Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control (IEC 60684-3-282:2010)

This part of IEC 60684 gives the requirements for two types of heat-shrinkable, polyolefin sleeving, stress control, not flame retarded, with a nominal shrink ratio up to 3:1. This sleeving has been found suitable for use up to temperatures of 100 °C.
– Type A : Medium wall                        Internal diameter up to 65,0 mm typically
– Type B : Thick wall                             Internal diameter up to 95,0 mm typically
These sleevings are normally supplied in colour black. Since these types of sleevings cover a significantly large range of sizes and wall thicknesses, Tables A.1 and A.2 in this standard provides guidance to the range of sizes available. The actual size shall be agreed between the user and the supplier. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This sleeving is designed to be used in MV cable accessories and as such electrical performance must be proven as part of the assembly. Examples of this are described in
HD 629 and the IEC 60502 series.

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 282: Polyolefin- Wärmeschrumpfschläuche mit Feldsteuerung (IEC 60684-3-282:2010)

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 282: Gaines thermorétractables en polyoléfine - Contrôle de fatigue (CEI 60684-3-282:2010)

La CEI 60684-3-282:2010 donne les exigences relatives à deux types de gaines thermorétractables, en polyoléfine, à contrôle de fatigue, non ignifugées, de rapport de rétreint nominal jusqu'à 3:1. Ces gaines se sont révélées être adaptées à une utilisation à des températures jusqu'à 100 °C.   - Type A: Paroi moyenne - Diamètre intérieur type jusqu'à 65,0 mm  - Type B: Paroi épaisse - Diamètre intérieur type jusqu'à 95,0 mm

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 282. list: Toplotno skrčljive poliolefinske cevi, preskušanje z obremenjevanjem (IEC 60684-3-282:2010)

Ta del IEC 60684 podaja zahteve za dva tipa toplotno skrčljivih poliolefinskih cevi za preskušanje z obremenjevanjem, ki niso ognjevarne in ki imajo nazivno razmerje krčenja do 3:1. Za te cevi je ugotovljeno, da so primerne za uporabo pri temperaturah do 100 °C.
- Tip A: Srednje debela stena. Notranji premer običajno do 65,0 mm.
- Tip B: Debela stena. Notranji premer običajno do 95,0 mm.
Te cevi se običajno dobavljajo v črni barvi. Ker te vrste cevi zajemajo precej velik razpon velikosti in debelin stene, podajata preglednici A.1. in A.2 v tem standardu vodilo o razponu razpoložljivih velikosti. Dejanska velikost se dogovori med uporabnikom in dobaviteljem. Materiali, skladni s to specifikacijo, ustrezajo vzpostavljenim ravnem delovanja. Vendar mora uporabnik material za določeno uporabo izbrati na podlagi dejanskih zahtev za ustrezno delovanje pri takšni uporabi, in ne le na podlagi same specifikacije. Ta cevi so zasnovane za uporabo v kabelskih dodatkih srednje napetosti, zato mora biti dokazana njihova električna zmogljivost, kadar so del sklopa. Primeri tega so opisani v HD 629 in seriji IEC 60502.

General Information

Status
Published
Publication Date
19-Oct-2010
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-Oct-2010
Due Date
10-Dec-2010
Completion Date
20-Oct-2010

Buy Standard

Standard
EN 60684-3-282:2010
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2010
*LENHL]RODFLMVNHFHYLGHO6SHFLILNDFLMH]DSRVDPH]QHWLSHFHYLOLVW
7RSORWQRVNUþOMLYHSROLROHILQVNHFHYLSUHVNXãDQMH]REUHPHQMHYDQMHP ,(&

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet
282: Heat-shrinkable, polyolefin sleeving - Stress control (IEC 60684-3-282:2010)
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 282:
Polyolefin- Wärmeschrumpfschläuche mit Feldsteuerung (IEC 60684-3-282:2010)
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuille 282: Gaines thermorétractables en polyoléfine - Contrôle de fatigue (CEI 60684-3
-282:2010)
Ta slovenski standard je istoveten z: EN 60684-3-282:2010
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60684-3-282
NORME EUROPÉENNE
September 2010
EUROPÄISCHE NORM
ICS 29.035.20
English version
Flexible insulating sleeving -
Part 3: Specifications for individual types of sleeving -
Sheet 282: Heat-shrinkable, polyolefin sleeving -
Stress control
(IEC 60684-3-282:2010)
Gaines isolantes souples -  Isolierschläuche -
Partie 3: Spécifications pour types Teil 3: Anforderungen für einzelne
particuliers de gaines - Schlauchtypen -
Feuille 282: Gaines thermorétractables Blatt 282: Polyolefin-
en polyoléfine - Wärmeschrumpfschläuche
Contrôle de fatigue mit Feldsteuerung
(CEI 60684-3-282:2010) (IEC 60684-3-282:2010)

This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-282:2010 E

Foreword
The text of document 15/564/FDIS, future edition 1 of IEC 60684-3-282, prepared by IEC TC 15, Solid
electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by
CENELEC as EN 60684-3-282 on 2010-09-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2011-06-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2013-09-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60684-3-282:2010 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60684-3-282:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

- - Test requirements on accessories for use on HD 629.1 S2 2006
power cables of rated voltage
from 3,6/6(7,2) kV up to 20,8/36(42) kV -
Part 1: Cables with extruded insulation

IEC 60296 2003 Fluids for electrotechnical applications - EN 60296 2004
Unused mineral insulating oils for + corr. September 2004
transformers and switchgear
IEC 60502 Series Power cables with extruded insulation and - -
their accessories for rated voltages from 1 kV
(Um = 1,2 kV) up to 30 kV (Um = 36 kV)

IEC 60684-1 2003 Flexible insulating sleeving - EN 60684-1 2003
Part 1: Definitions and general requirements

IEC 60684-2 1997 Flexible insulating sleeving - EN 60684-2 1997
+ A1 2003 Part 2: Methods of test + A1 2003
+ A2 2005 + A2 2005
IEC 60757 1983 Code for designation of colours HD 457 S1 1985

IEC 60684-3-282 ®
Edition 1.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Flexible insulating sleeving –
Part 3: Specifications for individual types of sleeving –
Sheet 282: Heat-shrinkable, polyolefin sleeving – Stress control

Gaines isolantes souples –
Partie 3: Spécifications pour types particuliers de gaines –
Feuille 282: Gaines thermorétractables en polyoléfine – Contrôle de fatigue

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
J
CODE PRIX
ICS 29.035.20 ISBN 978-2-88910-962-3
– 2 – 60684-3-282 © IEC:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Designation .7
4 Conditions of test .7
5 Requirements .7
6 Sleeving conformance .7
Annex A (informative) Guidance on the available sizes and wall thicknesses .9

Table 1 – Property requirements .7
Table 2 – Resistance to selected fluids .8
Table A.1 – Type A, medium wall.9
Table A.2 – Type B, thick wall.9

60684-3-282 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheet 282: Heat-shrinkable, polyolefin sleeving –
Stress control
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by I
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.