ISO 1420:2001

Rubber- or plastics-coated fabrics — Determination of resistance to penetration by water

Supports textiles revêtus de caoutchouc ou de plastique — Détermination de la résistance à la pénétration de l'eau

General Information

• Status: Withdrawn
• Publication Date: 18-Jul-2001
• Withdrawal Date: 18-Jul-2001
• ICS: 59.080.40 - Coated fabrics
• Technical Committee: ISO/TC 45/SC 4 - Products (other than hoses)
• Drafting Committee: ISO/TC 45/SC 4/WG 13 - Coated fabrics
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 23-Jun-2016

Relations

• Revised: ISO 1420:2016 - Rubber- or plastics-coated fabrics — Determination of resistance to penetration by water
• Effective Date: 17-Mar-2012
• Revises: ISO 1420:1987 - Rubber- or plastics-coated fabrics — Determination of resistance to penetration by water
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 1420
Third edition
2001-07-15
Rubber- or plastics-coated fabrics —
Determination of resistance to penetration
by water
Supports textiles revêtus de caoutchouc ou de plastique — Détermination
de la résistance à la pénétration de l'eau
Reference number
ISO 1420:2001(E)
©
ISO 2001

---------------------- Page: 1 ----------------------
ISO 1420:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 1420:2001(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Principle.1
4 Apparatus .1
5 Test specimens.2
6 Procedure .2
7 Expression of results .3
8 Test report .3
© ISO 2001 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 1420:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 1420 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 4, Products (other than hoses).
This third edition cancels and replaces the second edition (ISO 1420:1987), which has been technically revised.
iv © ISO 2001 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 1420:2001(E)
Rubber- or plastics-coated fabrics — Determination of resistance
to penetration by water
WARNING — Persons using this International Standard should be familiar with normal laboratory practice.
This standard does not purport to address all of the safety problems, if any, associated with its use. It is
the responsibility of the user to establish appropriate safety and health practices and to ensure compliance
with any national regulatory conditions.
1 Scope
This International Standard specifies a pass/fail method for the determination of the resistance of rubber- or
plastics-coated fabrics to water penetration (hydrostatic resistance) when subjected to a specific hydrostatic
pressure over a fixed period of time. Two test specimen shapes are given: one is circular, the other square.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most
...