SIST EN IEC 60684-3-282:2025

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control (IEC 60684-3-282:2025)

This part of IEC 60684 gives the requirements for two types of heat-shrinkable, polyolefin sleeving, stress control, not flame retarded, with a nominal shrink ratio up to 3:1.
This sleeving has been found suitable for use up to temperatures of 100 °C.
- Type A : Medium wall Internal diameter up to 65,0 mm typically
- Type B : Thick wall Internal diameter up to 95,0 mm typically
This sleeving is normally supplied in the colour black.
Since these types of sleevings cover a significantly large range of sizes and wall thicknesses, Annex A in this standard provides guidance to the range of sizes available. The actual size will be agreed between the user and the supplier.
Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application need to be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
This sleeving is designed to be used in MV cable accessories and as such electrical performance will be proven as part of the assembly. Examples of this are described in HD 629 and IEC 60502 (all parts)

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 282: Polyolefin-Wärmeschrumpfschläuche mit Feldsteuerung (IEC 60684-3-282:2025)

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 282: Gaines thermorétractables en polyoléfine - Contrôle de fatigue (IEC 60684-3-282:2025)

L'IEC 60684-3-282:2025 donne les exigences relatives à deux types de gaines thermorétractables, en polyoléfine, à contrôle de contrainte, non ignifugées, avec un rapport de rétreint nominal jusqu'à 3:1.
Ces gaines se sont révélées être adaptées à une utilisation à des températures allant jusqu’à 100 °C.
Type A: Paroi moyenne Diamètre intérieur type jusqu’à 65,0 mm
Type B: Paroi épaisse Diamètre intérieur type jusqu’à 95,0 mm
Comme ces types de gaines couvrent une gamme très étendue de dimensions et d’épaisseurs de paroi, l'Annexe A fournit des recommandations quant à la gamme des dimensions disponibles. Les dimensions réelles font l’objet d’un accord entre l’utilisateur et le fournisseur.

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 282. list: Toplotno skrčljive poliolefinske cevi, preskušanje z obremenjevanjem (IEC 60684-3-282:2025)

Ta del standarda IEC 60684 podaja zahteve za dva tipa neognjevarnih toplotno skrčljivih poliolefinskih cevi, preskušenih z obremenjevanjem, z nazivnim razmerjem krčenja do 3:1.
Te cevi so primerne za uporabo pri temperaturah do 100 °C.
– Tip A: srednje debela stena – notranji premer običajno do 65,0 mm.
– Tip B: debela stena – notranji premer običajno do 95,0 mm.
Ker ti tipi cevi zajemajo precej velik razpon velikosti in debelin sten, so v dodatku A podana navodila glede razpona razpoložljivih velikosti. O dejanski velikosti se dogovorita uporabnik in dobavitelj.

General Information

• Status: Published
• Publication Date: 25-Jun-2025
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: IIZS - Insulating materials and systems
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 18-Jun-2025
• Due Date: 23-Aug-2025
• Completion Date: 26-Jun-2025
• Ref Project: EN IEC 60684-3-282:2025 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control

Relations

• Revised: SIST EN 60684-3-282:2010 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control (IEC 60684-3-282:2010)
• Effective Date: 01-Sep-2025

Overview

EN IEC 60684-3-282:2025 specifies requirements for heat-shrinkable, polyolefin insulating sleeving - stress control. It is part of the IEC 60684 series on flexible insulating sleeving and covers two types (medium and thick wall) with a nominal shrink ratio up to 3:1. The sleeving is not flame retarded, is normally supplied black, and is judged suitable for use up to 100 °C. The sheet is intended primarily for use in MV cable accessories, where final electrical performance is verified as part of the complete assembly.

Key topics & technical requirements

• Types covered
  • Type A (medium wall): internal diameters typically up to 65.0 mm
  • Type B (thick wall): internal diameters typically up to 95.0 mm
• Material & performance scope
  • Heat-shrinkable polyolefin designed for stress control applications
  • Materials meeting this specification provide established performance levels, but final material selection must be based on the application
• Test and conditioning
  • Pre-test shrinking: forced-air oven, (10 ± 1) min at 200 °C ± 3 K
  • Specified tests include tensile strength, elongation at break, heat shock (e.g., 150 °C), low-temperature bending (test at −40 °C), dimensional stability and fluid resistance
  • Conformance typically evaluated on recovered internal diameters 25–30 mm
• Designation & labelling
  • Example format: Sleeving IEC 60684-3-282-A-45,0/20,0-BK (sheet/type/expanded & recovered ID/colour)
• Guidance on sizes
  • Annex A provides guidance on the available ranges of sizes and wall thicknesses; the exact size is agreed between supplier and purchaser

Applications

• Medium- and high-voltage (MV) cable accessories requiring stress control at transition points
• Cable joints, terminations and assemblies where controlled stress relief and mechanical protection are required
• Industrial and utility installations where heat-shrink sleeving is specified for insulation and stress grading

Who should use this standard

• Cable accessory manufacturers and material suppliers
• Design and test engineers for MV cable systems
• Procurement and compliance teams specifying insulating components for electrical assemblies
• Certification and test laboratories assessing sleeving mechanical and thermal performance

Related standards

• IEC 60684-1 (definitions & general requirements)
• IEC 60684-2:2025 (methods of test)
• IEC 60757 (colour designation)
• IEC 60296 (insulating oils) and application references such as HD 629 and IEC 60502 (MV cable accessories)

Keywords: EN IEC 60684-3-282:2025, heat-shrinkable polyolefin sleeving, stress control sleeving, flexible insulating sleeving, MV cable accessories, IEC 60684, medium wall, thick wall, heat-shrink sleeving specifications.

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2025
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 282. list:
Toplotno skrčljive poliolefinske cevi, preskušanje z obremenjevanjem (IEC 60684-3
-282:2025)
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet
282: Heat-shrinkable, polyolefin sleeving - Stress control (IEC 60684-3-282:2025)
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 282:
Polyolefin-Wärmeschrumpfschläuche mit Feldsteuerung (IEC 60684-3-282:2025)
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuille 282: Gaines thermorétractables en polyoléfine - Contrôle de fatigue (IEC 60684-3
-282:2025)
Ta slovenski standard je istoveten z: EN IEC 60684-3-282:2025
ICS:
29.035.20 Plastični in gumeni izolacijski Plastics and rubber insulating
materiali materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60684-3-282

NORME EUROPÉENNE
EUROPÄISCHE NORM June 2025
ICS 29.035.20 Supersedes EN 60684-3-282:2010
English Version
Flexible insulating sleeving - Part 3: Specifications for individual
types of sleeving - Sheet 282: Heat-shrinkable, polyolefin
sleeving - Stress control
(IEC 60684-3-282:2025)
Gaines isolantes souples - Partie 3: Spécifications pour Isolierschläuche - Teil 3: Anforderungen für einzelne
types particuliers de gaines - Feuille 282: Gaines Schlauchtypen - Blatt 282: Polyolefin-
thermorétractables en polyoléfine - Contrôle de contrainte Wärmeschrumpfschläuche mit Feldsteuerung
(IEC 60684-3-282:2025) (IEC 60684-3-282:2025)
This European Standard was approved by CENELEC on 2025-06-06. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60684-3-282:2025 E

European foreword
The text of document 15/1045/FDIS, future edition 2 of IEC 60684-3-282, prepared by TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60684-3-282:2025.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2026-06-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-06-30
document have to be withdrawn
This document supersedes EN 60684-3-282:2010 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60684-3-282:2025 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60684-3 (all sheets) NOTE Approved as EN 60684-3 (all sheets)

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60296 - Fluids for electrotechnical applications - Mineral EN IEC 60296 -
insulating oils for electrical equipment
IEC 60684-1 - Flexible insulating sleeving - Part 1: Definitions EN 60684-1 -
and general requirements
IEC 60684-2 2025 Flexible insulating sleeving - Part 2: Methods of EN IEC 60684-2 -
test
IEC 60757 - Code for designation of colours EN IEC 60757 -

IEC 60684-3-282 ®
Edition 2.0 2025-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Flexible insulating sleeving –
Part 3: Specifications for individual types of sleeving – Sheet 282: Heat-
shrinkable, polyolefin sleeving – Stress control

Gaines isolantes souples –
Partie 3: Spécifications pour types particuliers de gaines – Feuille 282: Gaines
thermorétractables en polyoléfine – Contrôle de contrainte
ICS 29.035.20  ISBN 978-2-8327-0380-9

IEC 60684-3-282:2025-05(en-fr)

– 2 – IEC 60684-3-282:2025 © IEC 2025
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Designation . 7
5 Conditions of test . 7
6 Requirements . 7
7 Sleeving conformance . 7
Annex A (informative) Guidance on the available sizes and wall thicknesses . 10
Bibliography . 11

Table 1 – Property requirements . 8
Table 2 – Resistance to selected fluids . 9
Table A.1 – Type A, medium wall . 10
Table A.2 – Type B, thick wall . 10

IEC 60684-3-282:2025 © IEC 2025 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheet 282: Heat-shrinkable, polyolefin sleeving – Stress control

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National C
...