SIST EN 62841-2-11:2016
(Main)Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 2-11: Particular requirements for hand-held reciprocating saws (jig and sabre saws) (IEC 62841-2-11:2015)
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 2-11: Particular requirements for hand-held reciprocating saws (jig and sabre saws) (IEC 62841-2-11:2015)
This standard applies to reciprocating saws such as jig saws and sabre saws.
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 2-11: Besondere Anforderungen für handgeführte hin- und hergehende Sägen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 2-11: Exigences particulières pour les scies alternatives portatives
L'IEC 62841-2-11:2015 s'applique aux scies alternatives telles que les scies sauteuses et les scies sabres. La tension assignée est inférieure à 250 V pour les outils à courant monophasé alternatif ou continu, et inférieure à 480 V pour les outils à courant alternatif triphasé. La puissance assignée est inférieure à 3 700 W. Les limites d'application de la présente Norme aux outils fonctionnant sur batterie sont indiquées dans l'Annexe K. La présente Norme traite des dangers présentés par les outils, encourus par tous les individus dans l'utilisation normale et dans l'utilisation impropre raisonnablement prévisible de ces outils. Les outils électroportatifs, qui peuvent être montés sur un support de travail pour être utilisés comme outils installés à poste fixe sans aucune modification de l'outil lui-même, sont compris dans le domaine portatif et d'un support est considérée comme un outil portable, donc couvert par la Partie 3 applicable. La présente Partie 2-11 doit être utilisée conjointement avec la première édition de l'IEC 62841-1. L'attention des Comités Nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication.
Mots clés: scie alternative, scie sauteuse, scie sabre, outils protatifs, outil portable
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-11. del: Posebne zahteve za ročne povratne žage (vbodne in sabljaste žage) (IEC 62841-2-11:2015)
Ta standard se uporablja za povratne žage, kot so vbodne in sabljaste žage.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62841-2-11:2016
01-julij-2016
1DGRPHãþD
SIST EN 60745-2-11:2010
(OHNWURPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO 3RVHEQH]DKWHYH]DURþQHSRYUDWQHåDJH YERGQHLQVDEOMDVWHåDJH ,(&
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 2-11: Particular requirements for hand-held reciprocating saws
(jig and sabre saws) (IEC 62841-2-11:2015)
Ta slovenski standard je istoveten z: EN 62841-2-11:2016
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 62841-2-11:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62841-2-11:2016
---------------------- Page: 2 ----------------------
SIST EN 62841-2-11:2016
EUROPEAN STANDARD EN 62841-2-11
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2016
ICS 25.140.20; 25.140.30 Supersedes EN 60745-2-11:2010
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-11: Particular
requirements for hand-held reciprocating saws
(IEC 62841-2-11:2015, modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-11: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies alternatives portatives Gartenmaschinen - Sicherheit - Teil 2-11: Besondere
(IEC 62841-2-11:2015, modifiée) Anforderungen für handgeführte hin- und hergehende
Sägen
(IEC 62841-2-11:2015, modifiziert)
This European Standard was approved by CENELEC on 2015-12-23. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-2-11:2016 E
---------------------- Page: 3 ----------------------
SIST EN 62841-2-11:2016
EN 62841-2-11:2016 (E)
European foreword
The text of document 116/246/FDIS, future edition 1 of IEC 62841-2-11, prepared by IEC/TC 116 "Safety
of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-2-11:2016.
A draft amendment, which covers common modifications to IEC 62841-2-11, was prepared by
CLC/TC 116 "Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
– latest date by which this document has to be implemented (dop) 2016-12-23
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2019-12-23
with this document have to be withdrawn
EN 62841-2-11:2016 supersedes EN 60745-2-11:2010.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could come within the
scope of this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 2-11 is to be used in conjunction with EN 62841-1:2015.
This Part 2-11 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert
it into the European Standard: Particular requirements for hand-held reciprocating saws (jig and sabre
saws).
Where a particular subclause of Part 1 is not mentioned in this Part 2-11, that subclause applies as far as
relevant. Where this standard states "addition", "modification" or "replacement", the relevant text in Part 1
is to be adapted accordingly.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting
from 101.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-2-11:2015 are prefixed “Z”.
2
---------------------- Page: 4 ----------------------
SIST EN 62841-2-11:2016
EN 62841-2-11:2016 (E)
This European Standard follows the overall requirements of EN ISO 12100.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
Compliance with the clauses of Part 1 together with this Part 2-11 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
3
---------------------- Page: 5 ----------------------
SIST EN 62841-2-11:2016
EN 62841-2-11:2016 (E)
Endorsement notice
The text of the International Standard IEC 62841-2-11:2015 was approved by CENELEC as a European
Standard with agreed common modifications.
COMMON MODIFICATIONS
Replace the title of Annex I by the following:
Annex I
(normative)
Measurement of noise and vibration emissions
Annex K
(normative)
Battery tools and battery packs
Add the following new subclause:
K.21.18.Z101 Isolation device
Reciprocating saws with an integral battery shall be equipped with an isolation device to prevent the
risk of injury from mechanical hazards during user maintenance that:
– ensures a reliable disconnection of at least one pole of the battery from the relevant load(s);
– has a reliable mechanical link between the manual control and the disconnecting element(s);
– is equipped with an unambiguous indication of the state of the disconnection device which
corresponds to each position of its manual control (actuator);
– protects against accidental reconnection.
NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, removable batteries or an
electromechanical power switch with a direct mechanical link between the actuator and the contact.
NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.1.2. The other
examples in NOTE 1 achieve this by the necessary actions for reconnection.
Compliance is checked by inspection.
4
---------------------- Page: 6 ----------------------
SIST EN 62841-2-11:2016
EN 62841-2-11:2016 (E)
Annex L
(normative)
Battery tools and battery packs provided with
mains connection or non-isolated sources
Add the following new subclause:
L.21.18.Z101 Isolation device
Reciprocating saws with an integral battery shall be equipped with an isolation device to prevent the
risk of injury from mechanical hazards during user maintenance that:
– ensures a reliable disconnection of at least one pole of the battery from the relevant load(s);
– has a reliable mechanical link between the manual control and the disconnecting element(s);
– is equipped with an unambiguous indication of the state of the disconnection device which
corresponds to each position of its manual control (actuator);
– protects against accidental reconnection.
NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, removable batteries or an
electromechanical power switch with a direct mechanical link between the actuator and the contact.
NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.1.2. The other
examples in NOTE 1 achieve this by the necessary actions for reconnection.
Compliance is checked by inspection.
5
---------------------- Page: 7 ----------------------
SIST EN 62841-2-11:2016
EN 62841-2-11:2016 (E)
Add the following annexes:
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
This annex from Part 1 is applicable with the following addition:
Publication Year Title EN/HD Year
ISO 16893-1 2008 Wood-based panels - Particleboard - - -
Part 1: Classifications
6
---------------------- Page: 8 ----------------------
SIST EN 62841-2-11:2016
EN 62841-2-11:2016 (E)
Annex ZZ
(informative)
Relationship between this European standard and the essential requirements of
Directive 2006/42/EC [2006 OJ L157] aimed to be covered
This European standard has been prepared under a Commission’s standardisation request M/396 to
provide one voluntary means of conforming to essential requirements of Directive 2006/42/EC of the
European Parliament and of the Council of 17 May 2006 on machinery, and amending
Directive 95/16/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding essential requirements of that
Directive, and associated EFTA regulations.
Table ZZ.1 – Correspondence between this European Standard
and Annex I of Directive 2006/42/EC
Essential Requirements of Clause(s) / sub-clause(s)
Remarks / Notes
Directive 2006/42/EC of this EN
Annex I All clauses All corresponding requirements
are covered by complying with all
clauses.
WARNING 1: Presumption of conformity stays valid only as long as a reference to this European standard is
maintained in the list published in the Official Journal of the European Union. Users of this standard should consult
frequently the latest list published in the Official Journal of the European Union.
WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of this standard.
7
---------------------- Page: 9 ----------------------
SIST EN 62841-2-11:2016
---------------------- Page: 10 ----------------------
SIST EN 62841-2-11:2016
IEC 62841-2-11
®
Edition 1.0 2015-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 2-11: Particular requirements for hand-held reciprocating saws
Outils électroportatifs à moteur, outils portables et machines pour jardins et
pelouses – Sécurité –
Partie 2-11: Exigences particulières pour les scies alternatives portatives
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.140.20, 25.140.30 ISBN 978-2-8322-2998-9
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 11 ----------------------
SIST EN 62841-2-11:2016
– 2 – IEC 62841-2-11:2015 © IEC 2015
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General requirements . 6
5 General conditions for the tests . 7
6 Radiation, toxicity and similar hazards . 7
7 Classification . 7
8 Marking and instructions . 7
9 Protection against access to live parts . 7
10 Starting . 7
11 Input and current . 8
12 Heating . 8
13 Resistance to heat and fire . 8
14 Moisture resistance . 8
15 Resistance to rusting . 8
16 Overload protection of transformers and associated circuits . 8
17 Endurance . 8
18 Abnormal operation . 8
19 Mechanical hazards . 8
20 Mechanical strength . 9
21 Construction . 9
22 Internal wiring . 9
23 Components . 10
24 Supply connection and external flexible cords . 10
25 Terminals for external conductors . 10
26 Provision for earthing . 10
27 Screws and connections . 10
28 Creepage distances, clearances and distances through insulation . 10
Annexes . 13
Annex I (informative) Measurement of noise and vibration emissions . 13
Annex K (normative) Battery tools and battery packs . 20
Annex L (normative) Battery tools and battery packs provided with mains connection
or non-isolated sources . 21
Bibliography . 22
Figure 101 – Test probe . 11
Figure 102 – Typical designs of jig saws . 12
Figure 103 – Typical designs of sabre saws . 12
Figure I.101 – Test set-up for jig saws . 17
Figure I.102 – Test set-up for sabre saws . 18
---------------------- Page: 12 ----------------------
SIST EN 62841-2-11:2016
IEC 62841-2-11:2015 © IEC 2015 – 3 –
Figure I.103 – Positions of transducers for sabre saws . 19
Figure I.104 – Positions of transducers for jig saws . 19
Table 4 – Required performance levels . 8
Table I.101 – Test conditions for sabre and jig saws cutting board . 14
Table I.102 – Test conditions for jig saws cutting sheet metal . 15
Table I.103 – Test conditions for sabre saws cutting wooden beams . 15
---------------------- Page: 13 ----------------------
SIST EN 62841-2-11:2016
– 4 – IEC 62841-2-11:2015 © IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS,
TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 2-11: Particular requirements for hand-held reciprocating saws
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62841-2-11 has been prepared by IEC technical committee 116:
Safety of motor-operated electric tools.
The text of this standard is based on the following documents:
FDIS Report on voting
116/246/FDIS 116/256/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 14 ----------------------
SIST EN 62841-2-11:2016
IEC 62841-2-11:2015 © IEC 2015 – 5 –
This Part 2-11 is to be used in conjunction with the first edition of IEC 62841-1 (2014).
This Part 2-11 supplements or modifies the corresponding clauses in IEC 62841-1, so as to
convert it into the IEC standard: Particular requirements for hand-held reciprocating saws.
Where a particular subclause of Part 1 is not mentioned in this Part 2-11, that subclause
applies as far as relevant. Where this standard states “addition”, “modification” or
“replacement”, the relevant text in Part 1 is to be adapted accordingly.
The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes and figures which are additional to those in Part 1 are numbered starting
from 101.
A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated
hand-held tools, transportable tools and lawn and garden machinery – Safety, can be found
on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 36 months from the date of publication.
---------------------- Page: 15 ----------------------
SIST EN 62841-2-11:2016
– 6 – IEC 62841-2-11:2015 © IEC 2015
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS,
TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 2-11: Particular requirements for hand-held reciprocating saws
1 Scope
This clause of Part 1 is applicable, except as follows:
Addition:
This part of IEC 62841 applies to reciprocating saws such as jig saws and sabre saws.
2 Normative references
This clause of Part 1 is applicable, except as follows:
Addition:
ISO 16893-1:2008, Wood based panels – Particleboard – Part 1: Classifications
3 Terms and definitions
This clause of Part 1 is applicable, except as follows:
Additional definitions:
3.101
reciprocating saw
tool intended for cutting various materials with a blade or blades acting in a reciprocating or
oscillating motion
3.102
jig saw
reciprocating saw with a base plate that may allow bevel adjustments
Note 1 to entry: Typical designs of jig saws are shown in Figure 102.
3.103
sabre saw
reciprocating saw with a guide plate that may allow tilting movements
Note 1 to entry: Typical designs of sabre saws are shown in Figure 103.
4 General requirements
This clause of Part 1 is applicable.
---------------------- Page: 16 ----------------------
SIST EN 62841-2-11:2016
IEC 62841-2-11:2015 © IEC 2015 – 7 –
5 General conditions for the tests
This clause of Part 1 is applicable, except as follows:
5.17 Addition:
The mass of the tool includes the dust extraction adapter, if any.
6 Radiation, toxicity and similar hazards
This clause of Part 1 is applicable.
7 Classification
This clause of Part 1 is applicable.
8 Marking and instructions
This clause of Part 1 is applicable, except as follows:
8.14.1 Addition:
For reciprocating saws, the additional safety instructions as specified in 8.14.1.101 shall be
given. This part may be printed separately from the “General Power Tool Safety Warnings”.
8.14.1.101 Safety instructions for reciprocating saws
Hold the power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to a stable
platform. Holding the workpiece by hand or against your body leaves it unstable and may
lead to loss of control.
NOTE The above warning is not applicable for garden saws for tree or hedge services.
8.14.2 b) Addition:
101) Instruction on the correct use of the dust collection system, if any;
102) Information regarding the cutting capacity;
103) Instruction on how to adjust the tool for different saw blade positions, if applicable.
8.14.2 c) Addition:
101) Instruction on how to properly clean/clear the chip ejection opening, if any.
9 Protection against access to live parts
This clause of Part 1 is applicable.
10 Starting
This clause of Part 1 is applicable.
---------------------- Page: 17 ----------------------
SIST EN 62841-2-11:2016
– 8 – IEC 62841-2-11:2015 © IEC 2015
11 Input and current
This clause of Part 1 is applicable.
12 Heating
This clause of Part 1 is applicable.
13 Resistance to heat and fire
This clause of Part 1 is applicable.
14 Moisture resistance
This clause of Part 1 is applicable.
15 Resistance to rusting
This clause of Part 1 is applicable.
16 Overload protection of transformers and associated circuits
This clause of Part 1 is applicable.
17 Endurance
This clause of Part 1 is applicable.
18 Abnormal operation
This clause of Part 1 is applicable, except as follows:
18.8 Replacement of Table 4:
Table 4 – Required performance levels
Type and purpose of SCF Minimum performance
level (PL)
Power switch – prevent unwanted switch-on
b
Power switch – provide desired switch-off for jig saws a
Power switch – provide desired switch-off for sabre saws b
Any electronic control to pass the test of 18.3 Not an SCF
Any speed limiting device Not an SCF
Prevent exceeding thermal limits as in Clause 18 a
Prevent self-resetting as required in 23.3 b
19 Mechanical hazards
This clause of Part 1 is applicable, except as follows:
---------------------- Page: 18 ----------------------
SIST EN 62841-2-11:2016
IEC 62841-2-11:2015 © IEC 2015 – 9 –
19.1 Replacement of the first paragraph:
Moving and dangerous parts other than the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.