: 5)
CTU = 32, minCU = 32 CTU_H X NA NA
(cb_max: 5, cb_min: 5, cu14_max: 5,
tris_max: 5, tris_min: 7)
BTT (Binary and BTT structure Off test BTT_A X 5.1 60
ternary split)
BTT structure On test based on BTT_B X 5.1 60
MP_MIN
(cb_max: 7, cb_min: 2, cu14_max: 6,
tris_max: 6, tris_min: 4)
X Bitstream is for static and dynamic tests
© ISO/IEC 2024 – All rights reserved
Categories
Sub category
Description
Bitstream
Baseline
Main
Base Still
Picture
Main Still
Picture
Level
Frame rate
(Frame/sec)
ISO/IEC 23094-4:2022/Amd. 1:2024(en)
TTabablele 1 1 ((ccoonnttiinnueuedd))
Binary split on, ternary off BTT_C X 5.1 60
(cb_max: 7, cb_min: 2, cu14_max: 6,
tris_max: 2, tris_min: 4)
Binary split on, ternary off, BTT_D X 5.1 60
only1:1/1:2/2:1 ratio CUs allowed
(cb_max: 7, cb_min: 2, cu14_max: 2,
tr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.