SIST EN 747-2:2012+A1:2015
(Main)Furniture - Bunk beds and high beds - Part 2: Test methods
Furniture - Bunk beds and high beds - Part 2: Test methods
This European Standard specifies test methods for the safety, strength and durability of bunk beds and high beds for domestic and non-domestic use. The loads and forces in the strength and durability tests apply to beds with an internal length greater than 140 cm and a maximum bed base width of 120 cm.
The tests are designed to be applied to a bed that is fully assembled and ready for use.
The applicable safety requirements are given in EN 747-1.
Möbel - Etagenbetten und Hochbetten - Teil 2: Prüfverfahren
Diese Europäische Norm legt Prüfverfahren zur Sicherheit, Festigkeit und Dauerhaltbarkeit von Etagenbetten und Hochbetten für den Wohn- und Objektbereich fest. Die für die Festigkeits- und Dauerhaltbarkeits-prüfungen festgelegten Belastungen und Kräfte gelten für Betten mit einer inneren Länge von mehr als 140 cm und einer Höchstbreite des Bettbodens von 120 cm. Die Prüfungen sind an einem vollständig zusammengebauten und gebrauchsfertigen Bett durchzuführen. Die entsprechenden Sicherheitsanforderungen sind in EN 747-1 angegeben.
Meubles - Lits superposés et lits surélevés - Partie 2: Méthodes d'essai
La présente Norme européenne spécifie des méthodes d’essai pour évaluer la sécurité, la résistance et la durabilité des lits superposés et des lits surélevés à usage domestique et collectif. Les charges et forces spécifiées pour les essais de résistance et de durabilité s’appliquent aux lits de longueur interne supérieure à 140 cm et dont le sommier à une largeur maximale de 120 cm.
Les essais sont conçus pour être appliqués à un lit entièrement assemblé et prêt à l’emploi.
Les exigences de sécurité associées sont stipulées dans la EN 747-1.
Pohištvo - Pogradi in visoke postelje - 2. del: Preskusne metode
Ta evropski standard določa preskusne metode za varnost, trdnost ter trajnost pogradov in visokih postelj za domačo in javno rabo. Obremenitve in sile v preskusih trdnosti in trajnosti veljajo za postelje, katerih notranja dolžina presega 140 cm in pri katerih širina dna meri 120 cm.
Preskusi so zasnovani za postelje, ki so povsem sestavljene in pripravljene za uporabo.
Ustrezne varnostne zahteve so navedene v standardu EN 747-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 747-2:2012+A1:2015
01-september-2015
Pohištvo - Pogradi in visoke postelje - 2. del: Preskusne metode
Furniture - Bunk beds and high beds - Part 2: Test methods
Möbel - Etagenbetten und Hochbetten - Teil 2: Prüfverfahren
Meubles - Lits superposés et lits surélevés - Partie 2: Méthodes d'essai
Ta slovenski standard je istoveten z: EN 747-2:2012+A1:2015
ICS:
97.140 Pohištvo Furniture
SIST EN 747-2:2012+A1:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 747-2:2012+A1:2015
---------------------- Page: 2 ----------------------
SIST EN 747-2:2012+A1:2015
EUROPEAN STANDARD
EN 747-2:2012+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2015
ICS 97.140 Supersedes EN 747-2:2012
English Version
Furniture - Bunk beds and high beds - Part 2: Test methods
Meubles - Lits superposés et lits surélevés - Partie 2: Möbel - Etagenbetten und Hochbetten - Teil 2:
Méthodes d'essai Prüfverfahren
This European Standard was approved by CEN on 8 March 2012 and includes Amendment 1 approved by CEN on 16 April 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 747-2:2012+A1:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 747-2:2012+A1:2015
EN 747-2:2012+A1:2015 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Normative references .5
3 General test conditions .5
3.1 Preliminary preparation .5
3.2 Application of forces .6
3.3 Tolerances .6
4 Test equipment .6
4.1 General .6
4.2 Measuring cones.6
4.3 Bed base impactor .7
4.3.1 Bed base impactor (see Figure 2) .7
4.3.2 Springs .7
4.3.3 Striking surface .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.