ISO 1161:1984/Amd 1:2007
(Amendment)Series 1 freight containers — Corner fittings — Specification — Amendment 1: 45 ft containers
Series 1 freight containers — Corner fittings — Specification — Amendment 1: 45 ft containers
Conteneurs de la série 1 — Pièces de coin — Spécifications — Amendement 1: Conteneurs 45 ft
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 1161
Fourth edition
1984-12-15
AMENDMENT 1
2007-07-01
Series 1 freight containers — Corner
fittings — Specification
AMENDMENT 1: 45 ft containers
Conteneurs de la série 1 — Pièces de coin — Spécifications
AMENDEMENT 1: Conteneurs 45 ft
Reference number
ISO 1161:1984/Amd.1:2007(E)
©
ISO 2007
---------------------- Page: 1 ----------------------
ISO 1161:1984/Amd.1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 1161:1984/Amd.1:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 1161:1984 was prepared by Technical Committee ISO/TC 104, Freight containers,
Subcommittee SC 1, General purpose containers. The purpose of this amendment is to include 45 ft
containers in ISO 1161:1984.
© ISO 2007 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 1161:1984/Amd.1:2007(E)
Series 1 freight containers — Corner fittings — Specification
AMENDMENT 1: 45 ft containers
Page 2, subclause 3.1.1
Add the following after paragraph 2:
Apart from the above, 45 ft containers shall have four top intermediate fittings in the 40 ft position [see
Figures 1a) and 2a)] and four bottom intermediate fittings in the 40 ft position [see Figures 3a) and 4a)].
Page 2, subclause 3.2.4
Replace the first line by the following, to include “intermediate fittings”:
Where a corner or intermediate fitting has an optional inner side wall …
Page 2, Clause 4 Strength requirements
Replace the first line by the following, to include “intermediate fittings”:
The corner or intermediate fittings shall …
Page 2, 5.1 Loads
Replace the first paragraph by the following, to include “intermediate fittings”:
The following container design loads and criteria were used in establishing the dimensional design of
corner or intermediate fittings specified in this International Standard.
Replace the second paragraph by the following, to include “intermediate fittings” and “1EEE and 1 EE”:
Corner and intermediate fittings for series 1 freight containers shall be capable of withstanding the loads
calculated in accordance with the requirements of ISO 1496-1 for 1AA, 1A, 1AX, 1EEE and 1EE
containers.
Page 2, 5.1.1 Stacking
Replace “Top corner fitting [superimposed load offset …]” by
Top corner or intermediate fitting [superimposed load offset …]
Replace “Bottom corner fitting (resting on flat support)” by
Bottom corner or intermediate fitting (resting on flat support)
Replace “Bottom corner fitting [of No. 5 container offset …]” by
Bottom corner or intermediate fitting [of No. 5 container offset …]
© ISO 2007 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO 1161:1984/Amd.1:2007(E)
Page 2, 5.1.2 Lifting
Replace “Top corner fitting [twistlock …]” by
Top corner or intermediate fitting [twistlock …]
Replace “Bottom corner fitting:” by
Bottom corner or intermediate fitting:
Replace the fir
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.