ISO 17078-1:2004/Amd 1:2010
(Amendment)Petroleum and natural gas industries — Drilling and production equipment — Part 1: Side-pocket mandrels — Amendment 1
- BACK
- 02-Mar-2010
- 75.180.10
- ISO/TC 67/SC 4
Petroleum and natural gas industries — Drilling and production equipment — Part 1: Side-pocket mandrels — Amendment 1
Industries du pétrole et du gaz naturel — Équipement de forage et de production — Partie 1: Raccords à poche latérale — Amendement 1
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 17078-1
First edition
2004-12-15
AMENDMENT 1
2010-03-15
Petroleum and natural gas industries —
Drilling and production equipment —
Part 1:
Side-pocket mandrels
AMENDMENT 1
Industries du pétrole et du gaz naturel — Équipement de forage et de
production —
Partie 1: Raccords à poche latérale
AMENDEMENT 1
Reference number
ISO 17078-1:2004/Amd.1:2010(E)
©
ISO 2010
---------------------- Page: 1 ----------------------
ISO 17078-1:2004/Amd.1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 17078-1:2004/A
...
This May Also Interest You
This document specifies the requirements and recommendations for the design, setting depth and installation of conductors for the offshore petroleum and natural gas industries. This document specifically addresses: — design of the conductor, i.e. determination of the diameter, wall thickness, and steel grade; — determination of the setting depth for three installation methods, namely, driving, drilling and cementing, and jetting; — requirements for the three installation methods, including applicability, procedures, and documentation and quality control. This document is applicable to: — platform conductors: installed through a guide hole in the platform drill floor and then through guides attached to the jacket at intervals through the water column to support the conductor, withstand actions, and prevent excessive displacements; — jack-up supported conductors: a temporary conductor used only during drilling operations, which is installed by a jack-up drilling rig. In some cases, the conductor is tensioned by tensioners attached to the drilling rig; — free-standing conductors: a self-supporting conductor in cantilever mode installed in shallow water, typically water depths of about 10 m to 20 m. It provides sole support for the well and sometimes supports a small access deck and boat landing; — subsea wellhead conductors: a fully submerged conductor extending only a few metres above the sea floor to which a BOP and drilling riser are attached. The drilling riser is connected to a floating drilling rig. The BOP, riser and rig are subject to wave and current actions while the riser can also be subject to VIV. This document is not applicable to the design of drilling risers.
- Standard36 pagesEnglish languagesale 15% off
- Standard42 pagesFrench languagesale 15% off
- 05-Jun-2022
- 75.180.10
- ISO/TC 67/SC 4
This document specifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, and purchasing of wellhead and tree equipment for use in the petroleum and natural gas industries. This document does not apply to field use or field testing. This document does not apply to repair of wellhead and tree equipment except for weld repair in conjunction with manufacturing. This document does not apply to tools used for installation and service (e.g. running tools, test tools, wash tools, wear bushings, and lubricators). This document supplements API Spec 6A, 21st edition (2018), the requirements of which are applicable with the exceptions specified in this document.
- Standard4 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Draft4 pagesEnglish languagesale 15% off
- 07-Mar-2022
- 75.180.10
- ISO/TC 67/SC 4
This document specifies general safety requirements for the design, testing and production of powered elevators. The requirements are applicable for onshore and offshore applications of such elevators in the petroleum and petrochemical industries. This document does not cover any other type of elevator. It is not applicable to the following types of products: — remote control devices; — lifting nubbins; — lifting plugs; — lifting subs; — internal gripping devices; — equipment for lifting tubular from and onto a vessel; — elevator links or bails. This list is not exhaustive. This document is not applicable to powered elevators manufactured before the date of this publication. NOTE Annex A provides the relation between the clauses of the European Directive on machinery (Directive 2006/42/EC) and this document, for potential significant hazards and the safety requirements dealing with them for powered elevators.
- Standard25 pagesEnglish languagesale 15% off
- 11-Mar-2020
- 13.110
- 75.180.10
- ISO/TC 67/SC 4
ISO 18647:2017 gives requirements for the design, fabrication, installation, commissioning and integrity management of modular drilling rigs on offshore fixed platforms. The modular drilling rig includes some or all of the equipment as follows: - drilling equipment including a derrick/mast and its controls that can be moved by skidding a drilling support structure; - drilling support equipment which includes support facilities such as power supply/distribution system; - mud and cement storage, mixing, monitoring and control equipment. ISO 18647:2017 is applicable to the modular drilling equipment on offshore structures for the petroleum and natural gas industries, as follows: - new equipment arranged in a modularized form; - the equipment contained in several modules, each of which can be lifted and installed on to the platform, however, the equipment may be arranged within the modules as is convenient; - the modules assembled together offshore for hook up and commissioning; - intended for long term use on a new fixed offshore structure; - Intended for temporary use on a number of different offshore platforms. ISO 18647:2017 is not applicable to drilling equipment - installed on mobile offshore units, and - intended primarily for onshore use. ISO 18647:2017 does not apply to those parts and functions of an offshore platform that are not directly related to drilling.
- Standard113 pagesEnglish languagesale 15% off
- 20-Aug-2017
- 75.180.10
- ISO/TC 67/SC 4
ISO 16530-1:2017 is applicable to all wells that are operated by the petroleum and natural gas industry. This document is applicable to any well, or group of wells, regardless of their age, location (including onshore, subsea and offshore wells) or type (e.g. naturally flowing, artificial lift, injection wells). ISO 16530-1:2017 is intended to assist the petroleum and natural gas industry to effectively manage well integrity during the well life cycle by providing: - minimum requirements to ensure management of well integrity; and - recommendations and techniques that well operators can apply in a scalable manner based on a well's specific risk characteristics. Assuring well integrity comprises two main building blocks: the first is to ensure well integrity during well design and construction, and the second is to manage well integrity throughout the remaining well life thereafter. This document addresses each stage of the well life cycle, as defined by the six phases in a) to f), and describes the deliverables between each phase within a Well Integrity Management system. a) The "Basis of Design Phase" identifies the probable safety and environmental exposure to surface and subsurface hazards and risks that can be encountered during the well life cycle. Once identified, these hazards and risks are assessed such that control methods of design and operation can be developed in subsequent phases of the well life cycle. b) The "Design Phase" identifies the controls that are to be incorporated into the well design, such that appropriate barriers can be established to manage the identified safety and environmental hazards. The design addresses the expected, or forecasted, changes during the well life cycle and ensures that the required barriers in the well's design are based on risk exposure to people and the environment. c) The "Construction Phase" defines the required or recommended elements to be constructed (including rework/repair) and verification tasks to be performed in order to achieve the intended design. It addresses any variations from the design which require a revalidation against the identified hazards and risks. d) The "Operational Phase" defines the requirements or recommendations and methods for managing well integrity during operation. e) The "Intervention Phase" (including work-over) defines the minimum requirements or recommendations for assessing well barriers prior to, and after, any well intervention that involves breaking the established well barrier containment system. f) The "Abandonment Phase" defines the requirements or recommendations for permanently abandoning a well. The six phases of the well life cycle, as defined in this Scope, and their interrelationships, are illustrated in Figure 1 in the Introduction. ISO 16530-1:2017 is not applicable to well control. Well control refers to activities implemented to prevent or mitigate unintentional release of formation fluids from the well to its surroundings during drilling, completion, intervention and well abandonment operations, and involves dynamic elements, i.e. BOPs, mud pumps, mud systems, etc. ISO 16530-1:2017 is not applicable to wellbore integrity, sometimes referred to as "borehole stability". Wellbore integrity is the capacity of the drilled open hole to maintain its shape and remain intact after having been drilled.
- Standard124 pagesEnglish languagesale 15% off
- Standard132 pagesFrench languagesale 15% off
- 05-Mar-2017
- 75.180.10
- ISO/TC 67/SC 4
ISO 15551-1:2015 provides requirements for the design, design verification and validation, manufacturing and data control, performance ratings, functional evaluations, handling, and storage of tubing-deployed electrical submersible pump (ESP) systems as defined herein. This part of ISO 15551 is applicable to those components meeting the definition of centrifugal pumps including gas handling devices, discharge heads, seal chamber sections, intake systems, mechanical gas separators, induction motors (herein motor), shaft couplings, motor lead extension, pothead, and power cables, as defined herein. Components supplied under the requirements of this part of ISO 15551 exclude previously used subcomponents. Additionally, this International Standard provides requirements for assembled ESP systems. ISO 15551-1:2015 includes normative annexes addressing design validation performance rating requirements by component, requirements for determining ratings as an assembled system, functional evaluation: single component and cable reference information. ISO 15551-1:2015 includes informative annexes addressing functional evaluation guidelines for assembled ESP systems, establishing recommended operating range (ROR) of the ESP system, example user/purchaser ESP functional specification form, considerations for the use of 3-phase low and medium voltage adjustable speed drives for ESP applications, analysis after ESP use, downhole monitoring of ESP assembly operation, and information on permanent magnet motors for ESP applications. Equipment not covered by this part of ISO 15551 includes wireline and coiled tubing-deployed ESP systems, motor and pump shrouds, electric penetrators and feed-through systems, cable clamps and banding, centralizers, intake screens, passive gas separators, by-pass tools, check and bleeder valves, component adaptors, capillary lines, electric surface equipment, downhole permanent magnet motors, and non-conventionally configured ESP systems such as inverted systems. Repair and redress equipment requirements are not covered in this part of ISO 15551. The terminologies used within this part of ISO 15551 are; "ESP assembly" for a system of products combined into an operational machine, "component" for individual products such as, pumps or seal chamber sections, and "subcomponent" for individual parts or subassemblies that are used in the construction of an individual component.
- Standard121 pagesEnglish languagesale 15% off
- 05-May-2015
- 75.180.10
- ISO/TC 67/SC 4
ISO 13354:2014 specifies requirements for the selection of the diverter equipment for rigs used to drill shallow-gas-bearing formations. It covers both onshore and offshore drilling operations, and considers also the auxiliary equipment associated with floating rigs. The specified requirements concern the following diverter equipment: annular sealing devices; vent outlets; diverter valves; diverter piping. ISO 13554:2014 highlights the concerns associated with the selection of a marine floating drilling support. It covers safety issues concerning key rig equipment, and important steps of action required prior to starting the drilling operations. It provides only general guidelines regarding the response to be given to a shallow-gas flow.
- Standard41 pagesEnglish languagesale 15% off
- Standard41 pagesEnglish languagesale 15% off
- Standard41 pagesFrench languagesale 15% off
- 15-May-2014
- 75.180.10
- ISO/TC 67/SC 4
ISO 14998:2013 provides requirements and guidelines for completion accessories, as defined herein for use in the petroleum and natural gas industry. ISO 14998:2013 provides requirements for the functional specification and technical specifications including: design, design verification and validation, materials, documentation and data control, redress, repair, shipment, and storage. ISO 14998:2013 covers the pressure containing, load bearing, disconnect/reconnect, tubing movement, and opening a port functionalities of completion accessories.
- Standard43 pagesEnglish languagesale 15% off
- Standard43 pagesEnglish languagesale 15% off
- Standard49 pagesFrench languagesale 15% off
- 15-Jul-2013
- 75.180.10
- ISO/TC 67/SC 4
ISO 13628-15:2011 addresses recommendations for subsea structures and manifolds, within the frameworks set forth by recognized and accepted industry specifications and standards. As such, it does not supersede or eliminate any requirement imposed by any other industry specification. ISO 13628-15:2011 covers subsea manifolds and templates utilized for pressure control in both subsea production of oil and gas, and subsea injection services. The following equipment falls within the scope of ISO 13628-15:2011: structural components and piping systems of subsea production systems, including production and injection manifolds, modular and integrated single satellite and multiwell templates, subsea processing and subsea boosting stations, flowline riser bases and export riser bases (FRB, ERB), pipeline end manifolds (PLEM), pipeline end terminations (PLET), T- and Y-connection, and subsea isolation valve (SSIV); structural components of subsea production system, including subsea controls and distribution structures and other subsea structures, and protection structures associated with the above. ISO 13628-15:2011 is not applicable to pipeline and manifold valves, flowline and tie-in connectors, choke valves and production control systems.
- Standard63 pagesEnglish languagesale 15% off
- Standard65 pagesFrench languagesale 15% off
- 14-Sep-2011
- 75.180.10
- ISO/TC 67/SC 4
ISO 13628-4:2010 provides specifications for subsea wellheads, mudline wellheads, drill-through mudline wellheads and both vertical and horizontal subsea trees. It specifies the associated tooling necessary to handle, test and install the equipment. It also specifies the areas of design, material, welding, quality control (including factory acceptance testing), marking, storing and shipping for both individual sub-assemblies (used to build complete subsea tree assemblies) and complete subsea tree assemblies. The user is responsible for ensuring subsea equipment meets any additional requirements of governmental regulations for the country in which it is installed. This is outside the scope of ISO 13628-4:2010. Where applicable, ISO 13628-4:2010 can also be used for equipment on satellite, cluster arrangements and multiple well template applications. Equipment that is within the scope of ISO 13628-4:2010 is listed as follows: subsea trees: tree connectors and tubing hangers, valves, valve blocks, and valve actuators, chokes and choke actuators, bleed, test and isolation valves, TFL wye spool, re-entry interface, tree cap, tree piping, tree guide frames, tree running tools, tree cap running tools, tree mounted flowline/umbilical connector, tubing heads and tubing head connectors, flowline bases and running/retrieval tools, tree mounted controls interfaces (instrumentation, sensors, hydraulic tubing/piping and fittings, electrical controls cable and fittings); subsea wellheads: conductor housings, wellhead housings, casing hangers, seal assemblies, guidebases, bore protectors and wear bushings, corrosion caps; mudline suspension systems: wellheads, running tools, casing hangers, casing hanger running tool, tieback tools for subsea completion, subsea completion adaptors for mudline wellheads, tubing heads, corrosion caps; drill through mudline suspension systems: conductor housings, surface casing hangers, wellhead housings, casing hangers, annulus seal assemblies, bore protectors and wear bushings, abandonment caps; tubing hanger systems: tubing hangers, running tools; miscellaneous equipment: flanged end and outlet connections, clamp hub-type connections, threaded end and outlet connections, other end connections, studs and nuts, ring joint gaskets, guideline establishment equipment. ISO 13628-4:2010 includes equipment definitions, an explanation of equipment use and function, an explanation of service conditions and product specification levels, and a description of critical components, i.e. those parts having requirements specified in ISO 13628-4:2010. The following equipment is outside the scope of ISO 13628-4:2010: subsea wireline/coiled tubing BOPs; installation, workover, and production risers; subsea test trees (landing strings); control systems and control pods; platform tiebacks; primary protective structures; subsea process equipment; subsea manifolding and jumpers; subsea wellhead tools; repair and rework; multiple well template structures; mudline suspension high pressure risers; template piping; template interfaces. ISO 13628-4:2010 is not applicable to the rework and repair of used equipment.
- Standard100 pagesEnglish languagesale 15% off
- Standard251 pagesEnglish languagesale 15% off
- Standard251 pagesEnglish languagesale 15% off
- Standard265 pagesFrench languagesale 15% off
- Standard265 pagesFrench languagesale 15% off
- 12-Dec-2010
- 75.180.10
- ISO/TC 67/SC 4
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.