SIST EN ISO 10113:2014
(Main)Metallic materials - Sheet and strip - Determination of plastic strain ratio (ISO 10113:2006)
Metallic materials - Sheet and strip - Determination of plastic strain ratio (ISO 10113:2006)
EN ISO 10113 specifies a method for determining the plastic strain ratio of flat products (sheet and strip) made of metallic materials.
Metallische Werkstoffe - Blech und Band - Bestimmung der senkrechten Anisotropie (ISO 10113:2006)
Diese Internationale Norm legt ein Verfahren zur Bestimmung der senkrechten Anisotropie von Flach-produkten (Blech und Band) aus metallischen Werkstoffen fest.
Matériaux métalliques - Tôles et bandes - Détermination du coefficient d'anisotropie plastique (ISO 10113:2006)
L'ISO 10113:2006 spécifie une méthode de détermination du coefficient d'anisotropie plastique des produits plats (tôles et bandes) en matériaux métalliques.
Kovinski materiali - Pločevina in trakovi - Ugotavljanje količnika plastične anizotropije (ISO 10113:2006)
Standard EN ISO 10113 določa metodo za ugotavljanje količnika plastične anizotropije ploščatih izdelkov (pločevine in trakov), izdelanih iz kovinskih materialov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10113:2014
01-september-2014
.RYLQVNLPDWHULDOL3ORþHYLQDLQWUDNRYL8JRWDYOMDQMHNROLþQLNDSODVWLþQH
DQL]RWURSLMH ,62
Metallic materials - Sheet and strip - Determination of plastic strain ratio (ISO
10113:2006)
Metallische Werkstoffe - Blech und Band - Bestimmung der senkrechten Anisotropie
(ISO 10113:2006)
Matériaux métalliques - Tôles et bandes - Détermination du coefficient d'anisotropie
plastique (ISO 10113:2006)
Ta slovenski standard je istoveten z: EN ISO 10113:2014
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
SIST EN ISO 10113:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10113:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 10113:2014
EUROPEAN STANDARD
EN ISO 10113
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 77.040.10
English Version
Metallic materials - Sheet and strip - Determination of plastic
strain ratio (ISO 10113:2006)
Matériaux métalliques - Tôles et bandes - Détermination du Metallische Werkstoffe - Blech und Band - Bestimmung der
coefficient d'anisotropie plastique (ISO 10113:2006) senkrechten Anisotropie (ISO 10113:2006)
This European Standard was approved by CEN on 6 June 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10113:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10113:2014
EN ISO 10113:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10113:2014
EN ISO 10113:2014 (E)
Foreword
The text of ISO 10113:2006 has been prepared by Technical Committee ISO/TC 164 “Mechanical testing of
metals” of the International Organization for Standardization (ISO) and has been taken over as EN
ISO 10113:2014 by Technical Committee ECISS/TC 101 “Test methods for steel (other than chemical
analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn
at the latest by December 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10113:2006 has been approved by CEN as EN ISO 10113:2014 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10113:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 10113:2014
INTERNATIONAL ISO
STANDARD 10113
Second edition
2006-09-01
Corrected version
2007-08-01
Metallic materials — Sheet and strip —
Determination of plastic strain ratio
Matériaux métalliques — Tôles et bandes — Détermination du
coefficient d'anisotropie plastique
Reference number
ISO 10113:2006(E)
©
ISO 2006
---------------------- Page: 7 ----------------------
SIST EN ISO 10113:2014
ISO 10113:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10113:2014
ISO 10113:2006(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Symbols. 3
5 Principle. 4
6 Test equipment. 4
7 Test piece. 4
8 Procedure. 4
9 Expression of results. 6
10 Test report. 8
Annex A (informative) International comparison of symbols used in the determination of plastic
strain ratio . 9
Bibliography . 10
© ISO 2006 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10113:2014
ISO 10113:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10113 was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals, Subcommittee
SC 2, Ductility testing.
This second edition cancels and replaces the first edition (ISO 10113:1991), which has been technically
revised.
This corrected version of ISO 10113:2006 incorporates the following corrections.
⎯ In 3.1, the definition has been updated and previous Note 4 has been incorporated into Note 2.
1)
⎯ In 3.2 and 3.3, second indexes for the strain level have been added. The previous footnote has been
inserted as Note 2.
⎯ In Table 1, corrections to the symbols and designations have been made for specified plastic strain,
specified plastic strain range, plastic strain ratio, weighted average of r values and the slope of the
x/y
elastic part of the stress/percentage extension curve.
⎯ In 9.2, the word “a” has been deleted in the second line between “For” and “better”.
⎯ Symbol corrections have been made in Equation (5) and Equation (7).
⎯ Figures 1 and 2 and the associated keys have been modified.
iv © ISO 2006 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10113:2014
INTERNATIONAL STANDARD ISO 10113:2006(E)
Metallic materials — Sheet and strip — Determination of plastic
strain ratio
1 Scope
This International Standard specifies a method for determining the plastic strain ratio of flat products (sheet
and strip) made of metallic materials.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 6892:1998, Metallic materials — Tensile testing at ambient temperature
ISO 9513:1999, Metallic materials — Calibration of extensometers used in uniaxial testing
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
plastic strain ratio
r
ratio of the true plastic width strain to the true plastic thickness strain in a test piece that has been subjected to
uniaxial tensile stress
ε
b
r = (1)
ε
a
where
ε is the true plastic thickness strain;
a
ε is the true plastic width strain.
b
NOTE 1 The above expression using a single point is only valid in the region where the plastic strain is homogeneous.
NOTE 2 Since it is easier and more precise to measure changes in length than in thickness, the following relationship
derived from the law of constancy of volume is used up to the percentage plastic extension at maximum force, A , to
g
calculate the plastic strain ratio, r.
For some materials exhibiting a phase change during plastic deformation, the volume of the measured section cannot
always be assumed to be constant. In such cases, the procedure should be defined and agreed between the parties
involved.
© ISO 2006 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 10113:2014
ISO 10113:2006(E)
⎛⎞
b
ln
⎜⎟
⎜⎟
b
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Metallische Werkstoffe - Blech und Band - Bestimmung der senkrechten Anisotropie (ISO 10113:2006)Matériaux métalliques - Tôles et bandes - Détermination du coefficient d'anisotropie plastique (ISO 10113:2006)Metallic materials - Sheet and strip - Determination of plastic strain ratio (ISO 10113:2006)77.140.50SROL]GHONLFlat steel products and semi-products77.040.10Mehansko preskušanje kovinMechanical testing of metalsICS:Ta slovenski standard je istoveten z:FprEN ISO 10113kSIST FprEN ISO 10113:2014en,fr,de01-februar-2014kSIST FprEN ISO 10113:2014SLOVENSKI
STANDARD
kSIST FprEN ISO 10113:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 10113
December 2013 ICS 77.040.10 English Version
Metallic materials - Sheet and strip - Determination of plastic strain ratio (ISO 10113:2006)
Matériaux métalliques - Tôles et bandes - Détermination du coefficient d'anisotropie plastique (ISO 10113:2006)
Metallische Werkstoffe - Blech und Band - Bestimmung der senkrechten Anisotropie (ISO 10113:2006) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee ECISS/TC 101.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 10113:2013: EkSIST FprEN ISO 10113:2014
FprEN ISO 10113:2013 (E) 2 Contents Page Foreword .3
kSIST FprEN ISO 10113:2014
FprEN ISO 10113:2013 (E) 3 Foreword The text of ISO 10113:2006 has been prepared by Technical Committee ISO/TC 164 “Mechanical testing of metals” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 10113:2013. This document is currently submitted to the Unique Acceptance Procedure. Endorsement notice The text of ISO 10113:2006 has been approved by CEN as FprEN ISO 10113:2013 without any modification. kSIST FprEN ISO 10113:2014
kSIST FprEN ISO 10113:2014
Reference numberISO 10113:2006(E)© ISO 2006
INTERNATIONAL STANDARD ISO10113Second edition2006-09-01Corrected version2007-08-01 Metallic materials — Sheet and strip — Determination of plastic strain ratio Matériaux métalliques — Tôles et bandes — Détermination du coefficient d'anisotropie plastique
kSIST FprEN ISO 10113:2014
ISO 10113:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2006 – All rights reserved
kSIST FprEN ISO 10113:2014
ISO 10113:2006(E) © ISO 2006 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 4 Symbols.3 5 Principle.4 6 Test equipment.4 7 Test piece.4 8 Procedure.4 9 Expression of results.6 10 Test report.8 Annex A (informative)
International comparison of symbols used in the determination of plastic strain ratio.9 Bibliography.10
kSIST FprEN ISO 10113:2014
ISO 10113:2006(E) iv © ISO 2006 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10113 was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals, Subcommittee SC 2, Ductility testing. This second edition cancels and replaces the first edition (ISO 10113:1991), which has been technically revised. This corrected version of ISO 10113:2006 incorporates the following corrections. ⎯ In 3.1, the definition has been updated and previous Note 4 has been incorporated into Note 2. ⎯ In 3.2 and 3.3, second indexes for the strain level have been added. The previous footnote 1) has been inserted as Note 2. ⎯ In Table 1, corrections to the symbols and designations have been made for specified plastic strain, specified plastic strain range, plastic strain ratio, weighted average of rx/y values and the slope of the elastic part of the stress/percentage extension curve. ⎯ In 9.2, the word “a” has been deleted in the second line between “For” and “better”. ⎯ Symbol corrections have been made in Equation (5) and Equation (7). ⎯ Figures 1 and 2 and the associated keys have been modified.
kSIST FprEN ISO 10113:2014
INTERNATIONAL STANDARD ISO 10113:2006(E) © ISO 2006 – All rights reserved 1Metallic materials — Sheet and strip — Determination of plastic strain ratio 1 Scope This International Standard specifies a method for determining the plastic strain ratio of flat products (sheet and strip) made of metallic materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6892:1998, Metallic materials — Tensile testing at ambient temperature ISO 9513:1999, Metallic materials — Calibration of extensometers used in uniaxial testing 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 plastic strain ratio r ratio of the true plastic width strain to the true plastic thickness strain in a test piece that has been subjected to uniaxial tensile stress barεε= (1) where aε=is=the=t±×e=plastic=thickness=st±ain;=bε=is=the=t±×e=plastic=width=st±ain.=NOTβ=1=The=above=e•p±ession=×sing=a=single=point=is=only=valid=in=the=±egion=whe±e=the=plastic=st±ain=is=homogeneo×s.=NOTβ=2==Since=it=is=easie±=and=mo±e=p±ecise=to=meas×±e=changes=in=length=than=in=thickness,=the=following=±elationship=de±ived=f±om=the=law=of=constancy=of=vol×me=is=×sed=×p=to=the=pe±centage=plastic=e•tension=at=ma•im×m=fo±ce,=Ag, to calculate the plastic strain ratio, r. For some materials exhibiting a phase change during plastic deformation, the volume of the measured section cannot always be assumed to be constant. In such cases, the procedure should be defined and agreed between the parties involved. kSIST FprEN ISO 10113:2014
ISO 10113:2006(E) 2 © ISO 2006 – All rights reserved ooolnlnbbrLbLb⎛⎞⎜⎟⎜⎟⎝⎠=⎛⎞⎜⎟⎝⎠ (2) NOTE 3 Because the value r depends on the orientation of the test piece relative to the rolling direction, as well as on the strain level, the symbol r may be supplemented by the angle which characterises this orientation and the strain level. For example r45/20 (see Table 1). 3.2 weighted average plastic strain ratio r weighted average of the rx/y values for different tes
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.