Plastics — Thermosetting moulding materials — Determination of shrinkage

ISO 2577:2007 specifies a method of determining the moulding shrinkage and the shrinkage after heat treatment of moulded test specimens of thermosetting moulding materials. These characteristics are useful for the production control of thermosetting material and for checking uniformity of manufacture. Furthermore, knowledge of the initial shrinkage of thermosetting materials is important for the construction of moulds, and knowledge of post-shrinkage for establishing the suitability of the moulding material for the manufacture of moulded pieces with accurate dimensions.

Plastiques — Matières à mouler thermodurcissables — Détermination du retrait

L'ISO 2577:2007 spécifie une méthode de détermination du retrait de moulage et du retrait après traitement thermique des éprouvettes moulées en matières à mouler thermodurcissables. Ces caractéristiques sont utiles pour le contrôle de la production des matières thermodurcissables et la vérification de l'uniformité de fabrication. En outre, la connaissance du retrait initial des matières thermodurcissables est importante pour la construction des moules, et celle du post-retrait pour la détermination de l'aptitude de la matière à mouler à la fabrication de pièces moulées de dimensions précises.

Polimerni materiali - Duromerni materiali za oblikovanje - Ugotavljanje skrčka

Ta mednarodni standard določa metodo za ugotavljanje skrčka pri oblikovanju in skrčka po toplotni obdelavi oblikovanih preskušancev iz duromernih materialov za oblikovanje. Te lastnosti so uporabne za kontrolo proizvodnje duromernih materialov in za preverjanje enotnosti proizvodnje. Poleg tega je poznavanje začetnega krčenja duromernih materialov pomembno za izdelavo kalupov, poznavanje naknadnega krčenja pa za ugotavljanje primernosti materiala za oblikovanje za izdelavo oblikovanih kosov z natančnimi merami.

General Information

Status
Published
Publication Date
02-Dec-2007
Current Stage
9093 - International Standard confirmed
Completion Date
04-Sep-2020

Relations

Buy Standard

Standard
ISO 2577:2007 - Plastics -- Thermosetting moulding materials -- Determination of shrinkage
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 2577:2015
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 2577:2007 - Plastiques -- Matieres a mouler thermodurcissables -- Détermination du retrait
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 2577
Third edition
2007-12-15

Plastics — Thermosetting moulding
materials — Determination of shrinkage
Plastiques — Matières à mouler thermodurcissables — Détermination
du retrait




Reference number
ISO 2577:2007(E)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 2577:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 2577:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2577 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 12, Thermosetting
materials.
This third edition cancels and replaces the second edition (ISO 2577:1984), which has been technically
revised.

© ISO 2007 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 2577:2007(E)

Plastics — Thermosetting moulding materials — Determination
of shrinkage
1 Scope
This International Standard specifies a method of determining the moulding shrinkage and the shrinkage after
heat treatment of moulded test specimens of thermosetting moulding materials.
These characteristics are useful for the production control of thermosetting material and for checking
uniformity of manufacture. Furthermore, knowledge of the initial shrinkage of thermosetting materials is
important for the construction of moulds, and knowledge of post-shrinkage for establishing the suitability of the
moulding material for the manufacture of moulded pieces with accurate dimensions.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 295, Plastics — Compression moulding of test specimens of thermosetting materials
ISO 10724-1, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds
(PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 10724-2, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds
(PMCs) — Part 2: Small plates
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
moulding shrinkage
difference in dimensions between a moulding and the mould cavity in which it was moulded, both the mould
and the moulding being at normal temperature when measured
3.2
post-shrinkage
shrinkage of a plastic product after moulding, during post-treatment, storage or use
4 Apparatus
4.1 Mould, press, etc., suitable for moulding the test specimens specified in Clause 6. For compression
moulding, a positive or a semi-positive mould with single or multiple cavities shall be used. For injection
moulding, the type D2 ISO mould, giving 60 mm × 60 mm × 2 mm specimens, as specified in
ISO 10724-2:1998, Clause 4, shall be used.
© ISO 2007 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 2577:2007(E)
If required, marks may be engraved in the mould near opposite ends of the specimen to facilitate the accurate
measurement of the length of the cavity and the specimens.
NOTE If multiple cavities are used with a positive mould, resulting variations in test specimen density may be
sufficient to produce inconsistent shrinkage.
4.2 Equipment, suitable for measuring the lengths of the test specimen and the corresponding cavity of the
mould to within 0,02 mm.
4.3 Oven (for post-shrinkage only).
5 Sampling
A representative sample shall be t
...

SLOVENSKI STANDARD
SIST ISO 2577:2015
01-marec-2015
3ROLPHUQLPDWHULDOL'XURPHUQLPDWHULDOL]DREOLNRYDQMH8JRWDYOMDQMHVNUþND
Plastics - Thermosetting moulding materials - Determination of shrinkage
Plastiques - Matières à mouler thermodurcissables - Détermination du retrait
Ta slovenski standard je istoveten z: ISO 2577:2007
ICS:
83.080.10 Duromeri Thermosetting materials
SIST ISO 2577:2015 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 2577:2015

---------------------- Page: 2 ----------------------

SIST ISO 2577:2015

INTERNATIONAL ISO
STANDARD 2577
Third edition
2007-12-15

Plastics — Thermosetting moulding
materials — Determination of shrinkage
Plastiques — Matières à mouler thermodurcissables — Détermination
du retrait




Reference number
ISO 2577:2007(E)
©
ISO 2007

---------------------- Page: 3 ----------------------

SIST ISO 2577:2015
ISO 2577:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 2577:2015
ISO 2577:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2577 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 12, Thermosetting
materials.
This third edition cancels and replaces the second edition (ISO 2577:1984), which has been technically
revised.

© ISO 2007 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 2577:2015

---------------------- Page: 6 ----------------------

SIST ISO 2577:2015
INTERNATIONAL STANDARD ISO 2577:2007(E)

Plastics — Thermosetting moulding materials — Determination
of shrinkage
1 Scope
This International Standard specifies a method of determining the moulding shrinkage and the shrinkage after
heat treatment of moulded test specimens of thermosetting moulding materials.
These characteristics are useful for the production control of thermosetting material and for checking
uniformity of manufacture. Furthermore, knowledge of the initial shrinkage of thermosetting materials is
important for the construction of moulds, and knowledge of post-shrinkage for establishing the suitability of the
moulding material for the manufacture of moulded pieces with accurate dimensions.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 295, Plastics — Compression moulding of test specimens of thermosetting materials
ISO 10724-1, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds
(PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 10724-2, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds
(PMCs) — Part 2: Small plates
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
moulding shrinkage
difference in dimensions between a moulding and the mould cavity in which it was moulded, both the mould
and the moulding being at normal temperature when measured
3.2
post-shrinkage
shrinkage of a plastic product after moulding, during post-treatment, storage or use
4 Apparatus
4.1 Mould, press, etc., suitable for moulding the test specimens specified in Clause 6. For compression
moulding, a positive or a semi-positive mould with single or multiple cavities shall be used. For injection
moulding, the type D2 ISO mould, giving 60 mm × 60 mm × 2 mm specimens, as specified in
ISO 10724-2:1998, Clause 4, shall be used.
© ISO 2007 – All rights reserved 1

---------------------- Page: 7 ----------------------

SIST ISO 2577:2015
ISO 2577:2007(E)
If required, marks may be engraved in the mould near opposite ends of the
...

NORME ISO
INTERNATIONALE 2577
Troisième édition
2007-12-15


Plastiques — Matières à mouler
thermodurcissables — Détermination
du retrait
Plastics — Thermosetting moulding materials — Determination of
shrinkage




Numéro de référence
ISO 2577:2007(F)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 2577:2007(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2007
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2007 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 2577:2007(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 2577 a été élaborée par le comité technique ISO/TC 61, Plastiques, sous-comité SC 12, Matériaux
thermodurcissables.
Cette troisième édition annule et remplace la deuxième édition (ISO 2577:1984), qui a fait l'objet d'une
révision technique.

© ISO 2007 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 2577:2007(F)

Plastiques — Matières à mouler thermodurcissables —
Détermination du retrait
1 Domaine d'application
La présente Norme internationale spécifie une méthode de détermination du retrait de moulage et du retrait
après traitement thermique des éprouvettes moulées en matières à mouler thermodurcissables.
Ces caractéristiques sont utiles pour le contrôle de la production des matières thermodurcissables et la
vérification de l'uniformité de fabrication. En outre, la connaissance du retrait initial des matières
thermodurcissables est importante pour la construction des moules, et celle du post-retrait pour la
détermination de l'aptitude de la matière à mouler à la fabrication de pièces moulées de dimensions précises.
2 Références normatives
ISO 295, Plastiques — Moulage par compression des éprouvettes de matériaux thermodurcissables
ISO 10724-1, Plastiques — Moulage par injection d'éprouvettes en compositions de poudre à mouler (PMC)
thermodurcissables — Partie 1: Principes généraux et moulage d'éprouvettes à usages multiples
ISO 10724-2:1998, Plastiques — Moulage par injection d'éprouvettes en compositions de poudre à mouler (PMC)
thermodurcissables — Partie 2: Petites plaques
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s'appliquent.
3.1
retrait de moulage
différence de dimension entre une pièce moulée et l'empreinte du moule dans laquelle elle a été moulée, le
moule et la pièce étant tous les deux à la température ambiante normale lors du mesurage
3.2
post-retrait
retrait d'un produit plastique après moulage à l'occasion d'un post-traitement, d'un stockage ou d'une
utilisation
4 Appareillage
4.1 Moule, presse, etc., appropriés pour mouler les éprouvettes spécifiées à l'Article 6. Pour le moulage
par compression, un moule positif ou semi-positif à empreinte unique ou à empreintes multiples doit être
utilisé. Pour le moulage par injection, le moule de type D2 ISO doit être utilisé afin d'obtenir des éprouvettes
de dimensions 60 mm × 60 mm × 2 mm, conformément à l'ISO 10724-2:1998, Article 4.
Si nécessaire, des repères peuvent être gravés dans le moule près des extrémités des éprouvettes afin
d'améliorer la précision de la mesure de longueur de l'empreinte et des éprouvettes.
© ISO 2007 – Tous droits réservés 1

---------------------- Page: 4 ----------------------
ISO 2577:2007(F)
NOTE Si un moule positif à empreintes multiples est utilisé, les variations résultantes de la masse volumique des
éprouvettes peuvent être suffisantes pour produire des incohérences dans les résultats du retrait.
4.2 Équipement, approprié pour mesurer la longueur de l'éprouvette et de l'empreinte correspondante du
moule à 0,02 mm près.
4.3 Étuve (po
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.