ISO 15223:2000/Amd 1:2002

Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied — Amendment 1

Dispositifs médicaux — Symboles à utiliser avec les étiquettes, l'étiquetage et les informations à fournir relatifs aux dispositifs médicaux — Amendement 1

General Information

• Status: Withdrawn
• Publication Date: 14-Aug-2002
• Withdrawal Date: 14-Aug-2002
• ICS: 01.080.99 - Other graphical symbols
• ICS: 11.040.01 - Medical equipment in general
• Technical Committee: ISO/TC 210 - Quality management and corresponding general aspects for medical devices
• Drafting Committee: ISO/TC 210/WG 3 - Symbols and nomenclature for medical devices
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 15-Jan-2010

Relations

• Revised: ISO 15223-1:2007 - Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied — Part 1: General requirements
• Effective Date: 15-Apr-2008
• Revised: ISO 15223-2:2010 - Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation
• Effective Date: 25-Sep-2010
• Amends: ISO 15223:2000 - Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied
• Effective Date: 06-Jun-2022
• Child: ISO 15223:2000 - Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 15223
First edition
2000-04-15
AMENDMENT 1
2002-08-01
Medical devices — Symbols to be used
with medical device labels, labelling and
information to be supplied
AMENDMENT 1
Dispositifs médicaux — Symboles à utiliser avec les étiquettes, l'étiquetage
et les informations à fournir relatifs aux dispositifs médicaux
AMENDEMENT 1




Reference number
ISO 15223:2000/Amd.1:2002(E)
©
 ISO 2002

---------------------- Page: 1 ----------------------
ISO 15223:2000/Amd.1:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland

ii © ISO 2002 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 15223:2000/Amd.1:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this Amendm
...