SIST EN 60749-9:2004

Semiconductor devices - Mechanical and climatic test methods -- Part 9: Permanence of marking

Aims at testing and verifying that the markings on semiconductor devices will not become illegible when subject to solvents or cleaning solutions commonly used during the removal of solder flux residue from the printed circuit board assembly process. This test is applicable for all package types. The test should be considered non-destructive.

Halbleiterbauelemente - Mechanische und klimatische Prüfverfahren -- Teil 9: Beständigkeit der Kennzeichnung

Dispositifs à semiconducteurs - Méthodes d'essais mécaniques et climatiques -- Partie 9: Permanence du marquage

Vise à vérifier que les marquages sur les dispositifs à semiconducteurs ne deviendront pas illisibles lorsqu'ils seront soumis aux solvants ou aux solutions de nettoyage normalement utilisés pour éliminer les résidus de flux de soudage produits pendant l'assemblage des cartes à circuits imprimés. Cet essai est applicable à tous les types de boîtiers. Il y a lieu de considérer cet essai comme non destructif.

Semiconductor devices - Mechanical and climatic test methods - Part 9: Permanence of marking (IEC 60749-9:2002)

General Information

• Status: Withdrawn
• Publication Date: 30-Jun-2004
• Withdrawal Date: 16-Jun-2020
• ICS: 31.080.01 - Semiconductor devices in general
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 17-Jun-2020
• Due Date: 10-Jul-2020
• Completion Date: 17-Jun-2020
• Ref Project: EN 60749-9:2002 - Semiconductor devices - Mechanical and climatic test methods - Part 9: Permanence of marking

Relations

• Replaced By: SIST EN 60749-9:2017 - Semiconductor devices - Mechanical and climatic test methods - Part 9: Permanence of marking (IEC 60749-9:2017)
• Effective Date: 20-Jun-2017
• Replaced By: SIST EN 60749-9:2017 - Semiconductor devices - Mechanical and climatic test methods - Part 9: Permanence of marking (IEC 60749-9:2017)
• Effective Date: 07-Jun-2022
• Replaces: SIST EN 60749:2002 + A1:2002 - Semiconductor devices - Mechanical and climatic test methods
• Effective Date: 28-Jan-2023
• Revised: SIST EN 60749:2002 + A1:2002 - Semiconductor devices - Mechanical and climatic test methods
• Effective Date: 13-May-2010
• Replaces: SIST EN 60749:2002 + A1:2002 - Semiconductor devices - Mechanical and climatic test methods
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI SIST EN 60749-9:2004

STANDARD
julij 2004
Semiconductor devices - Mechanical and climatic test methods - Part 9:
Permanence of marking (IEC 60749-9:2002)
ICS 31.080.01 Referenčna številka
SIST EN 60749-9:2004(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 60749-9
NORME EUROPÉENNE
EUROPÄISCHE NORM August 2002
ICS 31.080.01 Partly supersedes EN 60749:1999 + A1:2000 + A2:2001
English version
Semiconductor devices -
Mechanical and climatic test methods
Part 9: Permanence of marking
(IEC 60749-9:2002)
Dispositifs à semiconducteurs - Halbleiterbauelemente -
Méthodes d'essais mécaniques Mechanische und klimatische
et climatiques Prüfverfahren
Partie 9: Permanence du marquage Teil 9: Beständigkeit der Kennzeichnung
(CEI 60749-9:2002) (IEC 60749-9:2002)
This European Standard was approved by CENELEC on 2002-07-02. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60749-9:2002 E

---------------------- Page: 2 ----------------------

EN 60749-9:2002 - 2 -
Foreword
The text of document 47/1604/FDIS, future edition 1 of IEC 60749-9, prepared by IEC TC 47,
Semiconductor devices, was submitted to the IEC-CENELEC parallel vote and was approved by
CENELEC as EN 60749-9 on 2002-07-02.
This mechanical and climatic test method, as it relates to the permanence of marking, is a complete
rewrite of the test contained in clause 2, chapter 4 of EN 60749:1999.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2003-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2005-07-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60749-9:2002 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60749-9:2002
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60068-2-45 - Basic environmental testing procedures EN 60068-2-45 1992
Part 2: Tests - Test Xa and guidance:
Immersion in cleaning solvents

1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

NORME CEI
INTERNATIONALE IEC
60749-9
INTERNATIONAL
Première édition
STANDARD
First edition
2002-04
Dispositifs à semiconducteurs –
Méthodes d'essais mécaniques et climatiques –
Partie 9:
Permanence du marquage
Semiconductor devices –
Mechanical and climatic test methods –
Part 9:
Permanence of marking
 IEC 2002 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail]  Web: www.iec.ch
CODE PRIX
E
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
Международная Электротехническая Комиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 5 ----------------------

60749-9  IEC:2002 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SEMICONDUCTOR DEVICES –
MECHANICAL AND CLIMATIC TEST METHODS –
Part 9: Permanence of marking
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility tha
...