SIST EN 16002:2010
(Main)Flexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing
Flexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing
This document specifies a test method to determine the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing.
The assessment is limited to the performance of the mechanically fastened flexible sheets only. The test method does not include the determination of the performance of the mechanical fastener and/or the combination of the mechanical fastener and the substrate.
Abdichtungsbahnen - Bestimmung des Widerstandes gegen Windlast von mechanisch befestigten Dachabdichtungsbahnen
Dieses Dokument legt ein Prüfverfahren zur Bestimmung der Windlastbeständigkeit mechanisch befestigter Dachabdichtungsbahnen fest.
Die Bewertung wird ausschließlich auf die Leistung der mechanisch befestigten Abdichtungsbahnen begrenzt. Das Prüfverfahren schließt weder die Bestimmung der Leistung der mechanischen Befestigung noch die Kombination aus der mechanischen Befestigung und des Trägermaterials ein.
Feuilles souples d'étanchéité - Feuilles bitumineuses, en plastique et en caoutchouc destinées à assurer l'étanchéité des toitures - Détermination de la résistance à l'arrachement au vent
Le présent document donne une méthode d’essai pour déterminer la résistance au vent des feuilles souples fixées mécaniquement pour l'étanchéité des toitures.
L'évaluation se limite à la performance des feuilles souples à fixation mécanique. La méthode d’essai n'inclut pas la détermination de la performance de la fixation mécanique ni celle de la combinaison de la fixation et du support.
Hidroizolacijski trakovi - Določanje odpornosti mehansko pritrjenih hidroizolacijskih trakov za tesnjenje streh proti obremenitvi z vetrom
Ta evropski standard določa preskusno metodo za določanje odpornosti mehansko pritrjenih hidroizolacijskih trakov za tesnjenje proti obremenitvi z vetrom. Ocena je omejena samo na delovanje mehansko pritrjenih trakov. Preskusna metoda ne vsebuje določanja delovanje mehanskih sponk in/ali kombinacije mehanske sponke in substrata.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LKHWURPAbdichtungsbahnen - Bestimmung des Widerstandes gegen Windlast von mechanisch befestigten DachabdichtungsbahnenFeuilles souples d'étanchéité - Feuilles bitumineuses, en plastique et en caoutchouc destinées à assurer l'étanchéité des toitures - Détermination de la résistance à l'arrachement au ventFlexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing91.100.50Veziva. Tesnilni materialiBinders. Sealing materials91.060.20StreheRoofsICS:Ta slovenski standard je istoveten z:EN 16002:2010SIST EN 16002:2010en,fr,de01-oktober-2010SIST EN 16002:2010SLOVENSKI
STANDARD
SIST EN 16002:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16002
May 2010 ICS 91.100.50 English Version
Flexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing
Feuilles souples d'étanchéité - Feuilles bitumineuses, en plastique et en caoutchouc destinées à assurer l'étanchéité des toitures - Détermination de la résistance à l'arrachement au vent
Abdichtungsbahnen - Bestimmung des Widerstandes gegen Windlast von mechanisch befestigten Dachabdichtungsbahnen This European Standard was approved by CEN on 23 April 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16002:2010: ESIST EN 16002:2010
EN 16002:2010 (E) 2 Contents Page Foreword .3Introduction .41 Scope .52 Normative references .53 Terms and definitions .54 Symbols and abbreviations .65 Sampling .76 Test conditions .77 Apparatus and additional devices .77.1 Pressure (vacuum) chamber .77.2 Fan including control and recording system .77.2.1 Fan and controlling equipment .77.2.2 Pressure measurement device .77.2.3 Thermometer .87.2.4 Chronometer .87.2.5 Time and pressure measurement and registration device .87.3 Calibration .88 Test specimen .88.1 General .88.2 Dimensions of the test area .88.3 Flexible sheets . 108.4 Insulation . 108.5 Vapour control layers . 108.6 Structural deck . 109 Testing . 109.1 Test procedure . 109.2 Load/time diagram of the gust . 109.3 Installation of the pressure chamber . 139.4 Application of the pressure . 139.5 Registration of test results . 1410 Evaluation and expression of results . 1410.1 Calculation characteristic load . 1410.2 Factor Ca . 1510.3 Factor Cd . 1511 Application rules . 1611.1 General . 1611.2 Substrate . 1611.3 Vapour control layer . 1612 Test report . 16 SIST EN 16002:2010
EN 16002:2010 (E) 3 Foreword This document (EN 16002:2010) has been prepared by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn at the latest by November 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 16002:2010
EN 16002:2010 (E) 4 Introduction The test is performed on a standard test configuration, i.e. a load-bearing structure, a layer of insulation material and the mechanically fastened membrane(s). For the determination of the performance of the mechanical fastening system (fastener and washer), with or without possible substrates, ETAG 006:2000, Annex D may be used. The suppliers of these mechanical fastening systems should provide the required information. For the calculation of the performance of wind load resistance of the whole roof, see the relevant national and/or international standards. The result of this standard is the resistance to wind load of the flexible sheet expressed as the characteristic load per fastener. Safety factors may be defined by national regulation and/or within European or national application documents. In principle, the test apparatus may also be used to assess (partially) bonded flexible sheets, but some modifications and additional guidance are needed. This is the reason to limit the scope of this standard to mechanically fastened sheets only. SIST EN 16002:2010
EN 16002:2010 (E) 5 1 Scope This European Standard specifies a test method to determine the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing. The assessment is limited to the performance of the mechanically fastened flexible sheets only. The test method does not include the determination of the performance of the mechanical fastener and/or the combination of the mechanical fastener and the substrate.
2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10346:2009, Continuously hot-dip coated steel flat products — Technical delivery conditions EN 13162, Thermal insulation products for buildings — Factory made mineral wool (MW) products — Specification EN 13416, Flexible sheets for waterproofing — Bitumen, plastic and rubber sheets for roof waterproofing — Rules for sampling EN 13707:2004+A2:2009, Flexible sheets for waterproofing — Reinforced bitumen sheets for roof waterproofing — Definitions and characteristics EN 13956:2005, Flexible sheet for waterproofing — Plastic and rubber sheets for roof waterproofing — Definitions and characteristics ETAG 006:2000, Guideline for European Technical Approval systems of systems mechanically fastened flexible roof waterproofing membranes 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13707:2004+A2:2009 and EN 13956:2005 and the following apply. 3.1 fastener object to fasten the flexible sheet to a structural deck NOTE A fastener may be made of a washer, a metal sleeve and a screw or of a plastic washer with an integrated sleeve and a metal shank. 3.2 fastening system assembly of components intended to secure a waterproofing system to the structural deck by means of point fasteners or linear fasteners NOTE Whilst primarily intended to secure the covering against wind uplift forces, the system may contribute to securing intermediate layers such as thermal insulation, vapour control layers, etc. 3.3 jointing technique sealing of at least two layers of flexible sheets for roof waterproofing
SIST EN 16002:2010
EN 16002:2010 (E) 6 NOTE This may be done by e.g. bond (torch, adhesive) or welding (hot air, chemicals). 3.4 linear fastener continuous strip or lath perforated by point fasteners intended to secure the flexible sheets for roof waterproofing in the general area of the roof and/or at its perimeter NOTE The strip or lath is commonly made of metal. 3.5 point fastener shaft, in form of a screw, nail or expanding anchor, together with a disc-shaped washer or collar NOTE Forces may be transmitted to the fastener by the clamping action of the washer or by bond between a plastic surface on the washer and a plastic roof covering, or by other means. 3.6 test specimen representative part of the roof, consisting of one or more layers of flexible sheet for roof waterproofing, an insulation layer and a structural deck 3.7 structural deck roofing panel which has to transfer both permanent and variable loads to the other construction parts of the roof or building 3.8 vapour control layer sheet used to limit the transportation of water vapour into any part of the roof 4 Symbols and abbreviations For the purposes of this document, the following symbols apply. Unit Ai area of influence of the fastener mm2 a maximum spacing between rows of fasteners
mm b maximum spacing between individual fasteners in a row mm Ca geometric correction factor - Cd statistical correctio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.