SIST EN 3763:2010

Aerospace series - Nuts, hexagonal, self-locking, ball seat, in heat resisting steel, MoS2 lubricated - Classification: 900 MPa (at ambient temperature)/315 °C

This standard specifies the characteristics of self-locking hexagonal nuts with ball seat in heat resisting steel, MoS2 lubricated. Classification: 900 MPa / 315 °C. They are intended to be used with washers to EN 3764 or suitable parts, see Annex A.

Luft- und Raumfahrt - Sechskantmuttern, selbstsichernd, für Neigungsausgleich, aus hochwarmfestem Stahl, MoS2-geschmiert - Klasse: 900 MPa (bei Raumtemperatur)/315 °C

Diese Norm legt die Merkmale von selbstsichernden Sechskantmuttern zum Neigungsausgleich aus hochwarmfestem Stahl, MoS2-geschmiert, fest.
Klasse: 900 MPa  )/ 315 °C  )
Sie sind für die Verwendung zusammen mit Scheiben nach EN 3764 oder geeigneten Teilen ausgelegt, siehe Anhang A.

Série aérospatiale - Écrous hexagonaux, à freinage interne, orientables, en acier résistant à chaud, lubrifiés MoS2 - Classification: 900 MPa (à température ambiante)/315 °C

Aeronavtika - Matice, šestrobe, samozapiralne, z izravnavo nagiba, iz toplotnoodpornega jekla, mazane z MoS2 - Klasifikacija: 900 MPa (pri temperaturi okolice)/315 °C

Ta standard določa značilnosti samozapiralnih šestrobih matic z izravnavo nagiba iz toplotnoodpornega jekla in mazanih z MoS2. Klasifikacija: 900 MPa /315 °C. Namenjene so za uporabo z tesnili EN 3764 ali ustreznimi deli, glej Dodatek A.

General Information

• Status: Published
• Publication Date: 01-Feb-2010
• ICS: 49.030.30 - Nuts
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Feb-2010
• Due Date: 08-Apr-2010
• Completion Date: 02-Feb-2010
• Ref Project: EN 3763:2010 - Aerospace series - Nuts, hexagonal, self-locking, ball seat, in heat resisting steel, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 315 °C

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 3763:2010
01-marec-2010
Aeronavtika - Matice, šestrobe, samozapiralne, z izravnavo nagiba, iz
toplotnoodpornega jekla, mazane z MoS2 - Klasifikacija: 900 MPa (pri temperaturi
okolice)/315 °C
Aerospace series - Nuts, hexagonal, self-locking, ball seat, in heat resisting steel, MoS2
lubricated - Classification: 900 MPa (at ambient temperature)/315 °C
Luft- und Raumfahrt - Sechskantmuttern, selbstsichernd, für Neigungsausgleich, aus
hochwarmfestem Stahl, MoS2-geschmiert - Klasse: 900 MPa (bei Raumtemperatur)/315
°C
Série aérospatiale - Écrous hexagonaux, à freinage interne, orientables, en acier
résistant à chaud, lubrifiés MoS2 - Classification: 900 MPa (à température ambiante)/315
°C
Ta slovenski standard je istoveten z: EN 3763:2010
ICS:
49.030.30 Matice Nuts
SIST EN 3763:2010 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 3763:2010

---------------------- Page: 2 ----------------------

SIST EN 3763:2010


EUROPEAN STANDARD
EN 3763

NORME EUROPÉENNE

EUROPÄISCHE NORM
January 2010
ICS 49.030.30
English Version
Aerospace series - Nuts, hexagonal, self-locking, ball seat, in
heat resisting steel, MoS lubricated - Classification: 900 MPa
2
(at ambient temperature) / 315 °C
Série aérospatiale - Écrous hexagonaux, à freinage interne, Luft- und Raumfahrt - Sechskantmuttern, selbstsichernd,
orientables, en acier résistant à chaud, lubrifiés MoS2 - für Neigungsausgleich, aus hochwarmfestem Stahl, MoS2-
Classification: 900 MPa (à température ambiante) / 315 °C geschmiert - Klasse: 900 MPa (bei Raumtemperatur) / 315
°C
This European Standard was approved by CEN on 4 December 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3763:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 3763:2010
EN 3763:2010 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Required characteristics .5
4 Designation .7
5 Marking .7
6 Technical specification .7
Annex A (informative) Assembly .8

2

---------------------- Page: 4 ----------------------

SIST EN 3763:2010
EN 3763:2010 (E)
Foreword
This document (EN 3763:2010) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by July 2010, and conflicting national standards shall be withdrawn at the
latest by July 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations,
...