SIST EN 62196-2:2012
(Main)Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories (IEC 62196-2:2011)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories (IEC 62196-2:2011)
IEC 62196-2:2011 applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 500 V a.c., 50 to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This standard covers the basic interface accessories for vehicle supply as specified in IEC 62196-1, and intended for use in conductive charging systems for circuits specified in IEC 61851-1:2010. This publication is to be read in conjunction with IEC 62196-1:2011.
Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden von Elektrofahrzeugen - Teil 2: Anforderungen und Hauptmaße für die Kompatibilität und Austauschbarkeit von Stift- und Buchsensteckvorrichtungen für Wechselstrom (IEC 62196-2:2011)
Prises de courant et connecteurs de véhicule - Charge conductive de véhicules électriques - Partie 2: Règles de compatibilité et d'interchangeabilité dimensionnelle pour les appareils à broches et alvéoles pour courant alternatif (CEI 62196-2:2011)
La CEI 62196-2:2011 s'applique aux fiches, aux socles de prise de courant, aux prises mobiles et socles de connecteurs de véhicule, à broches et alvéoles, de configurations normalisées, ci-après dénommés appareils. Ces appareils ont une tension de service assignée ne dépassant pas 500 V c.a., 50 à 60 Hz, et un courant assigné ne dépassant pas 63 A en triphasé ou 70 A en monophasé, et sont destinés à la charge conductive des véhicules électriques. La présente norme couvre les appareils d'interface de base pour l'alimentation de véhicules tel que spécifié dans la CEI 62196-1 et destinés à être utilisés dans les systèmes de charge conductive pour des circuits spécifiés dans la CEI 61851-1:2010. Cette publication doit être lue conjointement avec la CEI 62196-1:2011.
Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih vozil - 2. del: Zahteve za dimenzijsko skladnost in zamenljivost pribora s trni in cevastimi kontakti za izmenični tok (a.c.) (IEC 62196-2:2011)
Ta standard se uporablja za vtiče, vtičnice, konektorje in uvodnice na vozilih s trni in cevastimi kontakti standardiziranih oblik (v nadaljnjem besedilu: »priključki«). Njihova nominalna nazivna obratovalna napetost je manjša od 500 V izmenične napetosti, nazivni tok pa manjši od 63 A pri treh fazah ali 70 A pri eni fazi za uporabo pri sistemih za kabelsko napajanje električnih vozil. Ta standard zajema osnovne vmesniške priključke za napajanje vozil, ki so določeni v standardu IEC 62196-1 in namenjeni za uporabo v sistemih za kabelsko napajanje za tokokroge iz standarda IEC 61851-1:2010. Izraz »električna vozila« se nanaša na vsa cestna vozila, vključno z hibridnimi cestnimi vozili z možnostjo napajanja prek navadne vtičnice (PHEV), ki vso energijo ali njen del pridobijo iz akumulatorjev v vozilu. Ti priključki so namenjeni za uporabo pri tokokrogih, navedenih v standardu IEC 61851-1:2010, ki delujejo pri različnih napetostih in frekvencah in lahko vključujejo malo napetost (ELV) in komunikacijske signale. Ti priključki se lahko uporabljajo za dvosmerni prenos energije (v obravnavi). Ta standard se uporablja za priključke, ki so namenjeni uporabi pri temperaturi okolja, in sicer med –30 °C in + 50 °C. Ti priključki se lahko priključijo samo na kable z vodniki iz bakra ali bakrene zlitine. Konektorji in uvodnice na vozilih iz tega standarda se lahko uporabljajo pri napajanju v načinu 1, 2 in 3, primera B in C. Vtičnice in vtiči iz tega standarda se lahko uporabljajo samo pri načinu napajanja 3, primera A in B. Načini in dovoljeni priključki so navedeni v 1. delu.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62196-2:2012
01-julij-2012
9WLþLYWLþQLFHNRQHNWRUMLLQXYRGQLFHQDYR]LOLK.DEHOVNRQDSDMDQMHHOHNWULþQLK
YR]LOGHO =DKWHYH]DGLPHQ]LMVNRVNODGQRVWLQ]DPHQOMLYRVWSULERUDVWUQLLQ
FHYDVWLPLNRQWDNWL]DL]PHQLþQLWRN DF ,(&
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of
electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements
for a.c. pin and contact-tube accessories (IEC 62196-2:2011)
Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden
von Elektrofahrzeugen - Teil 2: Anforderungen und Hauptmaße für die Kompatibilität und
Austauschbarkeit von Stift- und Buchsensteckvorrichtungen für Wechselstrom (IEC
62196-2:2011)
Prises de courant et connecteurs de véhicule - Charge conductive de véhicules
électriques - Partie 2: Règles de compatibilité et d'interchangeabilité dimensionnelle pour
les appareils à broches et alvéoles pour courant alternatif (CEI 62196-2:2011)
Ta slovenski standard je istoveten z: EN 62196-2:2012
ICS:
29.120.30 9WLþLYWLþQLFHVSRMNH Plugs, socket-outlets,
couplers
43.120 (OHNWULþQDFHVWQDYR]LOD Electric road vehicles
SIST EN 62196-2:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62196-2:2012
---------------------- Page: 2 ----------------------
SIST EN 62196-2:2012
EUROPEAN STANDARD
EN 62196-2
NORME EUROPÉENNE
May 2012
EUROPÄISCHE NORM
ICS 29.120.30; 43.120
English version
Plugs, socket-outlets, vehicle connectors and vehicle inlets -
Conductive charging of electric vehicles -
Part 2: Dimensional compatibility and interchangeability requirements for
a.c. pin and contact-tube accessories
(IEC 62196-2:2011)
Fiches, socles de prise de courant, prises Stecker, Steckdosen,
mobiles et socles de connecteurs de Fahrzeugkupplungen und
véhicule - Fahrzeugstecker -
Charge conductive des véhicules Konduktives Laden von
électriques - Elektrofahrzeugen -
Partie 2: Exigences dimensionnelles de Teil 2: Anforderungen und Hauptmaße für
compatibilité et d’interchangeabilité pour die Kompatibilität und Austauschbarkeit
les appareils à broches et alvéoles pour von Stift- und Buchsensteckvorrichtungen
courant alternatif für Wechselstrom
(CEI 62196-2:2011) (IEC 62196-2:2011)
This European Standard was approved by CENELEC on 2012-02-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62196-2:2012 E
---------------------- Page: 3 ----------------------
SIST EN 62196-2:2012
EN 62196-2:2012 - 2 -
Foreword
The text of document 23H/267/FDIS, future edition 1 of IEC 62196-2, prepared by SC 23H, "Industrial
plugs and socket-outlets", of IEC TC 23, "Electrical accessories" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN 62196-2:2012.
The following dates are fixed:
(dop) 2012-11-01
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-02-01
• latest date by which the national
standards conflicting with the
document have to be withdrawn
EN 62196-2 is to be read in conjunction with EN 62196-1. The clauses of the particular requirements in
Part 2 supplement or modify the corresponding clauses in Part 1. Where the text indicates an "addition" to
or a "replacement" of the relevant requirement, test specification or explanation of Part 1, these changes
are made to the relevant text of Part 1, which then becomes part of the standard. Where no change is
necessary, the words "This clause of Part 1 is applicable" are used.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed
for Use within Certain Voltage Limits (LVD - 2006/95/EC).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62196-2:2011 was approved by CENELEC as a European
Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 62196-2:2012
- 3 - EN 62196-2:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Addition to Annex ZA of EN 62196-1:2012:
Publication Year Title EN/HD Year
IEC 60068-2-14 - Environmental testing - EN 60068-2-14 -
Part 2-14: Tests - Test N: Change of
temperature
---------------------- Page: 5 ----------------------
SIST EN 62196-2:2012
EN 62196-2:2012 - 4 -
Annex ZB
(normative)
Special national conditions
Special national condition: National characteristic or practice that cannot be changed even over a long
period, e.g. climatic conditions, electrical earthing conditions.
NOTE If it affects harmonization, it forms part of the European Standard / Harmonization Document.
For the countries in which the relevant special national conditions apply these provisions are normative,
for other countries they are informative.
Clause Special national condition
1 Finland
In Finland, accessories and cable assemblies according to this standard are to be used in
an ambient temperature between –35 °C and +50 °C.
6.1 United Kingdom
Mode 1 is considered unsafe and will not be used in the United Kingdom.
10.101 France
nd
Add a 2 paragraph: When plugs & socket-outlets are used and socket-outlets are
accessible to uninstructed persons, they shall be provided with shutters (as presently
defined in Type 3).
__________
---------------------- Page: 6 ----------------------
SIST EN 62196-2:2012
IEC 62196-2
®
Edition 1.0 2011-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive
charging of electric vehicles –
Part 2: Dimensional compatibility and interchangeability requirements for a.c.
pin and contact-tube accessories
Fiches, socles de prise de courant, prises mobiles et socles de connecteurs de
véhicule – Charge conductive des véhicules électriques –
Partie 2: Exigences dimensionnelles de compatibilité et d’interchangeabilité
pour les appareils à broches et alvéoles pour courant alternatif
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX W
ICS 29.120.30; 43.120 ISBN 978-2-88912-731-3
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 62196-2:2012
– 2 – 62196-2 IEC:2011
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 General . 8
5 Ratings . 8
6 Connection between the power supply and the electric vehicle . 8
7 Classification of accessories . 11
8 Marking . 11
9 Dimensions . 11
10 Protection against electric shock . 12
11 Size and colour of earthing conductors . 12
12 Provision for earthing . 12
13 Terminals . 12
14 Interlocks . 13
15 Resistance to ageing of rubber and thermoplastic material . 13
16 General construction . 13
17 Construction of socket-outlets . 13
18 Construction of plugs and vehicle connectors . 13
19 Construction of vehicle inlets . 13
20 Degrees of protection . 13
21 Insulation resistance and dielectric strength . 13
22 Breaking capacity . 13
23 Normal operation . 14
24 Temperature rise . 14
25 Flexible cables and their connection . 14
26 Mechanical strength . 14
27 Screws, current-carrying parts and connections . 15
28 Creepage distances, clearances and distances . 15
29 Resistance to heat, to fire and to tracking . 15
30 Corrosion and resistance to rusting . 15
31 Conditional short-circuit current withstand test . 15
32 Electromagnetic compatibility (EMC) . 15
33 Vehicle driveover . 15
101 Components . 15
102 Coding resistors . 16
Table 101 – Overview of the basic vehicle interface, configuration Type 1, single
phase . 10
---------------------- Page: 8 ----------------------
SIST EN 62196-2:2012
62196-2 IEC:2011 – 3 –
Table 102 – Overview of the basic vehicle interface, configuration Types 2 and 3,
three-phase or single phase . 10
Table 103 – Configuration types and standard sheets . 12
---------------------- Page: 9 ----------------------
SIST EN 62196-2:2012
– 4 – 62196-2 IEC:2011
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
PLUGS, SOCKET-OUTLETS, VEHICLE CONNECTORS
AND VEHICLE INLETS –
CONDUCTIVE CHARGING OF ELECTRIC VEHICLES –
Part 2: Dimensional compatibility and interchangeability requirements
for a.c. pin and contact-tube accessories
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62196-2 has been prepared by IEC subcommittee 23H: Industrial
plugs and socket-outlets, of IEC technical committee 23: Electrical accessories.
The text of this standard is based on the following documents:
FDIS Report on voting
23H/267/FDIS 23H/270/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 10 ----------------------
SIST EN 62196-2:2012
62196-2 IEC:2011 – 5 –
A list of all the parts in the IEC 62196 series, under the general title Plugs, socket-outlets,
vehicle connectors and vehicle inlets – Conductive charging of electric vehicles, can be found
on the IEC website.
This part of IEC 62196 is to be read in conjunction with IEC 62196-1. The clauses of the
particular requirements in Part 2 supplement or modify the corresponding clauses in Part 1.
Where the text indicates an "addition" to or a "replacement" of the relevant requirement, test
specification or explanation of Part 1, these changes are made to the relevant text of Part 1,
which then becomes part of the standard. Where no change is necessary, the words "This
clause of Part 1 is applicable" are used.
In this standard, the following print types are used:
- compliance statements: in italic type.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 11 ----------------------
SIST EN 62196-2:2012
– 6 – 62196-2 IEC:2011
INTRODUCTION
Responding to global challenges of CO reduction and energy security, the automobile
2
industries have been accelerating the development and commercialization of electric vehicles
and hybrid electric vehicles. In addition to the prevailing hybrid electric vehicles, battery
electric vehicles including plug-in hybrid electric vehicles are going to be mass-marketed. To
support the diffusion of such vehicles, this standard provides the standard interface
configurations of a.c. vehicle couplers and accessories to be used in conductive charging of
electric vehicles, taking the most frequent charging situations into consideration.
IEC 62196 is divided into several parts:
Part 1: General requirements
Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-
tube accessories
Part 3: Dimensional compatibility and interchangeability requirements for pin and contact-tube
accessories for dedicated d.c. charging or for combined a.c./d.c.charging (under
consideration)
---------------------- Page: 12 ----------------------
SIST EN 62196-2:2012
62196-2 IEC:2011 – 7 –
PLUGS, SOCKET-OUTLETS, VEHICLE CONNECTORS
AND VEHICLE INLETS –
CONDUCTIVE CHARGING OF ELECTRIC VEHICLES –
Part 2: Dimensional compatibility and interchangeability requirements
for a.c. pin and contact-tube accessories
1 Scope
This standard applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins
and contact-tubes of standardized configurations, herein referred to as accessories. They
have a nominal rated operating voltage not exceeding 500 V a.c., 50 to 60 Hz, and a rated
current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging
of electric vehicles.
This standard covers the basic interface accessories for vehicle supply as specified in
IEC 62196-1, and intended for use in conductive charging systems for circuits specified in
IEC 61851-1:2010.
Electric vehicles covers all road vehicles, including plug-in hybrid road vehicles (PHEV), that
derive all or part of their energy from on-board batteries.
NOTE 1 These accessories may provide a contact that can be used for the proximity contact function.
These accessories are intended to be used for circuits specified in IEC 61851-1:2010 which
operate at different voltages and frequencies and which may include ELV and communication
signals.
These accessories may be used for bidirectional energy transmission (under consideration).
This standard applies to the accessories to be used in an ambient temperature of between
– 30 °C and + 50 °C.
NOTE 2 In the following country, other requirements may apply: FI.
These accessories are intended to be connected only to cables with copper or copper-alloy
conductors.
Vehicle inlet and vehicle connector to this standard are intended to be used for charging in
modes 1, 2 and 3, cases B and C. The socket-outlets and plugs covered by this standard are
intended to be used for charging mode 3 only, case A and B.
The modes and permissible connections are specified in Part 1.
2 Normative references
This clause of Part 1 is applicable except as follows:
Addition:
IEC 60068-2-14, Environmental testing – Part 2-14: Tests – Test N: Change of temperature
---------------------- Page: 13 ----------------------
SIST EN 62196-2:2012
– 8 – 62196-2 IEC:2011
3 Terms and definitions
This clause of Part 1 is applicable.
4 General
This clause of Part 1 is applicable, except as follows:
Addition at the end of the subclause:
Accessories according to this standard are intended for modes 1, 2 and 3, cases A to C. The
socket-outlets and plugs covered by this standard shall be used only in mode 3.
5 Ratings
This clause of Part 1 is applicable except as follows:
5.1 Replacement:
Rated operating voltage range:
0 to 30 V (signal or control purposes only);
200 to 250 V a.c.
380 to 480 V a.c.
5.2 Replacement:
2 A (signal or control purposes only)
13 A single phase
16 A single and three-phase
20 A single and three-phase
30-32 A single and three-phase
60-63 A single and three-phase
70 A single phase, only
NOTE In the following countries, the branch circuit overcurrent protection device is based upon 125 % of the
accessory rating: US.
6 Connection between the power supply and the electric vehicle
This clause of Part 1 is applicable except as follows:
6.1 Replacement:
This section provides a description of the physical conductive electrical interface
requirements between the vehicle and the power supply, which allows the following design at
the vehicle interface:
a basic interface that provides for current ratings up to 63 A a.c. three-phase and up to 70 A
a.c. single phase.
Different configuration types for the basic interface may allow different application of mode
and current ratings. See introduction to relevant standard sheets for more details.
---------------------- Page: 14 ----------------------
SIST EN 62196-2:2012
62196-2 IEC:2011 – 9 –
NOTE In the following country, Mode 1 will not be allowed: UK.
6.2 Replacement:
There shall be the following type of vehicle inlets:
basic
6.3 Replacement:
There shall be the following type of vehicle connectors:
basic
6.4 Not applicable
6.5 Replacement:
The basic interface may contain up to 7 power or signal contacts, with unique physical
configurations of contact positions for single or three phases. The electrical ratings and their
function are described in Table 101. The electrical ratings and their function are described in
the Standard Sheets.
Each vehicle inlet shall only mate with the corresponding type of vehicle connector. Each plug
shall only mate with the corresponding type of socket-outlet.
The accessories, configuration Types 1, 2 or 3 are rated as follows:
– configuration Type 1 vehicle coupler is rated 250 V, 32 A single phase;
– configuration Type 2 vehicle coupler, socket-outlet and plug are rated:
– 250 V, 13 A or 20 A or 32 A or 63 A or 70 A single phase,
– 380-480 V, 13 A or 20 A or 32 A or 63 A, three-phase.
– configuration Type 3 vehicle coupler is rated:
– 250 V, 16 A or 32 A, single phase,
– 380-480 V, 32 A, or 63 A three-phase.
– Configuration Type 3 socket-outlet and plug are rated:
– 250 V, 16 A or 32 A single phase,
– 380-480 V, 32 A, or 63 A three-phase.
---------------------- Page: 15 ----------------------
SIST EN 62196-2:2012
– 10 – 62196-2 IEC:2011
Table 101 – Overview of the basic vehicle interface,
configuration Type 1, single phase
a c
Position number a.c. Functions
b
1 250 V 32 A L1 (mains 1)
2 250 V 32 A L2 (mains 2)/N(neutral)
3 Rated for fault PE (ground/earth)
4 30 V 2 A CP (Control pilot)
5 30 V 2 A CS (Connection)
a
Position number does not refer to the location and/or identification of the contact in the
accessory.
b
In the following countries, the branch circuit overcurrent protection is based upon 125 % of
the device rating: USA.
c
For contacts 4 and 5, environmental conditions may demand larger conductor cross-
sections.
Table 102 – Overview of the basic vehicle interface,
configuration Types 2 and 3, three-phase or single phase
Three phase Single phase
a a
U I I
Position max max max
f Functions
number
V a.c. A A
b
Type 2 Type 3 Type 2 Type 3
b
1 480 63 70 63
L1 (mains 1)
c c
2 480 63 L2 (mains 2)
- -
c c
3 480 63 L3 (mains 3)
- -
b, e
4 480 63 70 63
N (neutral)
5 ― Rated for fault PE (ground/earth)
6 30 2 CP (Control pilot)
d
PP (Proximity) or
7 30 2 d
CS (Connection switch)
a
In the following countries, the branch circuit overcurrent protection is based upon 125 % of the device
rating: USA.
b
For single phase charging, contacts 1 and 4 shall be used.
c
Unused contacts need not to be installed. Not provided for standard sheets 2-IIIa and 2-IIIb.
d
Not provided for standard sheet 2-IIIa.
e
For single phase system supply phase to phase this contact can be used for L2 (mains 2).
f
Position number does not refer to the location and/or identification of the contact in the accessory
6.6 This subclause of Part 1 is not applicable.
6.101 Communication and control pilot function
The control pilot and proximity detection, or connection contacts shall be used in accordance
with IEC 61851-1:2010.
---------------------- Page: 16 ----------------------
SIST EN 62196-2:2012
62196-2 IEC:2011 – 11 –
7 Classification of accessories
This clause of Part 1 is applicable except as follows:
7.4 Replacement:
According to electrical operation
– Suitable for making and breaking an electrical circuit under load for configuration
Types 1 and 3 up to 32 A;
– Not suitable for making and breaking an electrical circuit under load for configurations
Type 2 rated 63 A and 70 A and Type 3, rated 63 A.
NOTE Communication circuits to this standard are deemed not to make or break load in the purpose of this clause.
7.5 Replacement:
According to the function as specified in Clause 6
– Basic type only.
Addition:
7.101 According to the Standard Sheet used
– Configuration Type 1;
– Configuration Type 2;
– Configuration Type 3.
8 Marking
This clause of Part 1 is applicable.
9 Dimensions
This clause of Part 1 is applicable except as follows:
9.1 Replacement:
Accessories shall comply with the relevant standard sheets as specified below and in Table
103:
Configuration Type 1
– Vehicle couplers not exceeding 250 V, 32 A single phase: standard sheet 2-I.
– Optional locking system: standard sheet 2-Ia.
NOTE In the USA, the standard sheets 2-I and 2-Ia may be applied to vehicle couplers with rated current up to
80 A.
Configuration Type 2
– Accessories not exceeding 480 V, 63 A three-phase or 70 A single phase: standard
sheets 2-II, IIa, IIb, IIc, IId, IIe, IIf, IIg and IIh.
Configuration Type 3
– Accessories not exceeding 250 V, 16 A single phase, one pilot: standard sheet 2-IIIa;
– Accessories not exceeding 250 V, 32 A single phase, two pilots: standard sheet 2-IIIb;
---------------------- Page: 17 ----------------------
SIST EN 62196-2:2012
– 12 – 62196-2 IEC:2011
– Accessories not exceeding 480 V, 63 A three phase, two pilots: standard sheet 2-IIIc;
– Retaini
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.