iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO/R 1501:1970

(Main)

ISO miniature screw threads

ISO miniature screw threads

Filetages miniatures ISO

Miniaturni navoj ISO

General Information

Status
Withdrawn
Publication Date
30-Sep-1970
Withdrawal Date
30-Sep-1970
ICS
21.040.30 - Special screw threads
Technical Committee
ISO/TC 1 - Screw threads
Drafting Committee
ISO/TC 1 - Screw threads
Current Stage
9599 - Withdrawal of International Standard
Completion Date
03-Nov-1998
Ref Project
SIST ISO/R 1501:1998 - ISO miniature screw threads

Relations

Revised
ISO 1501:2009 - ISO miniature screw threads
Effective Date
15-Apr-2008

Buy Standard

ISO/R 1501:1998ISO/R 1501:1998
PreviousNext
Standardization document
ISO/R 1501:1998
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO/R 1501:1998
01-avgust-1998
Miniaturni navoj ISO
ISO miniature screw threads
Filetages miniatures ISO
Ta slovenski standard je istoveten z: ISO/R 1501:1970
ICS:
21.040.30 Posebni navoji Special screw threads
SIST ISO/R 1501:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO/R 1501:1998

---------------------- Page: 2 ----------------------

SIST ISO/R 1501:1998

---------------------- Page: 3 ----------------------

SIST ISO/R 1501:1998

---------------------- Page: 4 ----------------------

SIST ISO/R 1501:1998

---------------------- Page: 5 ----------------------

SIST ISO/R 1501:1998

---------------------- Page: 6 ----------------------

SIST ISO/R 1501:1998

--------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO 1501:2009/Amd 1:2020(Amendment)
ISO miniature screw threads — Amendment 1: The figure for the tolerance zone of external thread
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
ISO
ISO 1501:2009(Main)
ISO miniature screw threads

ISO 1501:2009 specifies the profiles, diameter-pitch combinations, basic dimensions, tolerances, limits of size and designation for ISO miniature screw threads with nominal diameters from 0,3 mm to 1,4 mm. These threads are applicable to timepieces, optical instruments, electrical meters, measuring instruments, etc. The profiles and tolerance system for ISO miniature screw threads (S) differ from the profile and tolerance system for ISO general purpose metric screw threads (M).

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    16 pages
    French language
    sale 15% off
ISO
ISO 1501:2009/Amd 1:2020(Amendment)
ISO miniature screw threads — Amendment 1: The figure for the tolerance zone of external thread
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
ISO
ISO 1501:2009(Main)
ISO miniature screw threads

ISO 1501:2009 specifies the profiles, diameter-pitch combinations, basic dimensions, tolerances, limits of size and designation for ISO miniature screw threads with nominal diameters from 0,3 mm to 1,4 mm. These threads are applicable to timepieces, optical instruments, electrical meters, measuring instruments, etc. The profiles and tolerance system for ISO miniature screw threads (S) differ from the profile and tolerance system for ISO general purpose metric screw threads (M).

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    16 pages
    French language
    sale 15% off
ISO
ISO 7-2:2000(Main)
Pipe threads where pressure-tight joints are made on the threads — Part 2: Verification by means of limit gauges
SIST ISO 7-2:2001

This part of ISO 7 specifies a process using limit gauges, for the validation of taper internal and external threads and parallel internal threads on piping systems components and other products, the dimensions and tolerances of which are detailed in ISO 7-1. The gauging system described may not be suitable, without special precautions, for gauging of threads on injection moulded plastic workpieces. This part of ISO 7 does not cover completely all the requirements necessary for full control of thread quality and dimensions. Additional control of tools and equipment and visual inspection during production are required to ensure complete compliance with ISO 7-1, for example the length of useful thread on internally threaded workpieces should be checked by direct measurement. Annex A gives a summary of the gauges included in this part of ISO 7, together with details of the thread elements controlled by each gauge and gauge identification numbers. In the event of a dispute over compliance with the requirements of ISO 7-1, the gauges in this part of ISO 7 are to be considered as decisive for the thread elements which they control on the workpiece.

  • Standard
    30 pages
    English language
    sale 15% off
  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    32 pages
    French language
    sale 15% off
ISO
ISO 228-1:2000(Main)
Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation

This part of ISO 228 specifies the requirements for thread form, dimensions, tolerances and designation for fastening pipe threads, thread sizes 1/16 to 6 inclusive. Both internal and external threads are parallel threads, intended for the mechanical assembly of the component parts of fittings, cocks and valves, accessories, etc. These threads are not suitable as jointing threads where a pressure-tight joint is made on the thread. If assemblies with such threads must be made pressure-tight, this should be effected by compressing two tightening surfaces outside the threads, and by interposing an appropriate seal. NOTE 1 For pipe threads where pressure-tight joints are made on the threads, see ISO 7-1. NOTE 2 ISO 228-2 gives details of methods for verification of fastening thread dimensions and form, and recommended gauging systems.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    French language
    sale 15% off
ISO
ISO 1478:1999(Main)
Tapping screws thread
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
ISO
ISO 7-1:1994(Main)
Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation
SIST ISO 7-1:1995

Specified the designation and lays down the dimensions and tolerances of pipe threads. Gives terms and definition as well as symbols and explanations including examples of the complete designation for a thread. Figures 1 to 4 illustrate details. Tabulates thread dimensions from 1/16 up to and including 6 inch.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    7 pages
    French language
    sale 15% off
ISO
ISO 228-2:1987(Main)
Pipe threads where pressure-tight joints are not made on the threads — Part 2: Verification by means of limit gauges
SIST ISO 228-2:2001

This second edition cancals and replaces the first edition (1980). Specifies the verification of cylindrical threads, the dimensions and tolerances of which are given in ISO 228-1. Since this 55o profile has different elements to be verified, it is necessary to provide for several GO and several NOT GO gouges.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    13 pages
    French language
    sale 15% off
ISO
ISO 20200:2023(Main)
Plastics — Determination of the degree of disintegration of plastic materials under composting conditions in a laboratory-scale test

This document specifies a method of determining the degree of disintegration of plastic materials when exposed to a laboratory-scale composting environment. The method is not applicable to the determination of the biodegradability of plastic materials under composting conditions. Further testing is necessary to be able to claim compostability.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    French language
    sale 15% off