oSIST prEN ISO 17660-1:2017

Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints (ISO/DIS 17660-1:2017)

2018-06-28: WI abandoned to follow cancellation of WI in ISO (notification from ISO to dataservice on 2018-06-18).

Schweißen - Schweißen von Betonstahl - Teil 1: Tragende Schweißverbindungen (ISO/DIS 17660-1:2017)

Dieser Teil von ISO 17660 gilt für das Schweißen von schweißgeeigneten Betonstählen und nichtrostenden Betonstählen für tragende Schweißverbindungen in Betrieben und auf der Baustelle. Er legt Anforderungen für Werkstoffe, Gestaltung und Ausführung von Schweißverbindungen, Schweißpersonal, Qualitätsanforde-rungen, Untersuchung und Prüfung fest.
Dieser Teil von ISO 17660 enthält auch Verbindungen zwischen Betonstahlstäben und anderen Stahlteilen, wie Verbindungseinheiten, Verankerungen, einschließlich vorgefertigter Einbauteile. Nichttragende Schweiß-verbindungen werden durch ISO 17660-2 erfasst.
Dieser Teil von ISO 17660 gilt nicht für die fabrikmäßige Herstellung von Betonstahlmatten und Gitter-trägern auf Mehrfachpunktschweißmaschinen oder auf Mehrfachbuckelschweißmaschinen.
Die Anforderungen dieses Teils von ISO 17660 gelten nur für ruhend beanspruchte Bauteile.
ANMERKUNG Für dynamisch beanspruchte Bauteile wird empfohlen, in Abhängigkeit der Stoßart und des Schweiß-prozesses, eine merkliche Verminderung der dynamischen Festigkeit des Betonstahls zu berücksichtigen.

Soudage - Soudage des aciers pour armature - Partie 1: Assemblages transmettant les efforts (ISO/DIS 17660-1:2017)

Varjenje - Varjenje betonskega jekla - 1. del: Obremenjeni zvarni spoji (ISO/DIS 17660-1:2017)

General Information

• Status: Not Published
• Public Enquiry End Date: 31-Oct-2017
• ICS: 25.160.10 - Welding processes
• Technical Committee: VAR - Welding
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 22-Aug-2018
• Due Date: 27-Aug-2018
• Completion Date: 22-Aug-2018
• Ref Project: prEN ISO 17660-1 - Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints (ISO/DIS 17660-1:2017)

Relations

• Revised: SIST EN ISO 17660-1:2007 - Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints (ISO 17660-1:2006)
• Effective Date: 01-Oct-2017
• Revised: SIST EN ISO 17660-1:2007 - Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints (ISO 17660-1:2006)
• Effective Date: 18-Jan-2023
• Revised: SIST EN ISO 17660-1:2007 - Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints (ISO 17660-1:2006)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 17660-1:2017
01-oktober-2017
Varjenje - Varjenje betonskega jekla - 1. del: Obremenjeni zvarni spoji (ISO/DIS
17660-1:2017)
Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints (ISO/DIS
17660-1:2017)
Schweißen - Schweißen von Betonstahl - Teil 1: Tragende Schweißverbindungen
(ISO/DIS 17660-1:2017)
Soudage - Soudage des aciers pour armature - Partie 1: Assemblages transmettant les
efforts (ISO/DIS 17660-1:2017)
Ta slovenski standard je istoveten z: prEN ISO 17660-1
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
oSIST prEN ISO 17660-1:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 17660-1:2017

---------------------- Page: 2 ----------------------
oSIST prEN ISO 17660-1:2017
DRAFT INTERNATIONAL STANDARD
ISO/DIS 17660-1
ISO/TC 44/SC 10 Secretariat: DIN
Voting begins on: Voting terminates on:
2017-08-28 2017-11-19
Welding — Welding of reinforcing steel —
Part 1:
Load-bearing welded joints
Soudage — Soudage des aciers d’armatures —
Partie 1: Assemblages transmettant des efforts
ICS: 25.160.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 17660-1:2017(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2017

---------------------- Page: 3 ----------------------
oSIST prEN ISO 17660-1:2017
ISO/DIS 17660-1:2017(E) ISO/DIS 17660-1:2017(E)

Contents Page
Foreword . vi
Introduction . vii
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Symbols and abbreviated terms .3
5 Welding processes .4
6 Load-bearing welded joints .4
6.1 General .4
6.2 Butt joints .5
6.2.1 Butt joints welded by welding processes 111, 114, 135, 136 and 138 .5
6.2.2 Butt joints welded by welding processes 24, 25 and 42 .6
6.2.3 Butt joints welded by welding process 47 .6
6.3 Lap joints .7
6.4 Strap joints .7
6.5 Cross joints .8
6.5.1 General .8
6.5.2 Cross joints for welding processes 111, 114, 135, 136, 138 .8
6.5.3 Cross joints for welding processes 21 and 23 .9
6.6 Joints between reinforcing steel bars and other steel components . 10
6.6.1 General . 10
6.6.2 Types of joint . 10
7 Materials . 15
7.1 Parent materials . 15
7.1.1 Reinforcing steels . 15
7.1.2 Other types of steels . 15
7.1.3 Inspection documents . 15
7.2 Welding consumables . 15
8 Quality requirements . 15
9 Welding personnel . 16
9.1 Welding coordination . 16
9.2 Welder and operator qualifications. 16
9.2.1 Welders . 16
9.2.2 Welding operators and resistance weld setters . 17
COPYRIGHT PROTECTED DOCUMENT
9.3 Validity of a welder qualification test . 17
© ISO 2017, Published in Switzerland
10 Welding procedure specification (WPS) . 17
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
11 Welding procedures . 17
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester. 11.1 General . 17
11.2 Test specimens . 17
ISO copyright office
Ch. de Blandonnet 8 • CP 401
11.3 Examination and testing . 17
CH-1214 Vernier, Geneva, Switzerland
11.4 Acceptance criteria . 18
Tel. [phone]
11.5 Range of qualification . 18
Fax [phone]
[e-mail]
www.iso.org
© ISO 2017 – All rights reserved
iii
ii © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 17660-1:2017
ISO/DIS 17660-1:2017(E)
Contents Page
Foreword . vi
Introduction . vii
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Symbols and abbreviated terms .3
5 Welding processes .4
6 Load-bearing welded joints .4
6.1 General .4
6.2 Butt joints .5
6.2.1 Butt joints welded by welding processes 111, 114, 135, 136 and 138 .5
6.2.2 Butt joints welded by welding processes 24, 25 and 42 .6
6.2.3 Butt joints welded by welding process 47 .6
6.3 Lap joints .7
6.4 Strap joints .7
6.5 Cross joints .8
6.5.1 General .8
6.5.2 Cross joints for welding processes 111, 114, 135, 136, 138 .8
6.5.3 Cross joints for welding processes 21 and 23 .9
6.6 Joints between reinforcing steel bars and other steel components . 10
6.6.1 General . 10
6.6.2 Types of joint . 10
7 Materials . 15
7.1 Parent materials . 15
7.1.1 Reinforcing steels . 15
7.1.2 Other types of steels . 15
7.1.3 Inspection documents . 15
7.2 Welding consumables . 15
8 Quality requirements . 15
9 Welding personnel . 16
9.1 Welding coordination . 16
9.2 Welder and operator qualifications. 16
9.2.1 Welders . 16
9.2.2 Welding operators and resistance weld setters . 17
9.3 Validity of a welder qualification test . 17
10 Welding procedure specification (WPS) . 17
11 Welding procedures . 17
11.1 General . 17
11.2 Test specimens . 17
11.3 Examination and testing . 17
11.4 Acceptance criteria . 18
11.5 Range of qualification . 18
© ISO 2017 – All rights reserved
iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 17660-1:2017
ISO/DIS 17660-1:2017(E)
11.5.1 Material . 18
11.5.2 Load-bearing/Non load-bearing . 18
11.5.3 Production route of reinforcing steel . 18
11.5.4 Diameter of reinforcing steel bar and material thickness . 18
11.5.5 Transverse end plate joints . 19
11.5.6 Other essential variables . 19
11.6 Validity . 20
12 Production weld test . 20
13 Execution and inspection of production welding of reinforcing steel . 21
13.1 General . 21
13.2 Welding of bent reinforcing steel bars . 22
13.3 Welds made by welding processes 21 and 23 . 23
13.4 Welds made by welding processes 24 and 25 . 23
13.5 Welds made by welding process 42 . 23
13.6 Welds made by welding process 47 . 23
14 Examination and testing of test specimens . 24
14.1 General . 24
14.2 Tensile test . 24
14.2.1 Test specimen . 24
14.2.2 Test procedure . 24
14.2.3 Evaluation of results . 24
14.2.4 Report of results . 25
14.3 Shear test . 25
14.3.1 Test specimen . 25
14.3.2 Test procedure . 25
14.3.3 Evaluation of results . 25
14.3.4 Report of results . 26
14.4 Bend test . 26
14.4.1 Test specimen . 26
14.4.2 Test procedure . 27
14.4.3 Evaluation of results . 27
14.4.4 Reporting of results . 27
15 Production log . 27
Annex A (informative) Welding procedure specification (WPS) . 28
A.1 Welding processes 111, 114, 135, 136 and 138 . 28
A.2 Welding process 47 . 30
Annex B (informative) Technical knowledge of welding coordinator for welding reinforcing
steel . 31
Annex C (informative) Test specimens . 32
C.1 General . 32
C.2 Test specimens . 32
Annex D (informative) Assessment of the manufacturer performing welding . 36
Annex E (informative) Evaluation of testing of welded joints . 37
Annex F (informative) Example for production log . 38
Annex G (informative) Classification of shear strenght of load-bearing cross joints . 39
Annex H (informative) Examples of diameter combiantions for welding cross joints using
welding processes 21 and 23 . 40
© ISO 2017 – All rights reserved
iv

---------------------- Page: 6 ----------------------
oSIST prEN ISO 17660-1:2017
ISO/DIS 17660-1:2017(E) ISO/DIS 17660-1:2017(E)
11.5.1 Material . 18
Bibliography . 41
11.5.2 Load-bearing/Non load-bearing . 18

11.5.3 Production route of reinforcing steel . 18

11.5.4 Diameter of reinforcing steel bar and material thickness . 18
11.5.5 Transverse end plate joints . 19
11.5.6 Other essential variables . 19
11.6 Validity . 20
12 Production weld test . 20
13 Execution and inspection of production welding of reinforcing steel . 21
13.1 General . 21
13.2 Welding of bent reinforcing steel bars . 22
13.3 Welds made by welding processes 21 and 23 . 23
13.4 Welds made by welding processes 24 and 25 . 23
13.5 Welds made by welding process 42 . 23
13.6 Welds made by welding process 47 . 23
14 Examination and testing of test specimens . 24
14.1 General . 24
14.2 Tensile test . 24
14.2.1 Test specimen . 24
14.2.2 Test procedure . 24
14.2.3 Evaluation of results . 24
14.2.4 Report of results . 25
14.3 Shear test . 25
14.3.1 Test specimen . 25
14.3.2 Test procedure . 25
14.3.3 Evaluation of results . 25
14.3.4 Report of results . 26
14.4 Bend test . 26
14.4.1 Test specimen . 26
14.4.2 Test procedure . 27
14.4.3 Evaluation of results . 27
14.4.4 Reporting of results . 27
15 Production log . 27
Annex A (informative) Welding procedure specification (WPS) . 28
A.1 Welding processes 111, 114, 135, 136 and 138 . 28
A.2 Welding process 47 . 30
Annex B (informative) Technical knowledge of welding coordinator for welding reinforcing
steel .
...