EN ISO 10350-1:2017

Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)

The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. ISO 10350-1 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. For the purposes of ISO 10350-1, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
NOTE       ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics.

Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1: Formmassen (ISO 10350-1:2017)

Die Reihe ISO 10350 legt spezifische Prüfverfahren zur Ermittlung und Darstellung vergleichbarer Kennwerte für bestimmte grundlegende Eigenschaften von Kunststoffen fest. Im Allgemeinen wird jede Eigen¬schaft durch einen einzelnen Messwert festgelegt, in bestimmten Fällen wird eine Eigenschaft jedoch durch zwei Werte charakterisiert, die unter verschiedenen Prüfbedingungen ermittelt wurden. Die aufgeführten Eigenschaften werden vom Hersteller üblicherweise in Datenblättern erfasst. Dieser Teil der Reihe ISO 10350 behandelt in erster Linie thermoplastische und duroplastische Kunststoffe mit oder ohne Verstärkung, die spritzgegossen, gepresst oder in Form von Platten mit festgelegter Dicke bereitgestellt werden. ISO 10350 2 befasst sich speziell mit Kunststoffen, die eine Verstärkung durch lange oder kontinuierliche Fasern haben. Für die Anwendung von ISO 10350 gelten solche Kunststoffe als langfaserverstärkt, die vor dem Formen eine Faserlänge von mehr als 7,5 mm haben.

Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables - Partie 1: Matériaux pour moulage (ISO 10350-1:2017)

L'ISO 10350 identifie des méthodes d'essai spécifiques en vue de l'acquisition et de la présentation de données comparables relatives à certaines propriétés de base des matières plastiques. En général, chaque propriété est spécifiée par une valeur expérimentale unique; toutefois, dans certains cas, certaines propriétés sont représentées par deux valeurs obtenues dans des conditions d'essai différentes. Les propriétés indiquées sont celles qui sont traditionnellement présentées dans les fiches techniques des fabricants. L'ISO 10350-1 est avant tout applicable aux matériaux thermodurcissables ou thermoplastiques, renforcés ou non, susceptibles d'être moulés par compression ou injection ou préparés en feuilles ayant une épaisseur spécifiée. Pour les besoins du présent document, il est à noter que les plastiques renforcés de fibres longues ont des longueurs de fibre supérieures à 7,5 mm avant moulage.
NOTE       L'ISO 10350‑2 traite spécifiquement des plastiques renforcés de fibres longues ou continues.

Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih podatkov - 1. del: Materiali za oblikovanje (ISO 10350-1:2017)

Skupina standardov ISO 10350 določa posebne preskusne postopke za pridobitev in predstavitev primerljivih podatkov o določenih osnovnih lastnostih polimernih materialov. Na splošno vsako lastnost določa enotna eksperimentalna vrednost, čeprav so v nekaterih primerih lastnosti predstavljene z dvema vrednostma, ki sta pridobljeni pri različnih preskusnih pogojih. Vključene so tiste lastnosti, ki so običajno navedene v tehničnih listih proizvajalca. Ta dokument se večinoma uporablja za neojačene in ojačene plastomerne materiale in duromere, ki so lahko oblikovani z vbrizgavanjem ali stiskanjem oziroma so pripravljeni v obliki trakov določene debeline. Za potrebe tega dokumenta se za polimerne materiale, ojačene z dolgimi vlakni, šteje, da so njihova vlakna pred oblikovanjem daljša od 7,5 mm.
OPOMBA: Standard ISO 10350-2 obravnava zlasti z dolgimi ali neprekinjenimi vlakni ojačene polimerne materiale.

General Information

• Status: Published
• Publication Date: 28-Nov-2017
• Withdrawal Date: 30-May-2018
• ICS: 83.080.01 - Plastics in general
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 29-Nov-2017
• Completion Date: 29-Nov-2017
• Ref Project: SIST EN ISO 10350-1:2018 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)

Relations

• Replaces: EN ISO 10350-1:2008/A1:2014 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007/Amd 1:2014)
• Effective Date: 08-Jun-2022
• Replaces: EN ISO 10350-1:2008 - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007)
• Effective Date: 09-Dec-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10350-1:2018
01-februar-2018
1DGRPHãþD
SIST EN ISO 10350-1:2008
SIST EN ISO 10350-1:2008/A1:2014
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO0DWHULDOL]DREOLNRYDQMH,62
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding
materials (ISO 10350-1:2017)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1:
Formmassen (ISO 10350-1:2017)
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables -
Partie 1: Matériaux pour moulage (ISO 10350-1:2017)
Ta slovenski standard je istoveten z: EN ISO 10350-1:2017
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 10350-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10350-1:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 10350-1:2018


EN ISO 10350-1
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2017
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 10350-1:2008
English Version

Plastics - Acquisition and presentation of comparable
single-point data - Part 1: Moulding materials (ISO 10350-
1:2017)
Plastiques - Acquisition et présentation de Kunststoffe - Ermittlung und Darstellung
caractéristiques intrinsèques comparables - Partie 1: vergleichbarer Einpunktkennwerte - Teil 1:
Matériaux pour moulage (ISO 10350-1:2017) Formmassen (ISO 10350-1:2017)
This European Standard was approved by CEN on 10 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10350-1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10350-1:2018
EN ISO 10350-1:2017 (E)
Contents Page
European foreword . 3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 10350-1:2018
EN ISO 10350-1:2017 (E)
European foreword
This document (EN ISO 10350-1:2017) has been prepared by Technical Committee ISO/TC 61 “Plastics”
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be
withdrawn at the latest May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10350-1:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10350-1:2017 has been approved by CEN as EN ISO 10350-1:2017 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 10350-1:2018

---------------------
...