ISO 7364:2016
(Main)Ships and marine technology — Deck machinery — Accommodation ladder winches
Ships and marine technology — Deck machinery — Accommodation ladder winches
ISO 7364:2016 specifies requirements and characteristics of ships' accommodation ladder winches provided with hydraulic, pneumatic, electric or manual drive. ISO 7364:2016 is applicable to the design and test of accommodation ladder winches. ISO 7364:2016 does not include requirements for the prime mover used to operate the winch.
Navires et technologie maritime — Auxiliaires de pont — Treuils pour échelles de coupée
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 7364
Second edition
2016-04-01
Ships and marine technology — Deck
machinery — Accommodation ladder
winches
Navires et technologie maritime — Auxiliaires de pont — Treuils pour
échelles de coupée
Reference number
ISO 7364:2016(E)
©
ISO 2016
---------------------- Page: 1 ----------------------
ISO 7364:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7364:2016(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Design and operation . 2
5 Characteristics . 3
6 Acceptance tests (individual) . 4
6.1 General . 4
6.2 Test without load (factory test) . 4
6.3 Drum load test (factory test) . 4
6.4 Static test under 1,5 holding load . 5
6.5 On board test and inspections . 5
7 Designation . 5
© ISO 2016 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 7364:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee
SC 1, Lifesaving and fire protection.
This second edition cancels and replaces the first edition (ISO 7364:1983), which has been technically
revised.
iv © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 7364:2016(E)
Ships and marine technology — Deck machinery —
Accommodation ladder winches
1 Scope
This International Standard specifies requirements and characteristics of ships’ accommodation ladder
winches provided with hydraulic, pneumatic, electric or manual drive.
This International Standard is applicable to the design and test of accommodation ladder winches.
This International Standard does not include requirements for the prime mover used to operate the winch.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 2408, Steel wire ropes for general purposes — Minimum requirements
ISO 3828, Shipbuilding and marine structures — Deck machinery — Vocabulary and symbols
ISO 5488:2015, Ships and marine technology — Accommodation ladders
IEC 60092-401, Electrical installations in ships — Part 401: Installation and test of completed installation
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3828 and the following apply.
3.1
nominal size
used as a designation of a winch in accordance with this International Standard
Note 1 to entry: The nominal size corresponds to the drum load as given in Table 1.
3.2
drum load
maximum rope tension in the rope or ropes at the drum exit either when the winch is hoisting an
unloaded accommodation ladder at the nominal speed, with the rope or ropes wound on the drum in a
single layer, or when the winch is placing the accommodation ladder in its stowage position
3.3
holding load
in static mode of the winch, the maximum rope tension in the rope or ropes at the drum exit in a single
layer, shall be at least three times the drum load (3.2)
3.4 Types of winches
3.4.1
right-hand winch
winch where the reduction gear or drive of the drum is on the right-hand side of the drum, in relation to
an observer situated on the side of the motor or power supply
Note 1 to entry: See Figur
...
INTERNATIONAL ISO
STANDARD 7364
Second edition
Ships and marine tecnhology — Deck
machinery — Accommodation ladder
winches
Navires et technologie maritime — Auxiliaires de pont — Treuils pour
échelles de coupée
PROOF/ÉPREUVE
Reference number
ISO 7364:2016(E)
©
ISO 2016
---------------------- Page: 1 ----------------------
ISO 7364:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7364:2016(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Design and operation . 2
5 Characteristics . 4
6 Acceptance tests (individual) . 4
6.1 Test without load (factory test) . 4
6.2 Drum load test (factory test) . 5
6.3 Static test under 1,5 holding load . 5
6.4 On board test and inspections . 5
7 Designation . 5
© ISO 2016 – All rights reserved PROOF/ÉPREUVE iii
---------------------- Page: 3 ----------------------
ISO 7364:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 8, Ships and marine technology, Subcommittee
SC 1, Lifesaving and fire protection.
This second edition cancels and replaces the first edition (ISO 7364:1983), which has been
technically revised.
iv PROOF/ÉPREUVE © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 7364:2016(E)
Ships and marine tecnhology — Deck machinery —
Accommodation ladder winches
1 Scope
This International Standard specifies requirements and characteristics of ships’ accommodation ladder
winches provided with hydraulic, pneumatic, electric or manual drive.
This International Standard is applied to the design and test of accommodation ladder winches.
This International Standard does not include requirements for the prime mover used to operate the winch.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 2408, Steel wire ropes for general purposes — Minimum requirements
ISO 3828, Shipbuilding and marine structures — Deck machinery — Vocabulary and symbols
ISO 5488:2015, Ships and marine technology — Accommodation ladders
IEC 60092-401, Electrical installations in ships — Part 401: Installation and test of completed installation
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3828 and the following apply.
3.1
nominal size
used as a designation of a winch in accordance with this International Standard
Note 1 to entry: The nominal size corresponds to the drum load as given in Table 1.
3.2
drum load
maximum rope tension in the rope or ropes at the drum exit either when the winch is hoisting an
unloaded accommodation ladder at the nominal speed, with the rope or ropes wound on the drum in a
single layer, or when the winch is placing the accommodation ladder in its stowage position
3.3
holding load
in static mode of the winch, the maximum rope tension in the rope or ropes at the drum exit in a single
layer, shall be at least three times the drum load (3.2)
3.4 Types of winches
3.4.1
right-hand winch
winch where the reduction gear or drive of the drum is on the right-hand side of the drum, in relation to
an observer situated on the side of the motor or power supply
Note 1 to entry: See Figure 1.
© ISO 2016 – All rights reserved PROOF/ÉPREUVE 1
---------------------- Page: 5 ----------------------
ISO 7364:2016(E)
3.4.2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.