ISO/IEC 16500-4:1999
(Main)Information technology — Generic digital audio-visual systems — Part 4: Lower-layer protocols and physical interfaces
Information technology — Generic digital audio-visual systems — Part 4: Lower-layer protocols and physical interfaces
This part of ISO/IEC 16500 provides a toolbox consisting of lower layer protocols and physical interfaces. Each tool is applicable at one or more of the reference points within the delivery system. The physical delivery media that have been identified for this version of ISO/IEC 16500-4 are copper pairs, coaxial cable, microwave, fiber and satellite. Removable information carrying physical media (e.g. optical discs and tapes) are not covered. The tools listed address the three parts of the delivery system, namely, the core network, the access network and the access-network-independent interface to the Set Top Unit (STU). Tools are also identified for the STU dataport interface and for a service provider system (SPS) internal network and an SPS/SPS core network. Clause 6 specifies in detail the tools provided to digitize the physical media in the core network. In the case of a broadband core network, all these tools support high speed ATM transport. Clause 7 specifies in detail the tools provided to digitize the physical media in the access network (copper pairs, coax, satellite, microwave, fiber). All these tools support high speed MPEG-2-TS transport and/or high speed ATM transport. Clause 8 concerns the access-network-independent interface to the STU and provides a detailed specification of the physical interfaces between the network interface unit (NIU) and the STU. This physical interface can be internal or external to the Set Top Box (STB) and is independent from the physical interface used in the access network. It supports the transport of MPEG-2-TS and ATM between NIU and STU. Clause 9 concerns the STU dataport interface and specifies the physical interfaces used to connect an STB to various peripheral devices. It defines normative STU multimedia dataport tools and interfaces and also includes informative specifications for both PC and parallel dataports. These interfaces support the transport of MPEG-2-TS or IP. Clause 10 defines the physical interfaces for interconnections between cascaded SPS entities with or without an intervening core network and the physical interfaces for networks used to connect various hosts within an SPS.
Technologies de l'information — Systèmes audiovisuels numériques génériques — Partie 4: Protocoles et interfaces physiques de la couche inférieure
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 16500-4
First edition
1999-12-15
Information technology — Generic digital
audio-visual systems —
Part 4:
Lower-layer protocols and physical
interfaces
Technologies de l'information — Systèmes audiovisuels numériques
génériques —
Partie 4: Protocoles et interfaces physiques de la couche inférieure
Reference number
ISO/IEC 16500-4:1999(E)
©
ISO/IEC 1999
---------------------- Page: 1 ----------------------
ISO/IEC 16500-4:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO/IEC 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO/IEC 1999 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 16500-4:1999(E)
Contents Page
Foreword .vi
Introduction . vii
1. Scope. 1
2. Normative references . 1
3. Definitions . 3
4. Acronyms and abbreviations . 6
5. Conventions . 8
6. Tools for Digitizing the Core network. 9
6.1 The Broadband Core network .9
6.2 The Narrowband Core network.9
7. Tools for Digitizing the Access network. 10
7.1 Low-Speed Symmetrical PHY on the PSTN .10
7.2 Low-Speed Symmetrical PHY on the ISDN.10
7.3 Low-Speed Symmetrical PHY on Public Land Mobile Networks .10
7.4 Long-Range Baseband Asymmetrical PHY on copper.11
7.5 Medium-Range Baseband Asymmetrical PHY on copper.11
7.6 Short-Range Baseband Asymmetrical PHY on copper and coax .12
7.6.1 Physical Medium Dependent (PMD) Sublayer Specification .12
7.6.2 Transmission Convergence (TC) PHY Sublayer Specification .34
7.7 Passband Unidirectional PHY on coax .50
7.7.1 Encoding/Decoding Process .50
7.7.2 MPEG-2 Transport Stream .52
7.7.3 Asynchronous Transfer Mode (ATM) Stream .52
7.7.4 Framing structure when carrying MPEG-2-TS.52
7.7.5 Framing structure when carrying ATM .53
7.7.6 High Reliability Marker (HRM) .55
7.7.7 Channel coding .56
7.7.8 Byte to symbol mapping .57
7.7.9 Quadrature Amplitude Modulation (QAM) .58
7.7.10 Baseband filter characteristics.62
7.7.11 Information Bit Rate .64
7.7.12 Coaxial Cable Impedance .64
7.7.13 Media Interface Connector.64
7.7.14 Inband Signaling for the Downstream QAM Link.65
7.8 Passband Bi-directional PHY on coax .70
7.8.1 Downstream Physical Interface Specification.71
7.8.2 Upstream Physical Interface Specification .82
© ISO/IEC 1999 - All rights reserved DAVIC 1.3.1a Part 8 (1999) iii
---------------------- Page: 3 ----------------------
ISO/IEC 16500-4:1999(E)
7.8.3 Media Access Control Functionality.89
7.8.4 Minislots.123
7.9 Passband Unidirectional PHY on Satellite .125
7.9.1 Satellite Downstream Transmission Specification.125
7.9.2 Interworking of Satellite and Coax Transmission (Informative).126
7.10 Passband Bi-directional PHY on MMDS .126
7.10.1 Downstream MMDS .126
7.10.2 Upstream MMDS.145
7.10.3 MAC Protocols and Scenarios .153
7.11 Passband PHY on LMDS.173
7.11.1 Downstream LMDS .173
7.11.2 Upstream LMDS .184
7.11.3 MAC Protocols and Scenarios .190
7.12 Baseband Symmetrical PHY on copper.211
7.13 Baseband Symmetrical PHY on fiber.211
7.14 Passband Unidirectional PHY for Mobile Reception .211
7.14.1 Encoding/Decoding Process.211
8. Network-Interface-Unit to Set-Top-Unit Interface. 212
8.1 Introduction to the A0 Interface. 212
8.2 Functional Description of the A0 Interface . 213
8.3 Capability Levels Required for A0.213
8.3.1 Notes on Requirements for Level “A” A0 Interface .214
8.3.2 Notes on Requirements for Level “B” A0 Interface.214
8.4 Definition of Internal and External A0 Interface.215
8.5 Specification of the Internal A0 (Digital Part).215
8.5.1 Electrical Specification .216
8.5.2 Physical and Mechanical Connector Specifications.221
8.6 Optional Internal A0 Specification (Analog Pass-Through Part).221
8.6.1 Electrical Specifications.221
8.6.2 Baseband Analog Video - Digitized Format .222
8.6.3 Baseband Analog Audio - Digitized Format.222
8.7 Optional Internal A0 Specification (Smart Card Bus).223
8.7.1 Electrical Connections When Not Implementing The Smart Card Bus .223
8.8 Physical Internal NIU Specifications. 225
8.8.1 User Replaceable Internal NIU Specifications:.225
8.8.2 Manufacturer Replaceable Internal NIU Specifications:.233
8.9 External A0 Specification (Digital Part).238
8.9.1 Electrical Specifications.239
8.9.2 Physical and Mechanical Specifications .241
8.10 Optional External A0 Specification (Analog Pass-Through Part).241
iv DAVIC 1.3.1a Part 8 (1999) © ISO/IEC 1999 - All rights reserved
---------------------- Page: 4 ----------------------
ISO/IEC 16500-4:1999(E)
9. STU Dataport Interface. 241
9.1 Overview of the STU Dataport .241
9.2 STU Multimedia Dataport.241
9.2.1 Physical Specification (PMD).242
9.2.2 Electrical Specification (PHY).242
9.2.3 Transmission Convergence Layer Specification (TC) .242
9.3 STU PC Dataport - INFORMATIVE Specification. .242
9.3.1 Physical Specification (PMD).242
9.3.2 Electrical Specification (PHY).242
9.3.3 Transmission Convergence Layer Specification (TC) .242
9.4 STU Parallel Dataport - INFORMATIVE Specification .242
10. Tools for digitizing the SPS/SPS core network and SPS internal networks 242
© ISO/IEC 1999 - All rights reserved DAVIC 1.3.1a Part 8 (1999) v
---------------------- Page: 5 ----------------------
ISO/IEC 16500-4:1999(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission)
form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC
participate in the development of International Standards through technical committees established by the
respective organization to deal with particular fields of technical activity. ISO and IEC technical committees
collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in
liaison with ISO and IEC, also take part in the work.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO/IEC 16500 may be the subject of
patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
International Standard ISO/IEC 16500-4 was prepared by DAVIC (Digital Audio-Visual Council) and was adopted,
under the PAS procedure, by Joint Technical Committee ISO/IEC JTC 1, Information technology, in parallel with its
approval by national bodies of ISO and IEC.
ISO/IEC 16500 consists of the following parts, under the general title Information technology — Generic digital
audio-visual systems:
� Part 1: System reference models and scenarios
� Part 2: System dynamics, scenarios and protocol requirements
� Part 3: Contours: Technology domain
� Part 4: Lower-layer protocols and physical interfaces
� Part 5: High and mid-layer protocols
� Part 6: Information representation
� Part 7: Basic security tools
� Part 8: Management architecture and protocols
� Part 9: Usage information protocols
vi DAVIC 1.3.1a Part 8 (1999) © ISO/IEC 1999 - All rights reserved
---------------------- Page: 6 ----------------------
ISO/IEC 16500-4:1999(E)
Introduction
ISO/IEC 16500 defines the minimum tools and dynamic behavior required by digital audio-visual systems for
end-to-end interoperability across countries, applications and services. To achieve this interoperability, it defines
the technologies and information flows to be used within and between the major components of generic digital
audio-visual systems. Interoperability between these components and between individual sub-systems is assured
through specification of tools and specification of dynamic systems behavior at defined reference points. A
reference point can comprise one or more logical (non-physical) information-transfer interfaces, and one or more
physical signal-transfer interfaces. A logical interface is defined by a set of information flows and associated
protocol stacks. A physical interface is an external interface and is fully defined by its physical and electrical
characteristics. Accessible reference points are used to determine and demonstrate compliance of a digital audio-
visual subsystem with this international standard.
A summary of each part follows.
ISO/IEC 16500-1 (DAVIC 1.3.1a Part 2) defines the normative digital audio-visual systems technical framework.
It provides a vocabulary and a Systems Reference Model, which identifies specific functional blocks and
information flows, interfaces and reference points.
ISO/IEC 16500-2 (DAVIC 1.3.1a Part 12) defines system dynamic behavior and physical scenarios. It details the
locations of the control functional entities along with the normative protocols needed to support the systems
behavior. It is structured as a set of protocol walk-throughs, or “Application Notes”, that rehearse both the steady
state and dynamic operation of the system at relevant reference points using specified protocols. Detailed
dynamics are given for the following scenarios: video on demand, switched video broadcast, interactive broadcast,
and internet access.
ISO/IEC 16500-3 (DAVIC 1.3.1a Part 14) provides the normative definition of DAVIC Technology Contours.
These are strict sets of Applications, Functionalities and Technologies which allow compliance and conformance
criteria to be easily specified and assessed. This part of ISO/IEC 16500 contains the full details of two contours.
These are the Enhanced Digital Broadcast (EDB) and Interactive Digital Broadcast (IDB). ISO/IEC 16500-3
specifies required technologies and is a mandatory compliance document for contour implementations.
ISO/IEC 16500-4 (DAVIC 1.3.1a Part 8) defines the toolbox of technologies used for lower layer protocols and
physical interfaces. The tools specified are those required to digitize signals and information in the Core Network
and in the Access Network. Each tool is applicable at one or more of the reference points specified within the
Delivery System. In addition a detailed specification is provided of the physical interfaces between the Network
Interface Unit and the Set Top Unit and of the physical interfaces used to connect Set Top Boxes to various
peripheral devices (digital video recorder, PC, printer). The physical Delivery System mechanisms included are
copper pairs, coaxial cable, fiber, HFC, MMDS, LMDS, satellite and terrestrial broadcasting.
ISO/IEC 16500-5 (DAVIC 1.3.1a Part 7) defines the technologies used for high and mid-layer protocols for
ISO/IEC 16500 digital audio-visual systems. In particular, this part defines the specific protocol stacks and
requirements on protocols at specific interfaces for the content, control and management information flows.
ISO/IEC 16500-6 (DAVIC 1.3.1a Part 9) defines what the user will eventually see and hear and with what quality.
It specifies the way in which monomedia and multimedia information types are coded and exchanged. This
includes the definition of a virtual machine and a set of APIs to support interoperable exchange of program code.
Interoperability of applications is achieved, without specifying the internal design of a set top unit, by a normative
Reference Decoder Model which defines specific memory and behavior constraints for content decoding. Separate
profiles are defined for different sets of multimedia components.
ISO/IEC 16500-7 (DAVIC 1.3.1a Part 10) defines the interfaces and the security tools required for an
ISO/IEC 16500 system implementing security profiles. These tools include security protocols which operate
across one or both of the defined conditional access interfaces CA0 and CA1. The interface CA0 is to all security
and conditional access functions, including the high speed descrambling functions. The interface CA1 is to a
tamper resistant device used for low speed cryptographic processing. This cryptographic processing function is
implemented in a smart card.
ISO/IEC 16500-8 (DAVIC 1.3.1a Part 6) specifies the information model used for managing ISO/IEC 16500
systems. In particular, this part defines the managed object classes and their associated characteristics for
managing the access network and service-related data in the Delivery System. Where these definitions are taken
from existing standards, full reference to the required standards is provided. Otherwise a full description is
integrated in the text of this part. Usage-related information model is defined in ISO/IEC 16500-9.
© ISO/IEC 1999 - All rights reserved DAVIC 1.3.1a Part 8 (1999) vii
---------------------- Page: 7 ----------------------
ISO/IEC 16500-4:1999(E)
ISO/IEC 16500-9 (DAVIC 1.3.1a Part 11) specifies the interface requirements and defines the formats for the
collection of usage data used for billing, and other business-related operations such as customer profile
maintenance. It also specifies the protocols for the transfer of Usage Information into and out of the
ISO/IEC 16500 digital audio-visual system. In summary, flows of audio, video and audio-visual works are
monitored at defined usage data collection elements (e.g. servers, elements of the Delivery System, set-top boxes).
Information concerning these flows is then collected, processed and passed to external systems such as billing or a
rights administration society via a standardised usage data transfer interface.
Additional Information
ISO/IEC TR 16501 is an accompanying Technical Report. Further architectural and conformance information is
provided in other non-normative parts of DAVIC 1.3.1a (1999). A summary of these documents is included here
for information.
ISO/IEC TR 16501 (DAVIC 1.3.1a Part 1) provides a detailed listing of the functionalities required by users and
providers of digital audio-visual applications and systems. It introduces the concept of a contour and defines the
IDB (Interactive Digital Broadcast) and EDB (Enhanced Digital Broadcast) functionality requirements which are
used to define the normative contour technology toolsets provided in ISO/IEC 16500-3.
DAVIC 1.3.1a Parts 3, 4 and 5 are DAVIC technical reports. They provide additional architectural and other
information for the server, the delivery-system, and the Service Consumer systems respectively. Part 3 defines
how to load an application, once created, onto a server and gives information and guidance on the protocols
transmitted from the set-top user to the server, and those used to control the set-up and execution of a selected
application. Part 4 provides an overview of Delivery Systems and describes instances of specific DAVIC
networked service architectures. These include physical and wireless networks. Non-networked delivery (e.g.
local storage physical media like discs, tapes and CD-ROMs) are not specified. Part 5 provides a Service
Consumer systems architecture and a description of the DAVIC Set Top reference points defined elsewhere in the
normative parts of the specification.
DAVIC 1.3.1a Part 13 is a DAVIC technical report, which provides guidelines on how to validate the systems,
technology tools and protocols through conformance and / or interoperability testing.
viii DAVIC 1.3.1a Part 8 (1999) © ISO/IEC 1999 - All rights reserved
---------------------- Page: 8 ----------------------
INTERNATIONAL STANDARD ©ISO/IEC ISO/IEC 16500-4:1999(E)
Information technology — Generic digital audio-visual systems —
Part 4: Lower layer protocols and physical interfaces
1. Scope
This part of ISO/IEC 16500 provides a toolbox consisting of lower layer protocols and physical interfaces. Each
tool is applicable at one or more of the reference points within the delivery system. The physical delivery media
that have been identified for this version of ISO/IEC 16500-4 are copper pairs, coaxial cable, microwave, fiber
and satellite. Removable information carrying physical media (e.g. optical discs and tapes) are not covered. The
tools listed address the three parts of the delivery system, namely, the core network, the access network and the
access-network-independent interface to the Set Top Unit (STU). Tools are also identified for the STU dataport
interface and for a service provider system (SPS) internal network and an SPS/SPS core network.
Clause 6 specifies in detail the tools provided to digitize the physical media in the core network. In the case of a
broadband core network, all these tools support high speed ATM transport. Clause 7 specifies in detail the tools
provided to digitize the physical media in the access network (copper pairs, coax, satellite, microwave, fiber). All
these tools support high speed MPEG-2-TS transport and/or high speed ATM transport. Clause 8 concerns the
access-network-independent interface to the STU and provides a detailed specification of the physical interfaces
between the network interface unit (NIU) and the STU. This physical interface can be internal or external to the
Set Top Box (STB) and is independent from the physical interface used in the access network. It supports the
transport of MPEG-2-TS and ATM between NIU and STU. Clause 9 concerns the STU dataport interface and
specifies the physical interfaces used to connect an STB to various peripheral devices. It defines normative STU
multimedia dataport tools and interfaces and also includes informative specifications for both PC and parallel
dataports. These interfaces support the transport of MPEG-2-TS or IP. Clause 10 defines the physical interfaces
for interconnections between cascaded SPS entities with or without an intervening core network and the physical
interfaces for networks used to connect various hosts within an SPS.
2. Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions
of this part of ISO/IEC 16500. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this part of ISO/IEC 16500 are encouraged to
investigate the possibility of applying the most recent editions of the standards indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards. The Telecommunication Standardization Bureau (TSB)
maintains a list of currently valid ITU-T Recommendations.
2.1 IEC, ISO, ISO/IEC and ITU-T normative references
IEC 60801–4:1988 Electromagnetic compatibility for industrial process measurement and control equipment.
Part 4: Electrical fast transient/burst requirements
IEC 61883-1:1998, Consumer audio/video equipment – Digital interface – Part 1: General.
IEC 61883-4:1998, Consumer audio/video equipment – Digital interface – Part 4: MPEG-2 TS data transmission.
ISO/IEC 7816-3:1989, Identification cards – Integrated circuit(s) cards with contacts – Part 3: Electronic signals
and transmission protocols.
ISO/IEC 8802-3:1996, Information technology - Telecommunications and information exchange between systems –
Local and metropolitan area networks – Specific requirements – Part3: Carrier sense multiple access with
collision detection (CSMA/CD) access method and physical layer specifications.
ISO/IEC 8877: 1987, Information technology – Telecommunications and information exchange between systems –
Interface connector and contact assignments for ISDN Basic Access Interface located at reference points S
and T.
ISO/IEC 11801:1995, Generic cabling for customer premises, standards for generic cabling for information
technology.
ISO/IEC 13818-1:1996, Information technology – Generic coding of moving pictures and associated audio
information: Systems
© ISO/IEC 1999 - All rights reserved DAVIC 1.3.1a Part 8 (1999) 1
---------------------- Page: 9 ----------------------
ISO/IEC 16500-4:1999(E)
ISO/IEC 13818-9:1996, Extension for real-time interface for systems decoders.
ITU General Secretariat, Radio Regulations (1990), Volume 1, Article 8, Frequency Allocations Chapter RR8.
ITU-R Recommendation 656. Recommendations of the ITU-R (formerly CCIR), 1990 -- CCIR 656, Part I.
ITU-T Recommendation G.117 [Blue Book], Transmission aspects of unbalance about earth (definitions and
methods), version CCITT PA 1988, published March 1990.
ITU-T Recommendation G.652 [Rev. 1], Characteristics of a single-mode optical fiber cable, version WTSC
1993, published February 1994.
ITU-T Recommendation G.704 [Rev. 2], Synchronous frame structures used at levels of 1544, 6312, 2048, 8448
and 44736 kbit/s, July 95.
ITU-T Recommendation G.707 [Rev. 2], Synchronous digital hierarchy bit rates, version WTSC 1993, published
August 1993.
ITU-T Recommendation G.708, [Rev. 2], Network node interface for synchronous digital hierarchy, version
WTSC 1993, published November 1993.
ITU-T Recommendation G.709 [Rev. 2], Digital transmission systems - Terminal Equipment - General, version
WTSC 1993, published December 1993.
ITU-T Recommendation G.804 [New], ATM cell mapping into plesiochronous digital hierarchy (PDH), version
November 1993, published October 1994.
ITU-T Recommendation G.832 (11/1995), Transport of SDH elements on PDH networks: Frame and
multiplexing structures.
ITU-T Recommendation G.957 (07/1995), Optical interfaces for equipment an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.