SIST EN ISO 28199-3:2010

Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 3: Visual assessment of sagging, formation of bubbles, pinholing and hiding power (ISO 28199-3:2009)

In many areas (e.g. automotive/industrial/synthetic coatings) the materials used are adapted to the specific application equipment and technologies of the user. Coating materials are, therefore, to be understood as semi-manufactured products that only receive their final form in combination with specific application methods and processes. This is decisive for quality evaluation of the finished product.
The current procedure aims to define standards for evaluation of coatings in research, development and production with regard to their suitability and safety for industrial processes. The procedure is also concerned with fault analysis. As properties of coatings depend on thickness, coating systems of increasing thickness are applied to a test panel under predefined conditions. Film thickness is measured in accordance with ISO 2808. Depending on film thickness the following properties are then determined visually:
- sagging;
- boiling;
- pinholes;
- opacity.

Beschichtungsstoffe - Beurteilung von applikationsbedingter Eigenschaften von Beschichtungssystemen - Teil 3: Visuelle Beurteilung von Ablaufneigung, Kocherbildung, Nadelstichbildung und Deckvermögen (ISO 28199-3:2009)

ISO 28199 legt ein Verfahren zum Beurteilen von Beschichtungsstoffen in Forschung, Entwicklung und Produktion bezüglich ihrer Prozesseignung, Prozesssicherheit und Fehleranalyse fest. Die zu beurteilenden Eigenschaften von Beschichtungsstoffen und Beschichtungen sind abhängig von der Schichtdicke. Hierzu wird unter definierten Bedingungen ein Beschichtungssystem mit ansteigender Schichtdicke auf eine Probenplatte aufgetragen.
Es werden folgende Prüfmerkmale gemessen:
   Schichtdicke nach ISO 2808;
   Oberflächenstruktur;
   Farbe nach ISO 7724;
   Glanz nach ISO 2813 (optional).
Daraus werden in Verbindung mit einer visuellen Beurteilung folgende Eigenschaften bestimmt:
   Farbstabilität, Prozessdeckvermögen, Spritznebelaufnahme, Wolkigkeit, Oberflächenstruktur, Benetzung;
   Ablaufneigung, Kocherbildung, Nadelstichbildung, Deckvermögen.
Dieser Teil von ISO 28199 legt die Bestimmung von Ablaufneigung, Kocherbildung, Nadelstichbildung und Deckvermögen fest.

Peintures et vernis - Évaluation des propriétés des systèmes de revêtement liées au mode d'application - Partie 3: Évaluation visuelle du festonnage, de la formation de bulles, des piqûres et du pouvoir masquant (ISO 28199-3:2009)

L'ISO 28199‑3:2009 spécifie des méthodes visuelles pour l'évaluation de la tendance au festonnage, de la formation de bulles, des piqûres et du pouvoir masquant de produits de peinture appliqués sur un panneau d'essai dans des conditions définies.

Barve in laki - Vrednotenje lastnosti premaznih sistemov pri nanašanju - 3. del: Vizualno ocenjevanje polzenja, pojava mehurčkov, luknjic in kritnosti (ISO 28199-3:2009)

Ta del ISO 28199 opredeljuje vizualne metode ocenjevanja nagnjenosti k polzenju, pojavu mehurčkov, luknjicam in kritnosti premaznih materialov, nanešenih na preskusno ploščo pod določenimi pogoji.

General Information

• Status: Withdrawn
• Publication Date: 19-Nov-2009
• Withdrawal Date: 15-Aug-2021
• ICS: 87.040 - Paints and varnishes
• Technical Committee: IBLP - Paints and varnishes
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 23-Jul-2021
• Due Date: 15-Aug-2021
• Completion Date: 16-Aug-2021
• Ref Project: EN ISO 28199-3:2009 - Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 3: Visual assessment of sagging, formation of bubbles, pinholing and hiding power (ISO 28199-3:2009)

Relations

• Replaced By: SIST EN ISO 28199-3:2021 - Paints and varnishes - Evaluation of properties of coating systems related to the spray application process - Part 3: Assessment of sagging, formation of bubbles, pinholing and hiding power (ISO 28199-3:2021)
• Effective Date: 01-Sep-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 28199-3:2010
01-januar-2010
%DUYHLQODNL9UHGQRWHQMHODVWQRVWLSUHPD]QLKVLVWHPRYSULQDQDãDQMXGHO
9L]XDOQRRFHQMHYDQMHSRO]HQMDSRMDYDPHKXUþNRYOXNQMLFLQNULWQRVWL,62

Paints and varnishes - Evaluation of properties of coating systems related to the
application process - Part 3: Visual assessment of sagging, formation of bubbles,
pinholing and hiding power (ISO 28199-3:2009)
Beschichtungsstoffe - Beurteilung von applikationsbedingter Eigenschaften von
Beschichtungssystemen - Teil 3: Visuelle Beurteilung von Ablaufneigung, Kocherbildung,
Nadelstichbildung und Deckvermögen (ISO 28199-3:2009)
Peintures et vernis - Évaluation des propriétés des systèmes de revêtement liées au
mode d'application - Partie 3: Évaluation visuelle du festonnage, de la formation de
bulles, des piqûres et du pouvoir masquant (ISO 28199-3:2009)
Ta slovenski standard je istoveten z: EN ISO 28199-3:2009
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 28199-3:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 28199-3:2010

---------------------- Page: 2 ----------------------

SIST EN ISO 28199-3:2010


EUROPEAN STANDARD
EN ISO 28199-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2009
ICS 87.040
English Version
Paints and varnishes - Evaluation of properties of coating
systems related to the application process - Part 3: Visual
assessment of sagging, formation of bubbles, pinholing and
hiding power (ISO 28199-3:2009)
Peintures et vernis - Évaluation des propriétés des Beschichtungsstoffe - Beurteilung von
systèmes de revêtement liées au mode d'application -
applikationsbedingter Eigenschaften von
Partie 3: Évaluation visuelle du festonnage, de la formation Beschichtungssystemen - Teil 3: Visuelle Beurteilung von
de bulles, des piqûres et du pouvoir masquant (ISO 28199- Ablaufneigung, Kocherbildung, Nadelstichbildung und
3:2009) Deckvermögen (ISO 28199-3:2009)
This European Standard was approved by CEN on 21 May 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 28199-3:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 28199-3:2010
EN ISO 28199-3:2009 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 28199-3:2010
EN ISO 28199-3:2009 (E)
Foreword
This document (EN ISO 28199-3:2009) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2010, and conflicting national standards shall be withdrawn at
the latest by March 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 28199-3:2009 has been approved by CEN as a EN ISO 28199-3:2009 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 28199-3:2010

---------------------- Page: 6 ----------------------

SIST EN ISO 28199-3:2010

INTERNATIONAL ISO
STANDARD 28199-3
First edition
2009-09-01

Paints and varnishes — Evaluation of
properties of coating systems related to
the application process —
Part 3:
Visual assessment of sagging, formation
of bubbles, pinholing and hiding power
Peintures et vernis — Évaluation des propriétés des systèmes de
revêtement liées au mode d'application —
Partie 3: Évaluation visuelle du festonnage, de la formation de bulles,
des piqûres et du pouvoir masquant




Reference number
ISO 28199-3:2009(E)
©
ISO 2009

---------------------- Page: 7 ----------------------

SIST EN ISO 28199-3:2010
ISO 28199-3:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 28199-3:2010
ISO 28199-3:2009(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Tendency toward sagging .1
4.1 General .1
4.2 Evaluation.3
5 Bubbles.3
5.1 General .3
5.2 Evaluation.3
6 Pinholing .3
6.1 General .3
6.2 Evaluation.3
7 Process hiding power .3
7.1 General .3
7.2 Evaluation.4
8 Test report.4
Annex A (informative) Examples of bubbles, pinholes and craters .
...