SIST EN ISO 11343:2005
(Main)Adhesives - Determination of dynamic resistance to cleavage of high-strength adhesive bonds under impact conditions - Wedge impact method (ISO 11343:2003)
Adhesives - Determination of dynamic resistance to cleavage of high-strength adhesive bonds under impact conditions - Wedge impact method (ISO 11343:2003)
This Standard specifies a dynamic impact wedge method for the determination of the cleavage resistance under impact loading ofhigh- strength adhesive bonds between two metallic adherends, when tested under specified conditions of preparation and testing. This test procedure does not provide design information. The method allows a choice of sheet metal substrate corresponding to those materials frequently used in industry, e.g. for automotive applications.
Klebstoffe - Bestimmung des dynamischen Keil-Schlag-Widerstandes von hochfesten Klebungen unter Schlagbelastung - Keil-Schlag-Verfahren (ISO 11343:2003)
Diese Internationale Norm legt ein dynamisches Keil-Schlag-Verfahren für die Bestimmung des Keil-Schlag-Widerstandes unter Schlagbelastung hochfester Klebungen zwischen zwei metallischen Fügeteilen, die unter festgelegten Bedingungen hergestellt und geprüft werden, fest. Dieses Verfahren liefert keine Informationen für die Konstruktion.
Dieses Verfahren gestattet, Metallbleche zu wählen, die in der Industrie, z. B. für Automobilbau, eingesetzt werden.
Adhésifs - Détermination de la résistance dynamique au clivage de joints collés a haute résistance soumis aux conditions d'impact - Méthode d'impact au coin (ISO 11343:2003)
L'ISO 11343:2003 spécifie une méthode d'essai d'impact au coin pour la détermination de la résistance au clivage d'adhésifs à haute résistance soumis à une charge dynamique entre deux supports métalliques collés, dans des conditions spécifiées de préparation et d'essai. Ce mode opératoire d'essai ne fournit pas d'informations relatives à la conception.
La méthode permet le choix du substrat métallique en plaques correspondant aux matériaux généralement utilisés dans l'industrie, par exemple l'industrie automobile.
Lepila - Ugotavljanje dinamične odpornosti proti cepitvi lepljenih spojev z veliko trdnostjo pod udarnimi pogoji - Metoda z udarnim klinom (ISO 11343:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11343:2005
01-julij-2005
/HSLOD8JRWDYOMDQMHGLQDPLþQHRGSRUQRVWLSURWLFHSLWYLOHSOMHQLKVSRMHY]YHOLNR
WUGQRVWMRSRGXGDUQLPLSRJRML0HWRGD]XGDUQLPNOLQRP ,62
Adhesives - Determination of dynamic resistance to cleavage of high-strength adhesive
bonds under impact conditions - Wedge impact method (ISO 11343:2003)
Klebstoffe - Bestimmung des dynamischen Keil-Schlag-Widerstandes von hochfesten
Klebungen unter Schlagbelastung - Keil-Schlag-Verfahren (ISO 11343:2003)
Adhésifs - Détermination de la résistance dynamique au clivage de joints collés a haute
résistance soumis aux conditions d'impact - Méthode d'impact au coin (ISO 11343:2003)
Ta slovenski standard je istoveten z: EN ISO 11343:2005
ICS:
83.180 Lepila Adhesives
SIST EN ISO 11343:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11343:2005
---------------------- Page: 2 ----------------------
SIST EN ISO 11343:2005
EUROPEAN STANDARD
EN ISO 11343
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2005
ICS 83.180 Supersedes EN 14493:2002
English version
Adhesives - Determination of dynamic resistance to cleavage of
high-strength adhesive bonds under impact conditions - Wedge
impact method (ISO 11343:2003)
Adhésifs - Détermination de la résistance dynamique au Klebstoffe - Bestimmung des dynamischen Keil-Schlag-
clivage de joints collés à haute résistance soumis aux Widerstandes von hochfesten Klebungen unter
conditions d'impact - Méthode d'impact au coin (ISO Schlagbelastung - Keil-Schlag-Verfahren (ISO 11343:2003)
11343:2003)
This European Standard was approved by CEN on 29 April 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11343:2005: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11343:2005
EN ISO 11343:2005 (E)
Foreword
The text of ISO 11343:2003 has been prepared by Technical Committee ISO/TC TC 61 "Plastics"
of the International Organization for Standardization (ISO) and has been taken over as EN ISO
11343:2005 by Technical Committee CEN/TC 193 "Adhesives", the secretariat of which is held by
AENOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by November 2005, and conflicting national
standards shall be withdrawn at the latest by November 2005.
This document supersedes EN 14493:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 11343:2003 has been approved by CEN as EN ISO 11343:2005 without any
modifications.
Safety:
Persons using this standard shall be familiar with normal laboratory practice.
This standard does not purport to address all the safety problems, if any, associated with its use.
It is the responsibility of the user to establish safety and health practices and to ensure
compliance with any European or national regulatory conditions.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11343:2005
INTERNATIONAL ISO
STANDARD 11343
Second edition
2003-04-01
Adhesives — Determination of dynamic
resistance to cleavage of high-strength
adhesive bonds under impact
conditions — Wedge impact method
Adhésifs — Détermination de la résistance dynamique à un clivage de
joints collés à haute résistance soumis aux conditions d'impact —
Méthode d'impact au coin
Reference number
ISO 11343:2003(E)
©
ISO 2003
---------------------- Page: 5 ----------------------
SIST EN ISO 11343:2005
ISO 11343:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 11343:2005
ISO 11343:2003(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Principle . 2
5 Apparatus. 2
6 Specimens . 3
7 Test procedure . 6
8 Expression of results. 7
9 Precision . 7
10 Test report. 7
© ISO 2003 — All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 11343:2005
ISO 11343:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11343 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This second edition cancels and replaces the first edition (ISO 11343:1993), which has been technically
revised.
iv © ISO 2003 — All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11343:2005
INTERNATIONAL STANDARD ISO 11343:2003(E)
Adhesives — Determination of dynamic resistance to cleavage
of high-strength adhesive bonds under impact conditions —
Wedge impact method
1 Scope
This International Standard specifies a dynamic impact wedge method for the determination of the cleavage
resistance under impact loading of high-strength adhesive bonds between two metallic adherends, when
tested under specified conditions of preparation and testing. This test procedure does not provide design
information.
The method allows a choice of sheet metal substrate corresponding to those materials frequently used in
industry, e.g. for automotive applications.�
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 291:1997, Plastics — Standard atmospheres for conditioning and testing
ISO 10365:1992, Adhesives — Designation of main failure patterns
1)
EN 13887:— , Structural adhesives — Guidelines for surface prepar
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.