ISO 15830-3:2022/PRF Amd 1

Road vehicles — Design and performance specifications for the WorldSID 50th percentile male side-impact dummy — Part 3: Mechanical requirements for electronic subsystems — Amendment 1: Head triaxial linear accelerometer neutral axes

Véhicules routiers — Conception et spécifications de performance pour le mannequin mondial (WorldSID), 50e percentile homme, de choc latéral — Partie 3: Exigences mécaniques pour sous-systèmes électroniques — Amendement 1

General Information

• Status: Not Published
• ICS: 43.020 - Road vehicles in general
• Technical Committee: ISO/TC 22/SC 36 - Safety and impact testing
• Drafting Committee: ISO/TC 22/SC 36/WG 5 - Anthropomorphic test devices
• Current Stage: 5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
• Start Date: 24-Nov-2025
• Completion Date: 07-Dec-2025

Relations

• Amends: ISO 15830-3:2022 - Road vehicles — Design and performance specifications for the WorldSID 50th percentile male side-impact dummy — Part 3: Mechanical requirements for electronic subsystems
• Effective Date: 07-Jan-2025

Standards Content (Sample)

International
Standard
ISO 15830-3
Third edition
Road vehicles — Design and
2022-11
performance specifications for the
WorldSID 50th percentile male side-
AMENDMENT 1
impact dummy —
Part 3:
Mechanical requirements for
electronic subsystems
AMENDMENT 1: Head triaxial linear
accelerometer neutral axes
Véhicules routiers — Conception et spécifications de performance
pour le mannequin mondial (WorldSID), 50e percentile homme,
de choc latéral —
Partie 3: Exigences mécaniques pour sous-systèmes électroniques
AMENDEMENT 1
PROOF/ÉPREUVE
Reference number
ISO 15830-3:2022/Amd.1:2025(en) © ISO 2025

ISO 15830-3:2022/Amd.1:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
ii
ISO 15830-3:2022/Amd.1:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use o
...

ISO 15830-3:2022/DAMPRF Amd 1:2025(en)
ISO/TC 22/SC 36
Secretariat: AFNOR
Date: 2025-11-24
Road vehicles – — Design and performance specifications for the
WorldSID 50th percentile male side-impact dummy – —
Part 3:
Mechanical requirements for electronic subsystems
AMENDMENT 1: Head triaxial linear accelerometer neutral axes
Véhicules routiers — Conception et spécifications de performance pour le mannequin mondial (WorldSID), 50e
percentile homme, de choc latéral —
Partie 3: Exigences mécaniques pour sous-systèmes électroniques
AMENDEMENT 1
PROOF
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO 15830-3:2022/DAMPRF Amd 1:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementa
...