ISO/DIS 4548-6
(Main)Methods of test for full-flow lubricating oil filters for internal combustion engines
Methods of test for full-flow lubricating oil filters for internal combustion engines
Méthodes d'essai des filtres à huile de lubrification à passage intégral pour moteurs à combustion interne
General Information
RELATIONS
Buy Standard
Standards Content (sample)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 4548-6
ISO/TC 70/SC 7 Secretariat: BSI
Voting begins on: Voting terminates on:
2020-07-28 2020-10-20
Methods of test for full-flow lubricating oil filters for
internal combustion engines —
Part 6:
Static burst pressure test
Méthodes d'essai des filtres à huile de lubrification à passage intégral pour moteurs à combustion
interne —Partie 6: Essai de pression d'éclatement statique
ICS: 27.020
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
This document is circulated as received from the committee secretariat.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 4548-6:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 1 ----------------------
ISO/DIS 4548-6:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DIS 4548-6:2020(E)
Contents Page
Foreword ........................................................................................................................................................................................................................................iv
Introduction ..................................................................................................................................................................................................................................v
1 Scope ................................................................................................................................................................................................................................. 1
2 Normative references ...................................................................................................................................................................................... 1
3 Terms and definitions ..................................................................................................................................................................................... 1
4 Test rig ............................................................................................................................................................................................................................. 1
5 Test fluid ........................................................................................................................................................................................................................ 2
6 Preparation and test procedure ........................................................................................................................................................... 2
6.1 Verification that filter meets technical requirements ........................................................................................... 2
6.2 Determination of the filter failing pressure ................................................................................................................... 3
7 Report of test results ........................................................................................................................................................................................ 3
Bibliography ................................................................................................................................................................................................................................ 5
© ISO 2020 – All rights reserved iii---------------------- Page: 3 ----------------------
ISO/DIS 4548-6:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see w w w .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see w w w .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w .iso .org/ iso/ foreword .html.ISO 4548‐6 was prepared by Technical Committee ISO/TC 70, Internal combustion engines, Subcommittee
SC 7, Tests for lubricating oil filters.This third edition cancels and replaces the second edition (ISO 4548‐6:2012), which has been technically
revised. The main changes in the third edition are as follows:— The Verification that filter meet technical requirements and the determination of the filter failing
pressure have been separated into sections 6.1 and 6.2, respectively.— The first pressure increment in the verification has been specified with a known value.
— Each incremental pressure has been changed to the smaller value...
PROJET DE NORME INTERNATIONALE
ISO/DIS 4548-6
ISO/TC 70/SC 7 Secrétariat: BSI
Début de vote: Vote clos le:
2020-07-28 2020-10-20
Méthodes d'essai des filtres à huile de lubrification à
passage intégral pour moteurs à combustion interne —
Partie 6:
Essai de pression statique d’éclatement
Methods of test for full-flow lubricating oil filters for internal combustion engines —
Part 6: Static burst pressure testICS: 27.020
CE DOCUMENT EST UN PROJET DIFFUSÉ POUR
OBSERVATIONS ET APPROBATION. IL EST DONC
SUSCEPTIBLE DE MODIFICATION ET NE PEUT
ÊTRE CITÉ COMME NORME INTERNATIONALE
AVANT SA PUBLICATION EN TANT QUE TELLE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES
FINS INDUSTRIELLES, TECHNOLOGIQUES ET
COMMERCIALES, AINSI QUE DU POINT DE VUE
Le présent document est distribué tel qu’il est parvenu du secrétariat du comité.
DES UTILISATEURS, LES PROJETS DE NORMESINTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR
POSSIBILITÉ DE DEVENIR DES NORMES
POUVANT SERVIR DE RÉFÉRENCE DANS LA
RÉGLEMENTATION NATIONALE.
Numéro de référence
LES DESTINATAIRES DU PRÉSENT PROJET
ISO/DIS 4548-6:2020(F)
SONT INVITÉS À PRÉSENTER, AVEC LEURS
OBSERVATIONS, NOTIFICATION DES DROITS
DE PROPRIÉTÉ DONT ILS AURAIENT
ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE. ISO 2020
---------------------- Page: 1 ----------------------
ISO/DIS 4548-6:2020(F)
ISO/DIS 4548-6:2020(F)
Sommaire Page
Avant-propos ................................................................................................................................................................. iv
Introduction ..................................................................................................................................................................... v
1 Domaine d’application ................................................................................................................................... 1
2 Références normatives .................................................................................................................................. 1
3 Termes et définitions ..................................................................................................................................... 1
4 Banc d’essai ........................................................................................................................................................ 1
5 Fluide d’essai ..................................................................................................................................................... 2
6 Préparation de l’essai et mode opératoire ............................................................................................. 3
6.1 Vérifier si le filtre satisfait aux exigences techniques ........................................................................ 3
6.2 Déterminer la pression de défaillance du filtre ................................................................................... 3
7 Rapport d’essai ................................................................................................................................................. 4
Bibliographie ................................................................................................................................................................... 5
DOCUMENT PROTÉGÉ PAR COPYRIGHT© ISO 2020
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en oeuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright officeCase postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Website: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés
© ISO 2020 – Tous droits réservés
iii
---------------------- Page: 2 ----------------------
ISO/DIS 4548-6:2020(F)
Sommaire Page
Avant-propos ................................................................................................................................................................. iv
Introduction ..................................................................................................................................................................... v
1 Domaine d’application ................................................................................................................................... 1
2 Références normatives .................................................................................................................................. 1
3 Termes et définitions ..................................................................................................................................... 1
4 Banc d’essai ........................................................................................................................................................ 1
5 Fluide d’essai ..................................................................................................................................................... 2
6 Préparation de l’essai et mode opératoire ............................................................................................. 3
6.1 Vérifier si le filtre satisfait aux exigences techniques ........................................................................ 3
6.2 Déterminer la pression de défaillance du filtre ................................................................................... 3
7 Rapport d’essai ................................................................................................................................................. 4
Bibliographie ................................................................................................................................................................... 5
© ISO 2020 – Tous droits réservésiii
---------------------- Page: 3 ----------------------
ISO/DIS 4548-6:2020(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le
droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet
de droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour
responsable de ne pas avoir identifié de tels droits de propriété et averti de leur existence.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet
de droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour
responsable de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails
concernant les références aux droits de propriété intellectuelle ou autres droits analogues identifiés
lors de l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations
de brevets reçues par l'ISO (voir www.iso.org/brevets).Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www.iso.org/iso/avant-propos.html.
L’ISO 4548-6 a été élaborée par le Comité technique ISO/TC 70, Moteurs à combustion interne,
sous-comité SC 7, Essais des filtres à huile.Cette troisième édition annule et remplace la deuxième édition (ISO 4548-6:2012), qui a fait l’objet
d’une révision technique. Les principales modifications apportées dans la troisième édition sont les
suivantes :— La vérification visant à établir que le filtre est conforme aux exigences techniques
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.