SIST EN 13445-5:2002/A4:2007

Unfired pressure vessels - Part 5: Inspection and testing

Delete the third paragraph:
This Part does not give inspection and testing provisions for vessels designed using Design by Analysis - Direct Route (DBA) of EN 13445-3:2002 Annex B.
Modification to Clause 1, Clause 2, 5.2.1, 6.6.1, A.1 and Annex ZA.

Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung

Den dritten Absatz streichen:
Dieser Teil der Norm enthält keine Anforderungen an die Inspektion und Prüfung von Behältern, die nach dem Analytischen Zulässigkeitsnachweis (vorher: direkte Auslegung nach Analyseverfahren (DBA)) nach EN 13445 3:2002, Anhang B, hergestellt werden.

Récipients sous pression non soumis a la flamme - Partie 5: Inspection et contrôles

Supprimer le troisieme paragraphe :
La présente partie ne donne pas de dispositions relatives a l'inspection et au contrôle des récipients conçus en utilisant la Conception par Analyse  Méthode directe (DBA), suivant l'EN 13445-3:2002, Annexe B.

Neogrevane tlačne posode – 5. del: Kontrola in preskušanje

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2007
• Withdrawal Date: 19-Jan-2010
• ICS: 23.020.32 - Pressure vessels
• Technical Committee: TLP - Pressure vessels
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 29-Dec-2009
• Due Date: 21-Jan-2010
• Completion Date: 20-Jan-2010
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: EN 13445-5:2002/A4:2006 - Unfired pressure vessels - Part 5: Inspection and testing

Relations

• Replaced By: SIST EN 13445-5:2009 - Unfired pressure vessels - Part 5: Inspection and testing
• Effective Date: 01-Feb-2010
• Amends: SIST EN 13445-5:2002 - Unfired pressure vessels - Part 5: Inspection and testing
• Effective Date: 01-Apr-2007
• Amends: SIST EN 13445-5:2002 - Unfired pressure vessels - Part 5: Inspection and testing
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13445-5:2002/A4:2007
01-april-2007
1HRJUHYDQHWODþQHSRVRGH±GHO.RQWURODLQSUHVNXãDQMH
Unfired pressure vessels - Part 5: Inspection and testing
Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
Récipients sous pression non soumis a la flamme - Partie 5: Inspection et contrôles
Ta slovenski standard je istoveten z: EN 13445-5:2002/A4:2006
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
SIST EN 13445-5:2002/A4:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 13445-5:2002/A4
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2006
ICS 23.020.30

English Version
Unfired pressure vessels - Part 5: Inspection and testing
Récipients sous pression non soumis à la flamme - Partie Unbefeuerte Druckbehälter - Teil 5: Inspektion und Prüfung
5: Inspection et contrôles
This amendment A4 modifies the European Standard EN 13445-5:2002; it was approved by CEN on 21 October 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-5:2002/A4:2006: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 13445-5:2002/A4:2006 (E)
Contents Page
1 Scope.4
5.2 Information to be contained in the technical documentation .4
6.6 Non-destructive testing of welded joints .4
6.6.1 Extent of non-destructive testing.4
Annex A (normative) Inspection and testing of serially produced pressure vessels – Model
acceptance .5
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of the EU Pressure Equipment Directive (97/23/EC) .6

2

---------------------- Page: 3 ----------------------

EN 13445-5:2002/A4:2006 (E)
Foreword
This document (EN 13445-5:2002/A4:2006) has been prepared by Technical Committee CEN/TC 54 “Unfred
pressure vessels”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 13445-5:2002 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national
standards shall be withdrawn at the latest by June 2007.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement t
...