SIST EN ISO 18388:2019
(Main)Technical product documentation (TPD) - Relief grooves - Types and dimensioning (ISO 18388:2016)
Technical product documentation (TPD) - Relief grooves - Types and dimensioning (ISO 18388:2016)
This International Standard specifies a series of relief grooves for shafts and holes, intended for general use in mechanical engineering.
It also intends to avoid unnecessary multiplicity of tools by a restricted selection of groove-types and dimensional versions.
NOTE The shape and the dimensions of the relief grooves type G and H correspond with the “Indexable hard material inserts” according to ISO 6987.
Technische Produktdokumentation (TPD) - Freistiche - Formen und Maße (ISO 18388:2016)
Diese Internationale Norm legt eine Reihe von Freistichen für Drehteile und Bohrungen zur allgemeinen Anwendung im Maschinenbau fest.
Dadurch soll eine unnötige Vielzahl von Werkzeugen durch eine eingeschränkte Auswahl an Freisticharten und Maßvarianten vermieden werden.
ANMERKUNG Die Freistiche der Formen G und H stimmen hinsichtlich ihrer Form und ihrer Maße mit „Wende-schneidplatten aus Hartmetall“ nach ISO 6987 überein.
Documentation technique de produits (DPT) - Rainures en relief - Types et dimensionnement (ISO 18388:2016)
La présente Norme internationale spécifie une série de rainures en relief pour arbres et trous, destinées à un usage général en construction mécanique.
Elle vise également à éviter une multiplicité inutile d'outils en limitant le choix des types de rainures et des versions dimensionnelles.
NOTE La forme et les dimensions des rainures en relief de type G et H correspondent à celles des "Plaquettes amovibles en matériaux durs" selon l'ISO 6987.
Tehnična dokumentacija izdelkov - Sprostilni utori - Vrste in dimenzioniranje (ISO 18388:2016)
Ta mednarodni standard določa nabor sprostilnih utorov za jaške in odprtine, namenjenih za splošno uporabo v strojništvu.
Namen tega standarda je tudi preprečiti nepotrebno množico orodij z omejeno izbiro sprostilnih utorov in dimenzijskih različic.
OPOMBA: Oblika in dimenzije sprostilnih utorov vrste G in H ustrezajo »indeksirnim vložkom iz trdega materiala« v skladu s standardom ISO 6987.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 18388:2019
01-december-2019
Tehnična dokumentacija izdelkov - Sprostilni utori - Vrste in dimenzioniranje (ISO
18388:2016)
Technical product documentation (TPD) - Relief grooves - Types and dimensioning (ISO
18388:2016)
Technische Produktdokumentation (TPD) - Freistiche - Formen und Maße (ISO
18388:2016)
Documentation technique de produits (DPT) - Rainures en relief - Types et
dimensionnement (ISO 18388:2016)
Ta slovenski standard je istoveten z: EN ISO 18388:2019
ICS:
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
SIST EN ISO 18388:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 18388:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 18388:2019
EN ISO 18388
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 01.100.20
English Version
Technical product documentation (TPD) - Relief grooves -
Types and dimensioning (ISO 18388:2016)
Documentation technique de produits (DPT) - Rainures Technische Produktdokumentation (TPD) - Freistiche -
en relief - Types et dimensionnement (ISO Formen und Maße (ISO 18388:2016)
18388:2016)
This European Standard was approved by CEN on 5 August 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18388:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 18388:2019
EN ISO 18388:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 18388:2019
EN ISO 18388:2019 (E)
European foreword
The text of ISO 18388:2016 has been prepared by Technical Committee ISO/TC 10 "Technical product
documentation” of the International Organization for Standardization (ISO) and has been taken over as
EN ISO 18388:2019 by CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 18388:2016 has been approved by CEN as EN ISO 18388:2019 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 18388:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 18388:2019
INTERNATIONAL ISO
STANDARD 18388
First edition
2016-02-15
Technical product documentation
(TPD) — Relief grooves — Types and
dimensioning
Documentation technique de produits (DPT) — Rainures en relief —
Types et dimensionnement
Reference number
ISO 18388:2016(E)
©
ISO 2016
---------------------- Page: 7 ----------------------
SIST EN ISO 18388:2019
ISO 18388:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 18388:2019
ISO 18388:2016(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
4.1 Relief groove type E . 1
4.2 Relief groove type F . 2
4.3 Relief groove type G . 2
4.4 Relief groove type H . 3
5 Dimensions of the relief grooves . 4
5.1 Relief grooves . 4
5.2 Countersink at the counterpart . 5
6 Designation . 5
7 Presentation on the drawing . 6
7.1 General . 6
7.2 Conventional representation . 6
7.3 Simplified representation . 7
Bibliography . 8
© ISO 2016 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 18388:2019
ISO 18388:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
co
...
SLOVENSKI STANDARD
oSIST prEN ISO 18388:2019
01-maj-2019
7HKQLþQDGRNXPHQWDFLMDL]GHONRY5HOLHIQLXWRUL9UVWHLQGLPHQ]LRQLUDQMH ,62
Technical product documentation (TPD) - Relief grooves - Types and dimensioning (ISO
18388:2016)
Documentation technique de produits (DPT) - Rainures en relief - Types et
dimensionnement (ISO 18388:2016)
Ta slovenski standard je istoveten z: prEN ISO 18388
ICS:
01.110 7HKQLþQDGRNXPHQWDFLMD]D Technical product
L]GHONH documentation
oSIST prEN ISO 18388:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 18388:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 18388:2019
INTERNATIONAL ISO
STANDARD 18388
First edition
2016-02-15
Technical product documentation
(TPD) — Relief grooves — Types and
dimensioning
Documentation technique de produits (DPT) — Rainures en relief —
Types et dimensionnement
Reference number
ISO 18388:2016(E)
©
ISO 2016
---------------------- Page: 3 ----------------------
oSIST prEN ISO 18388:2019
ISO 18388:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 18388:2019
ISO 18388:2016(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
4.1 Relief groove type E . 1
4.2 Relief groove type F . 2
4.3 Relief groove type G . 2
4.4 Relief groove type H . 3
5 Dimensions of the relief grooves . 4
5.1 Relief grooves . 4
5.2 Countersink at the counterpart . 5
6 Designation . 5
7 Presentation on the drawing . 6
7.1 General . 6
7.2 Conventional representation . 6
7.3 Simplified representation . 7
Bibliography . 8
© ISO 2016 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 18388:2019
ISO 18388:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electro technical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 10, Technical product documentation,
Subcommittee SC 6, Mechanical engineering documentation.
iv © ISO 2016 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 18388:2019
INTERNATIONAL STANDARD ISO 18388:2016(E)
Technical product documentation (TPD) — Relief grooves
— Types and dimensioning
1 Scope
This International Standard specifies a ser
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.