Hydraulic fluid power cylinders — Dimensions and tolerances of housings for elastomer-energized, plastic-faced seals — Part 1: Piston seal housings

This document specifies the dimensions and associated tolerances for a series of hydraulic cylinder piston seal housings to accommodate elastomer-energized, plastic-faced seals used in reciprocating applications. This document does not stipulate details of seal design, since the manner of construction of seals varies with each manufacturer. The design and material of the seals, and any associated anti-extrusion components, are determined by conditions such as temperature and pressure. This document only applies to the dimensional characteristics of products manufactured in accordance with this document. It does not apply to their functional characteristics.

Vérins hydrauliques — Dimensions et tolérances des logements pour joints en élastomère renforcé par des matières plastiques — Partie 1: Logements de joints de piston

Le présent document spécifie les dimensions et les tolérances associées pour une série de logements de joints de piston destinés à recevoir des joints dynamiques élastomère, à surface plastique utilisés dans les applications à mouvement alternatif. Le présent document ne détaille pas les détails de construction des joints, celle-ci variant avec chaque fabricant. La conception et le matériau des joints, ainsi que ceux des éléments anti-extrusion éventuellement associés sont déterminés par les conditions d'utilisation, telles que température et pression. Le présent document s'applique uniquement aux caractéristiques dimensionnelles de produits fabriqués conformément à ce document. Il ne s'applique pas à leurs caractéristiques fonctionnelles.

Fluidna tehnika - Hidravlika - Mere in tolerance gnezd za z elastomerom - prednapeta plastična tesnila - 1. del: Gnezda batnih tesnilk

Ta dokument določa mere in povezane tolerance za gnezda batnih tesnilk hidravličnih valjev, da ustrezajo z elastomerom prednapetim plastičnim tesnilom za vzajemno uporabo.
Ta dokument ne določa podrobnosti glede zasnove tesnila, saj se način izdelave tesnil posameznih proizvajalcev razlikuje. Konstrukcijo in material tesnil ter povezanih protiekstruzijskih komponent določajo pogoji, kot sta temperatura in tlak.
Ta dokument se uporablja samo za dimenzijske lastnosti izdelkov, izdelanih v skladu s tem dokumentom. Ne uporablja se za njihove funkcionalne lastnosti.

General Information

Status
Published
Publication Date
21-Feb-2021
Current Stage
6060 - International Standard published
Start Date
22-Feb-2021
Due Date
25-Oct-2020
Completion Date
22-Feb-2021

Relations

Buy Standard

Standard
ISO 7425-1:2022
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 7425-1:2022
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 7425-1:2021 - Hydraulic fluid power cylinders -- Dimensions and tolerances of housings for elastomer-energized, plastic-faced seals
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 7425-1:2021 - Vérins hydrauliques -- Dimensions et tolérances des logements pour joints en élastomère renforcé par des matières plastiques
French language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 7425-1:Version 21-nov-2020 - Hydraulic fluid power cylinders -- Dimensions and tolerances of housings for elastomer-energized, plastic-faced seals
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 7425-1:Version 19-dec-2020 - Vérins hydrauliques -- Dimensions et tolérances des logements pour joints en élastomere renforcé par des matieres plastiques
French language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 7425-1:2022
01-april-2022
Nadomešča:
SIST ISO 7425-1:1997
Fluidna tehnika - Hidravlika - Mere in tolerance gnezd za z elastomerom -
prednapeta plastična tesnila - 1. del: Gnezda batnih tesnilk
Hydraulic fluid power cylinders - Dimensions and tolerances of housings for elastomer-
energized, plastic-faced seals - Part 1: Piston seal housings
Vérins hydrauliques -- Dimensions et tolérances des logements pour joints en
élastomère renforcé par des matières plastiques
Ta slovenski standard je istoveten z: ISO 7425-1:2021
ICS:
23.100.20 Hidravlični valji Cylinders
SIST ISO 7425-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 7425-1:2022

---------------------- Page: 2 ----------------------
SIST ISO 7425-1:2022
INTERNATIONAL ISO
STANDARD 7425-1
Second edition
2021-02
Hydraulic fluid power cylinders —
Dimensions and tolerances of
housings for elastomer-energized,
plastic-faced seals —
Part 1:
Piston seal housings
Vérins hydrauliques — Dimensions et tolérances des logements pour
joints en élastomère renforcé par des matières plastiques —
Partie 1: Logements de joints de piston
Reference number
ISO 7425-1:2021(E)
©
ISO 2021

---------------------- Page: 3 ----------------------
SIST ISO 7425-1:2022
ISO 7425-1:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 7425-1:2022
ISO 7425-1:2021(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Seal housings . 2
5.1 General . 2
5.2 Axial length. 3
5.3 Radial depth . 3
6 Dimensions and tolerances . 3
7 Extrusion gap . 3
8 Surface finish . 3
8.1 General statement . 3
8.2 Sliding and static sealing surfaces . 3
9 Lead-in chamfer . 4
10 Identification statement . 5
Bibliography . 8
© ISO 2021 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 7425-1:2022
ISO 7425-1:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee
SC 7, Sealing devices.
This second edition cancels and replaces the first edition (ISO 7425-1:1988), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— 60 bore was added to Table 3 to ensure consistency with ISO 3320 and to Clause 8 to ensure
consistency with ISO 5597.
A list of all parts in the ISO 7425 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user's national standards body.
A complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 6 ----------------------
SIST ISO 7425-1:2022
ISO 7425-1:2021(E)

Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure
within an enclosed circuit. Sealing devices are used to contain the pressurized fluid with components
with elements with linear motion, i.e. hydraulic cylinders. In general, these sealing devices are used
with both cylinder rod and piston seal housings. This document covers piston seal housings.
This document is one part of the ISO 7425 series of standards covering dimensions and tolerances of
reciprocating seal housings.
© ISO 2021 – All rights reserved v

---------------------- Page: 7 ----------------------
SIST ISO 7425-1:2022

---------------------- Page: 8 ----------------------
SIST ISO 7425-1:2022
INTERNATIONAL STANDARD ISO 7425-1:2021(E)
Hydraulic fluid power cylinders — Dimensions and
tolerances of housings for elastomer-energized, plastic-
faced seals —
Part 1:
Piston seal housings
1 Scope
This document specifies the dimensions and associated tolerances for a series of hydraulic cylinder
piston seal housings to accommodate elastomer-energized, plastic-faced seals used in reciprocating
applications.
This document does not stipulate details of seal design, since the manner of construction of seals
varies with each manufacturer. The design and material of the seals, and any associated anti-extrusion
components, are determined by conditions such as temperature and pressure.
This document only applies to the dimensional characteristics of products manufactured in accordance
with this document. It does not apply to their functional characteristics.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3320, Fluid power systems and components — Cylinder bores and piston rod diameters and area
ratios — Metric series
ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters
ISO 5598, Fluid power systems and components — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
ISO and IEC maintain terminological database
...

SLOVENSKI STANDARD
SIST ISO 7425-1:2022
01-april-2022
Nadomešča:
SIST ISO 7425-1:1997
Hidravlični fluidni cilindri - Mere in tolerance gnezd za elastomere - vzbujan,
tesnilo s plastičnim čelom - 1. del: Gnezda batnih tesnilk
Hydraulic fluid power cylinders - Dimensions and tolerances of housings for elastomer-
energized, plastic-faced seals - Part 1: Piston seal housings
Vérins hydrauliques -- Dimensions et tolérances des logements pour joints en
élastomère renforcé par des matières plastiques
Ta slovenski standard je istoveten z: ISO 7425-1:2021
ICS:
23.100.20 Hidravlični valji Cylinders
SIST ISO 7425-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 7425-1:2022

---------------------- Page: 2 ----------------------
SIST ISO 7425-1:2022
INTERNATIONAL ISO
STANDARD 7425-1
Second edition
2021-02
Hydraulic fluid power cylinders —
Dimensions and tolerances of
housings for elastomer-energized,
plastic-faced seals —
Part 1:
Piston seal housings
Vérins hydrauliques — Dimensions et tolérances des logements pour
joints en élastomère renforcé par des matières plastiques —
Partie 1: Logements de joints de piston
Reference number
ISO 7425-1:2021(E)
©
ISO 2021

---------------------- Page: 3 ----------------------
SIST ISO 7425-1:2022
ISO 7425-1:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 7425-1:2022
ISO 7425-1:2021(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Seal housings . 2
5.1 General . 2
5.2 Axial length. 3
5.3 Radial depth . 3
6 Dimensions and tolerances . 3
7 Extrusion gap . 3
8 Surface finish . 3
8.1 General statement . 3
8.2 Sliding and static sealing surfaces . 3
9 Lead-in chamfer . 4
10 Identification statement . 5
Bibliography . 8
© ISO 2021 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 7425-1:2022
ISO 7425-1:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee
SC 7, Sealing devices.
This second edition cancels and replaces the first edition (ISO 7425-1:1988), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— 60 bore was added to Table 3 to ensure consistency with ISO 3320 and to Clause 8 to ensure
consistency with ISO 5597.
A list of all parts in the ISO 7425 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user's national standards body.
A complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 6 ----------------------
SIST ISO 7425-1:2022
ISO 7425-1:2021(E)

Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure
within an enclosed circuit. Sealing devices are used to contain the pressurized fluid with components
with elements with linear motion, i.e. hydraulic cylinders. In general, these sealing devices are used
with both cylinder rod and piston seal housings. This document covers piston seal housings.
This document is one part of the ISO 7425 series of standards covering dimensions and tolerances of
reciprocating seal housings.
© ISO 2021 – All rights reserved v

---------------------- Page: 7 ----------------------
SIST ISO 7425-1:2022

---------------------- Page: 8 ----------------------
SIST ISO 7425-1:2022
INTERNATIONAL STANDARD ISO 7425-1:2021(E)
Hydraulic fluid power cylinders — Dimensions and
tolerances of housings for elastomer-energized, plastic-
faced seals —
Part 1:
Piston seal housings
1 Scope
This document specifies the dimensions and associated tolerances for a series of hydraulic cylinder
piston seal housings to accommodate elastomer-energized, plastic-faced seals used in reciprocating
applications.
This document does not stipulate details of seal design, since the manner of construction of seals
varies with each manufacturer. The design and material of the seals, and any associated anti-extrusion
components, are determined by conditions such as temperature and pressure.
This document only applies to the dimensional characteristics of products manufactured in accordance
with this document. It does not apply to their functional characteristics.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3320, Fluid power systems and components — Cylinder bores and piston rod diameters and area
ratios — Metric series
ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters
ISO 5598, Fluid power systems and components — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
ISO and IEC maintain terminological databa
...

INTERNATIONAL ISO
STANDARD 7425-1
Second edition
2021-02
Hydraulic fluid power cylinders —
Dimensions and tolerances of
housings for elastomer-energized,
plastic-faced seals —
Part 1:
Piston seal housings
Vérins hydrauliques — Dimensions et tolérances des logements pour
joints en élastomère renforcé par des matières plastiques —
Partie 1: Logements de joints de piston
Reference number
ISO 7425-1:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 7425-1:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7425-1:2021(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Seal housings . 2
5.1 General . 2
5.2 Axial length. 3
5.3 Radial depth . 3
6 Dimensions and tolerances . 3
7 Extrusion gap . 3
8 Surface finish . 3
8.1 General statement . 3
8.2 Sliding and static sealing surfaces . 3
9 Lead-in chamfer . 4
10 Identification statement . 5
Bibliography . 8
© ISO 2021 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 7425-1:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee
SC 7, Sealing devices.
This second edition cancels and replaces the first edition (ISO 7425-1:1988), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— 60 bore was added to Table 3 to ensure consistency with ISO 3320 and to Clause 8 to ensure
consistency with ISO 5597.
A list of all parts in the ISO 7425 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user's national standards body.
A complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 7425-1:2021(E)

Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure
within an enclosed circuit. Sealing devices are used to contain the pressurized fluid with components
with elements with linear motion, i.e. hydraulic cylinders. In general, these sealing devices are used
with both cylinder rod and piston seal housings. This document covers piston seal housings.
This document is one part of the ISO 7425 series of standards covering dimensions and tolerances of
reciprocating seal housings.
© ISO 2021 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 7425-1:2021(E)
Hydraulic fluid power cylinders — Dimensions and
tolerances of housings for elastomer-energized, plastic-
faced seals —
Part 1:
Piston seal housings
1 Scope
This document specifies the dimensions and associated tolerances for a series of hydraulic cylinder
piston seal housings to accommodate elastomer-energized, plastic-faced seals used in reciprocating
applications.
This document does not stipulate details of seal design, since the manner of construction of seals
varies with each manufacturer. The design and material of the seals, and any associated anti-extrusion
components, are determined by conditions such as temperature and pressure.
This document only applies to the dimensional characteristics of products manufactured in accordance
with this document. It does not apply to their functional characteristics.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3320, Fluid power systems and components — Cylinder bores and piston rod diameters and area
ratios — Metric series
ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters
ISO 5598, Fluid power systems and components — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
© ISO 2021 – All rights reserved 1

---------------------- Page: 6 ----------------------
ISO 7425-1:2021(E)

4 Symbols
a roughness of the side surface of the seal housing
b roughness of the static pressure mating surface of the seal housing
C axial length of the lead-in chamfer
C0 reference material ratio level (see ISO 4287:1997, 4.5
...

NORME ISO
INTERNATIONALE 7425-1
Deuxième édition
2021-02
Vérins hydrauliques — Dimensions
et tolérances des logements pour
joints en élastomère renforcé par des
matières plastiques —
Partie 1:
Logements de joints de piston
Hydraulic fluid power cylinders — Dimensions and tolerances of
housings for elastomer-energized, plastic-faced seals —
Part 1: Piston seal housings
Numéro de référence
ISO 7425-1:2021(F)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 7425-1:2021(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2021 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 7425-1:2021(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Symboles . 2
5 Logements de joints . 2
5.1 Généralités . 2
5.2 Longueur axiale . 3
5.3 Profondeur radiale . 3
6 Dimensions et tolérances . 3
7 Intervalle d'extrusion . 3
8 État de surface . 3
8.1 Constat général . 3
8.2 Surfaces d'étanchéité dynamiques et statiques . 3
9 Chanfrein d'entrée . 4
10 Phrase d’identification . 5
Bibliographie . 8
© ISO 2021 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 7425-1:2021(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 131, Transmissions hydrauliques et
pneumatiques, sous-comité SC7, Dispositifs d'étanchéité.
Cette deuxième édition annule et remplace la première édition (ISO 7425-1:1988), qui a fait l’objet d’une
révision technique.
Les principales modifications par rapport à l’édition précédente sont les suivantes:
— Ajout de l’alésage 60 dans le Tableau 3 par cohérence avec l’ISO 3320 et ajout de l’Article 8 par
cohérence avec l’ISO 5597.
Une liste de toutes les parties de la série ISO 7425 se trouve sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse https:// www .iso .org/ fr/ members .html.
iv © ISO 2021 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 7425-1:2021(F)

Introduction
Dans les systèmes de transmissions hydrauliques, l'énergie est transmise et commandée par
l'intermédiaire d'un liquide sous pression circulant en circuit fermé. Les dispositifs d'étanchéité sont
utilisés pour maintenir le fluide sous pression dans les composants ayant des éléments animés d'un
mouvement linéaire, c’est-à-dire des vérins hydrauliques. En général, ces dispositifs d'étanchéité sont
utilisés avec des logements de joint pour tiges de piston et pour pistons de vérins. Le présent document
traite des logements de joints de piston.
Le présent document fait partie de la série de normes ISO 7425 traitant des dimensions et tolérances
des logements de joints à mouvement alternatif.
© ISO 2021 – Tous droits réservés v

---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 7425-1:2021(F)
Vérins hydrauliques — Dimensions et tolérances des
logements pour joints en élastomère renforcé par des
matières plastiques —
Partie 1:
Logements de joints de piston
1 Domaine d'application
Le présent document spécifie les dimensions et les tolérances associées pour une série de logements de
joints de piston destinés à recevoir des joints dynamiques élastomère, à surface plastique utilisés dans
les applications à mouvement alternatif.
Le présent document ne détaille pas les détails de construction des joints, celle-ci variant avec
chaque fabricant. La conception et le matériau des joints, ainsi que ceux des éléments anti-extrusion
éventuellement associés sont déterminés par les conditions d’utilisation, telles que température et
pression.
Le présent document s’applique uniquement aux caractéristiques dimensionnelles de produits fabriqués
conformément à ce document. Il ne s’applique pas à leurs caractéristiques fonctionnelles.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s'applique (y compris les
éventuels amendements).
ISO 3320, Transmissions et composants hydrauliques et pneumatiques — Alésages des vérins et diamètres
des tiges de piston et rapports de surface — Série métrique
ISO 4287:1997, Spécification géométrique des produits (GPS) — État de surface: Méthode du profil —
Termes, définitions et paramètres d'état de surface
ISO 5598, Transmissions hydrauliques et pneumatiques — Vocabulaire
3 Termes et définitions
Pour les besoins du présent document, les définitions données dans l’ISO 5598 s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse http:// www .electropedia .org/
© ISO 2021 – Tous droits réservés 1

---------------------- Page: 6 ----------------------
ISO 7425-1:2021(F)

4 Symboles
a rugosité de la surface latérale du logement de joint
b rugosité de la surface d'ajustement de pression statique du logement de joint
C longueur axiale du chanfrein d’entrée
C0 taux de longueur portante par rapport à une référence (voir ISO 4287:1997, 4.5.4)
D diamètre d'alésage (diamètre extérieur du logement de joint)
d diamètre de la gorge du joint de piston (diamètre intérieur du logement de joint)
d diamètre de passage du piston
3
e
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 7425-1
ISO/TC 131/SC 7
Hydraulic fluid power cylinders —
Secretariat: JISC
Dimensions and tolerances of
Voting begins on:
2020-11-27 housings for elastomer-energized,
plastic-faced seals —
Voting terminates
on: 2021-01-22
Part 1:
Piston seal housings
Vérins hydrauliques — Dimensions et tolérances des logements pour
joints en élastomère renforcé par des matières plastiques —
Partie 1: Logements de joints de piston
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 7425-1:2020(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2020

---------------------- Page: 1 ----------------------
ISO/FDIS 7425-1:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 7425-1:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 1
5 Seal housings . 2
5.1 General . 2
5.2 Axial length. 2
5.3 Radial depth . 3
6 Dimensions and tolerances . 3
7 Extrusion gap . 3
8 Surface finish . 3
8.1 General statement . 3
8.2 Sliding and static sealing surfaces . 3
9 Lead-in chamfer . 4
10 Identification statement . 5
Bibliography . 8
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/FDIS 7425-1:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee
SC 7, Sealing devices.
This second edition cancels and replaces the first edition (ISO 7425-1:1988), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— 60 bore was added to Table 3 to ensure consistency with ISO 3320 and to Clause 8 to ensure
consistency with ISO 5597.
A list of all parts in the ISO 7425 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user's national standards body.
A complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/FDIS 7425-1:2020(E)

Introduction
In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure
within an enclosed circuit. Sealing devices are used to contain the pressurized fluid with components
with elements with linear motion, i.e. hydraulic cylinders. In general, these sealing devices are used
with both cylinder rod and piston seal housings. This document covers piston seal housings.
This document is one part of the ISO 7425 series of standards covering dimensions and tolerances of
reciprocating seal housings.
© ISO 2020 – All rights reserved v

---------------------- Page: 5 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 7425-1:2020(E)
Hydraulic fluid power cylinders — Dimensions and
tolerances of housings for elastomer-energized, plastic-
faced seals —
Part 1:
Piston seal housings
1 Scope
This document specifies the dimensions and associated tolerances for a series of hydraulic cylinder
piston seal housings to accommodate elastomer-energized, plastic-faced seals used in reciprocating
applications.
This document does not stipulate details of seal design, since the manner of construction of seals
varies with each manufacturer. The design and material of the seals, and any associated anti-extrusion
components, are determined by conditions such as temperature and pressure.
This document only applies to the dimensional characteristics of products manufactured in accordance
with this document. It does not apply to their functional characteristics.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3320, Fluid power systems and components — Cylinder bores and piston rod diameters and area
ratios — Metric series
ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters
ISO 5598, Fluid power systems and components — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 Symbols
a roughness of the side surface of the sea
...

PROJET
NORME ISO/FDIS
FINAL
INTERNATIONALE 7425-1
ISO/TC 131/SC 7
Vérins hydrauliques — Dimensions
Secrétariat: JISC
et tolérances des logements pour
Début de vote:
2020-11-27 joints en élastomère renforcé par des
matières plastiques —
Vote clos le:
2021-01-22
Partie 1:
Logements de joints de piston
Hydraulic fluid power cylinders — Dimensions and tolerances of
housings for elastomer-energized, plastic-faced seals —
Part 1: Piston seal housings
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSER-
VATIONS, NOTIFICATION DES DROITS DE PRO-
PRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT
CONNAISSANCE ET À FOURNIR UNE DOCUMEN-
TATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-
Numéro de référence
MERCIALES, AINSI QUE DU POINT DE VUE
ISO/FDIS 7425-1:2020(F)
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR POSSI-
BILITÉ DE DEVENIR DES NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTA-
©
TION NATIONALE. ISO 2020

---------------------- Page: 1 ----------------------
ISO/FDIS 7425-1:2020(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2020
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO/FDIS 7425-1:2020(F)

Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Symboles littéraux . 2
5 Logements de joints . 2
5.1 Généralités . 2
5.2 Longueur axiale . 3
5.3 Profondeur radiale . 3
6 Dimensions et tolérances . 3
7 Intervalle d'extrusion . 3
8 Etat de surface . 3
8.1 Constat général . 3
8.2 Surfaces d'étanchéité dynamiques et statiques . 3
9 Chanfrein d'entrée . 4
10 Phrase d’identification . 5
Bibliographie . 8
© ISO 2020 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO/FDIS 7425-1:2020(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www .iso .org/ iso/ fr/ avant -propos .html.
Le présent document a été élaboré par le comité technique ISO/TC 131 Transmissions hydrauliques et
pneumatiques, sous-comité SC7, Dispositifs d'étanchéité.
Cette deuxième édition annule et remplace la première édition (ISO 7425-1:1988), qui a fait l’objet d’une
révision technique.
Les principales modifications par rapport à l’édition précédente sont les suivantes:
— ajout de l’alésage 60 dans le Tableau 3 par cohérence avec l’ISO 3320 et ajout de l’Article 8 Rugosité
de surface par cohérence avec l’ISO 5597:2018
Une liste de toutes les parties de la série ISO 7425 se trouve sur le site Web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse https:// www .iso .org/ fr/ members .html.
iv © ISO 2020 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO/FDIS 7425-1:2020(F)

Introduction
Dans les systèmes de transmissions hydrauliques, l'énergie est transmise et commandée par
l'intermédiaire d'un liquide sous pression circulant en circuit fermé. Les dispositifs d'étanchéité sont
utilisés pour maintenir le fluide sous pression dans les composants ayant des éléments animés d'un
mouvement linéaire, c’est-à-dire des vérins hydrauliques. En général, ces dispositifs d'étanchéité sont
utilisés avec des logements de joint pour tiges de piston et pour pistons de vérins. Le présent document
traite des logements de joints de piston.
Le présent document fait partie de la série de normes ISO 7425 traitant des dimensions et tolérances
des logements de joints à mouvement alternatif.
© ISO 2020 – Tous droits réservés v

---------------------- Page: 5 ----------------------
PROJET FINAL DE NORME INTERNATIONALE ISO/FDIS 7425-1:2020(F)
Vérins hydrauliques — Dimensions et tolérances des
logements pour joints en élastomère renforcé par des
matières plastiques —
Partie 1:
Logements de joints de piston
1 Domaine d'application
Le présent document spécifie les dimensions et les tolérances associées pour une série de logements de
joints de piston destinés à recevoir des joints dynamiques élastomère, à surface plastique utilisés dans
applications à mouvement alternatif.
Le présent document ne détaille pas les détails de construction des joints, celle-ci variant avec
chaque fabricant. La conception et le matériau des joints, ainsi que ceux des éléments anti-extrusion
éventuellement associés sont déterminés par les conditions d’utilisation, telles que température et
pression.
Le présent document s’applique uniquement aux caractéristiques dimensionnelles de produits fabriqués
conformément à ce document. Elle ne s’applique pas à leurs caractéristiques fonctionnelles.
2 Références normatives
Les documents suivants sont référencés dans le texte de telle sorte qu'une partie ou la totalité de leur
contenu constitue les exigences du présent document. Pour les références datées, seule l'édition citée
s'applique. Pour les références non datées, la dernière édition du document de référence s'applique (y
compris les éventuels amendements).
ISO 3320, Transmissions et composants hydrauliques et pneumatiques — Alésages des vérins et diamètres
des tiges de piston et rapports de surface — Série métrique
ISO 4287:1997, Spécification géométrique des produits (GPS) — État de surface: Méthode du profil —
Termes, définitions et paramètres d'état de surface
ISO 5598, Transmissions hydrauliques et pneumatiques — Vocabulaire
3 Termes et définitions
Pour les besoins du présent document, les définitions données dans l’ISO 5598 s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse http:// www .electropedia .org/
© ISO 2020 – Tous droits réservés 1

---------------------- Page: 6 ----------------------
ISO/FDIS 7425-1:2020(F)

4 Symboles littéraux
a rugosité de la surface latérale du logement de joint
b rugosité
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.