SIST EN 747-1:2012
(Main)Furniture - Bunk beds and high beds - Part 1: Safety, strength and durability requirements
Furniture - Bunk beds and high beds - Part 1: Safety, strength and durability requirements
This European Standard specifies requirements for the safety, strength and durability of bunk beds and high beds for domestic and non-domestic use. The loads and forces in the strength and durability tests apply to beds with an internal length greater than 140 cm and a maximum bed base width of 120 cm. The dimensional requirements are intended to minimise the risk of accidents, particularly to children. The strength and durability requirements are intended to represent use by one occupant per bed. Safety requirements for other products included in a bunk bed/high bed, for example a table or storage furniture, are not included in this standard.
Möbel - Etagenbetten und Hochbetten - Teil 1: Anforderungen an die Sicherheit, Festigkeit und Dauerhaltbarkeit
Diese Europäische Norm legt Anforderungen an die Sicherheit, Festigkeit und Dauerhaltbarkeit von Etagenbetten und Hochbetten fest. Die für die Festigkeits und Dauerhaltbarkeitsprüfungen festgelegten Belastungen und Kräfte gelten für Betten mit einer inneren Länge von mehr als 140 cm und einer Höchstbreite des Bettbodens von 120 cm.
Durch die Maßanforderungen ist insbesondere beabsichtigt, die Unfallgefahr für Kinder auf ein Mindestmaß zu reduzieren.
Die Anforderungen an die Festigkeit und die Dauerhaltbarkeit sollen die Benutzung durch eine Person je Bett repräsentieren.
Sicherheitsanforderungen für andere Produkte, die bei einem Etagenbett/Hochbett mit enthalten sind, z. B. ein Tisch oder ein Behältnismöbel, sind nicht Gegenstand der vorliegenden Norm.
Dieses Dokument gilt nicht für Etagenbetten und Hochbetten für besondere Zwecke, einschließlich, aber nicht begrenzt auf Gefängnisse, Kasernen und Feuerwachen.
Meubles - Lits superposés et lits surélevés - Partie 1: Exigences de sécurité, de résistance et de durabilité
La présente Norme européenne spécifie les exigences relatives à la sécurité, la résistance et la durabilité des lits superposés et des lits surélevés. Les charges et forces spécifiées dans les essais de résistance et de durabilité s’appliquent aux lits de longueur interne supérieure à 140 cm et dont le sommier à une largeur maximale de 120 cm.
Les exigences dimensionnelles visent essentiellement à minimiser le risque d’accidents pour les enfants.
Les exigences de résistance et de durabilité sont basées exclusivement sur un usage d’une personne par lit.
Les exigences de sécurité relatives aux autres articles inclus dans un lit superposé/surélevé (table ou meuble de rangement, par exemple) ne sont pas indiquées dans la présente norme.
La présente Norme européenne ne s’applique pas aux lits superposés et lits surélevés à usage spécial, notamment ceux destinés à être utilisés en environnement carcéral ou militaire, ou à usage du corps des sapeurs-pompiers.
Pohištvo - Pogradi in visoke postelje - 1. del: Zahteve za varnost, trdnost in trajnost
Ta evropski standard določa zahteve za varnost, trdnost in trajnost pogradov in visokih postelj za domačo in javno rabo. Obremenitve in sile v preskusih trdnosti in trajnosti veljajo za postelje, katerih notranja dolžina presega 140 cm in pri katerih širina osnove meri 120 cm. Namen zahtev za mere je zmanjšati tveganje za nesreče, zlasti pri otrocih. Pri zahtevah glede trdnosti in trajnosti se predvideva, da posteljo uporablja ena oseba. Varnostne zahteve za druge izdelke, ki so del pograda/visoke postelje, npr. miza ali shranjevalno pohištvo, niso vključene v tem standardu.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Pohištvo - Pogradi in visoke postelje - 1. del: Zahteve za varnost, trdnost in trajnostMöbel - Etagenbetten und Hochbetten - Teil 1: Anforderungen an die Sicherheit, Festigkeit und DauerhaltbarkeitMeubles - Lits superposés et lits surélevés - Partie 1: Exigences de sécurité, de résistance et de durabilitéFurniture - Bunk beds and high beds - Part 1: Safety, strength and durability requirements97.140PohištvoFurnitureICS:Ta slovenski standard je istoveten z:EN 747-1:2012SIST EN 747-1:2012en,fr,de01-november-2012SIST EN 747-1:2012SLOVENSKI
STANDARDSIST EN 747-1:2007SIST EN 13453-1:20041DGRPHãþD
SIST EN 747-1:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 747-1
April 2012 ICS 97.140 Supersedes EN 13453-1:2004, EN 747-1:2007English Version
Furniture - Bunk beds and high beds - Part 1: Safety, strength and durability requirements
Meubles - Lits superposés et lits surélevés - Partie 1: Exigences de sécurité, de résistance et de durabilité
Möbel - Etagenbetten und Hochbetten - Teil 1: Anforderungen an die Sicherheit, Festigkeit und Dauerhaltbarkeit This European Standard was approved by CEN on 8 March 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 747-1:2012: ESIST EN 747-1:2012
EN 747-1:2012 (E) 2 Contents Page Foreword .3Introduction .41 Scope .52 Normative references .53 Terms and definitions .54 Safety requirements .64.1 Construction .64.1.1 General .64.1.2 Accessible holes gaps and openings .74.1.3 Bed base(s) .84.1.4 Safety barriers .84.1.5 Ladder or other means of access .9 Strength of ladder or other means of access - . 104.2 Attachment, deflection and strength . 104.3 Strength of frame and fastenings . 104.4 Stability . 104.5 Fastening of the upper bed to the lower bed . 105 Instructions for use . 116 Marking . 12 SIST EN 747-1:2012
EN 747-1:2012 (E) 3 Foreword This document (EN 747-1:2012) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2012, and conflicting national standards shall be withdrawn at the latest by October 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 747-1:2007 and EN 13453-1:2004. Compared to EN 747-1:2007 and EN 13453-1:2004, the following modifications have been made:
Subclause 4.1.1 General includes 4 options for protruding parts depending on the sizes of the part.
EN 747 is divided into the following parts: EN 747-1, Furniture — Bunk beds and high beds — Part 1: Safety, strength and durability requirements; EN 747-2, Furniture — Bunk beds and high beds — Part 2: Test methods. It should be noted that the changes made to
Part 2 are of importance for Part 1 because information regarding loads and forces is contained in Part 2. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 747-1:2012
EN 747-1:2012 (E) 4 Introduction This part of EN 747 specifies requirements for bunk beds and high beds for use by one occupant per bed. SIST EN 747-1:2012
EN 747-1:2012 (E) 5 1 Scope This European Standard specifies requirements for the safety, strength and durability of bunk beds and high beds for domestic and non-domestic use. The loads and forces in the strength and durability tests apply to beds with an internal length greater than 140 cm and a maximum bed base width of 120 cm. The dimensional requirements are intended to minimise the risk of accidents, particularly to children. The strength and durability requirements are intended to represent use by one occupant per bed. Safety requirements for other products included in a bunk bed/high bed, for example a table or storage furniture, are not included in this standard. This European Standard does not apply to bunk beds and high beds used for special purposes, including but not limited to prison, the military and fire brigades. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 747-2:2012, Furniture Bunk beds and high beds Part 2: Test methods 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 bunk bed set of components that can be assembled as beds, one above the other, where the upper surface of the top bed base is 800 mm or more above the floor 3.2 high bed set of components that can be assembled as a bed, where the upper surface of the top bed base is 800 mm or more above the floor, irrespective of the use to which the space below is put
3.3 bed end structures upright unit at the head and foot of the bed to which the side rails are attached 3.4 bed base support structure for a mattress 3.5 safety barrier component intended to prevent an occupant from falling out of the upper bed or the high bed 3.6 side rail longitudinal member attached to the bed end structure by which the bed base can be supported SIST EN 747-1:2012
EN 747-1:2012 (E) 6 3.7 tread structure intended as a foothold, including ladder rungs and steps 4 Safety requirements 4.1 Construction 4.1.1 General Accessible edges and corners shall
...
SLOVENSKI STANDARD
oSIST prEN 747-1:2010
01-junij-2010
Pohištvo - Pogradi in visoke postelje - 1. del: Zahteve za varnost, trdnost in
trajnost
Furniture - Bunk beds and high beds - Part 1: Safety, strength and durability
requirements
Möbel - Etagenbetten und Hochbetten - Teil 1: Anforderungen an die Sicherheit,
Festigkeit und Dauerhaltbarkeit
Meubles - Lits superposés et lits surélevés - Partie 1: Exigences de sécurité, de
résistance et de durabilité
Ta slovenski standard je istoveten z: prEN 747-1
ICS:
97.140 Pohištvo Furniture
oSIST prEN 747-1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 747-1:2010
---------------------- Page: 2 ----------------------
oSIST prEN 747-1:2010
EUROPEAN STANDARD
DRAFT
prEN 747-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2010
ICS 97.140 Will supersede EN 13453-1:2004, EN 747-1:2007
English Version
Furniture - Bunk beds and high beds - Part 1: Safety, strength
and durability requirements
Meubles - Lits superposés et lits surélevés - Partie 1: Möbel - Etagenbetten und Hochbetten - Teil 1:
Exigences de sécurité, de résistance et de durabilité Anforderungen an die Sicherheit, Festigkeit und
Dauerhaltbarkeit
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 207.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 747-1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 747-1:2010
prEN 747-1 :2010 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Safety requirements .6
4.1 Materials .6
4.2 Construction .6
4.2.1 General .6
4.2.2 Accessible holes gaps and openings .7
4.2.3 Safety barriers .7
4.2.4 Bed base .8
4.2.5 Ladder or other means of access .8
4.3 Strength of ladder or other means of access .9
4.3.1 Attachment, deflection and strength .9
4.4 Strength of frame and fastenings . 10
4.5 Stability . 10
4.6 Fastening of the upper bed to the lower bed . 10
5 Instructions for use . 10
6 Marking . 11
2
---------------------- Page: 4 ----------------------
oSIST prEN 747-1:2010
prEN 747-1 :2010 (E)
Foreword
This document (prEN 747-1:2010) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the
secretariat of which is held by UNI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 747-1:2007, EN 13453-1:2004.
3
---------------------- Page: 5 ----------------------
oSIST prEN 747-1:2010
prEN 747-1 :2010 (E)
Introduction
This part of EN 747 specifies requirements for bunk beds and high beds for use by one occupant per bed.
4
---------------------- Page: 6 ----------------------
oSIST prEN 747-1:2010
prEN 747-1 :2010 (E)
1 Scope
This European Standard specifies requirements for the safety, strength and durability of bunk beds and high
beds. The loads and forces in the strength and durability tests apply to beds with an internal length greater
than 140 cm and a maximum bed base width of 120 cm.
The dimensional requirements are particularly intended to minimise the risk of accidents happening to
children.
The strength and durability requirements are intended to represent use of a bed by one occupant only.
Safety requirements for other products included in a bunk bed/high bed, e.g. a table or storage furniture, are
not included in this standard.
This European Standard does not apply to bunk beds and high beds for special purposes, including but not
limited to prison, military and fire brigades.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
prEN 747-2, Furniture – Bunk beds and high beds – Part 2: Test methods
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
bunk bed
set of components that can be assembled as beds, one above the other, the upper surface of the top bed
base of which is 800 mm or more above floor level
3.2
high bed
set of components that can be assembled as a bed, the upper surface of the bed base of which is 800 mm or
more above floor level, irrespective of the use to which the space below is put
3.3
bed end structures
upright unit at the head and foot of the bed to which the side rails are attached
3.4
bed base
support structure for a mattress
3.5
safety barrier
component intended to prevent an occupant from falling out of the upper bed or the high bed
5
---------------------- Page: 7 ----------------------
oSIST prEN 747-1:2010
prEN 747-1 :2010 (E)
3.6
side rail
longitudinal member attached to the bed end structure by which the bed base can be supported
3.7
tread
structure intended as a foothold, including ladder rungs and steps, but not parts of the bed structure
4 Safety requirements
4.1 Materials
Wood and wood-based material shall be visually free of infestation.
4.2 Construction
4.2.1 General
Accessible edges and corners shall be rounded or chamfered and free from burrs or sharp edges.
Ther
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.