ISO 3601-4:2008

Fluid power systems — O-rings — Part 4: Anti-extrusion rings (back-up rings)

ISO 3601-4:2008 specifies dimensions and tolerances for five types of anti-extrusion rings, which are also known as back-up rings: spiral type (T1); angle cut type (T2); solid type (T3); angle cut concave type (T4); solid concave type (T5). These anti-extrusion rings are for use with selected O-ring sizes as specified in ISO 3601-1 and the relevant housing dimensions specified in ISO 3601-2.

Transmissions hydrauliques et pneumatiques — Joints toriques — Partie 4: Bagues anti-extrusion

General Information

• Status: Published
• Publication Date: 26-May-2008
• ICS: 23.100.60 - Filters, seals and contamination of fluids
• ICS: 83.140.50 - Seals
• Technical Committee: ISO/TC 131/SC 7 - Sealing devices
• Drafting Committee: ISO/TC 131/SC 7 - Sealing devices
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 13-Dec-2023

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3601-4
First edition
2008-06-01


Fluid power systems — O-rings —
Part 4:
Anti-extrusion rings (back-up rings)
Transmissions hydrauliques et pneumatiques — Joints toriques —
Partie 4: Bagues anti-extrusion




Reference number
ISO 3601-4:2008(E)
©
ISO 2008

---------------------- Page: 1 ----------------------
ISO 3601-4:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2008 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 3601-4:2008(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Symbols .2
5 General requirements related to O-ring housings .2
6 Types of anti-extrusion (back-up) rings .3
6.1 Spiral type, T1 .3
6.2 Angle cut type, T2.5
6.3 Solid type, T3.5
6.4 Angle cut concave type, T4 .6
6.5 Solid concave type, T5 .7
7 Positioning of anti-extrusion rings in housings.8
8 Anti-extrusion ring designation code and materials.8
8.1 Designation code.8
8.2 Materials .9
9 Dimensions and tolerances .9
9.1 Axial and radial widths of anti-extrusion rings.9
9.2 Outside diameters of anti-extrusion rings for piston sealing applications.10
9.3 Inside diameters of anti-extrusion rings for rod seali
...