SIST EN 301 021 V1.5.1:2003

Fixed Radio Systems; Point-to-multipoint equipment; Time Division Multiple Access (TDMA); Point-to-multipoint digital radio systems in frequency bands in the range 3 GHz to 11 GHz

To incorporate new classes to use the channel spacing in accordance with the ERC p-mp recommendations

Fiksni radijski sistemi – Oprema tipa točka-več točk – Časovno porazdeljeni sodostop (TDMA) – Digitalni radijski sistem tipa točka-več točk v frekvenčnih pasovih v območju od 3 GHz do 11 GHz

General Information

• Status: Published
• Publication Date: 30-Nov-2003
• ICS: 33.060.30 - Radio relay and fixed satellite communications systems
• Technical Committee: SS EIT - Technical Board for the electrotechnical, information technology and telecommunications fields
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Dec-2003
• Due Date: 01-Dec-2003
• Completion Date: 01-Dec-2003
• Ref Project: ETSI EN 301 021 V1.5.1 (2002-02) - Fixed Radio Systems; Point-to-multipoint equipment; Time Division Multiple Access (TDMA); Point-to-multipoint digital radio systems in frequency bands in the range 3 GHz to 11 GHz

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.UD]GHOMHQLFixed Radio Systems; Point-to-multipoint equipment; Time Division Multiple Access (TDMA); Point-to-multipoint digital radio systems in frequency bands in the range 3 GHz to 11 GHz33.060.30Radiorelejni in fiksni satelitski komunikacijski sistemiRadio relay and fixed satellite communications systemsICS:Ta slovenski standard je istoveten z:EN 301 021 Version 1.5.1SIST EN 301 021 V1.5.1:2003en01-december-2003SIST EN 301 021 V1.5.1:2003SLOVENSKI
STANDARD



SIST EN 301 021 V1.5.1:2003



ETSI EN 301 021 V1.5.1 (2002-02)European Standard (Telecommunications series) Fixed Radio Systems;Point-to-multipoint equipment;Time Division Multiple Access (TDMA);Point-to-multipoint digital radio systemsin frequency bands in the range 3 GHz to 11 GHz SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)2
Reference REN/TM-04125 Keywords DRRS, multipoint, radio, TDMA, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]
Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: [e-mail] Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2002. All rights reserved.
SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)3 Contents Intellectual Property Rights.5 Foreword.5 Introduction.5 1 Scope.7 1.1 Applications.7 1.2 Frequencies.7 1.3 Access method.7 2 References.8 3 Definitions, symbols and abbreviations.10 3.1 Definitions.10 3.2 Symbols.10 3.3 Abbreviations.10 4 General system architecture.11 4.1 Sub-system types.11 4.2 System characteristics.12 4.2.1 System capacity.12 4.2.2 Transmission error performance.12 4.2.3 Round trip delay for speech services.13 4.2.4 Transparency.13 4.2.5 Synchronization.13 5 Radio characteristics.13 5.1 Frequency bands.13 5.2 Proposed channel arrangements.13 5.3 Transmitter (tx) characteristics.14 5.3.1 Tx power range.14 5.3.2 Automatic Transmit Power Control (ATPC).15 5.3.3 Spectrum masks.15 5.3.3.1 Spectrum density mask.15 5.3.3.2 Discrete CW components exceeding the spectrum mask limit (all stations).21 5.3.4 Transmitter spurious emissions.22 5.3.4.1 Spurious emissions - external.22 5.3.4.2 Spurious emissions - internal.22 5.3.5 Radio frequency tolerance.23 5.4 Receiver characteristics.23 5.4.1 Input level range.23 5.4.2 Spurious emissions.23 5.4.2.1 Spurious emissions - external.23 5.4.2.2 Spurious emissions - internal.23 5.4.3 Bit Error Rate (BER) performance.23 5.4.4 Interference sensitivity.25 5.4.4.1 Adjacent channel interference.25 5.4.4.1.1 All system types excluding HC.25 5.4.4.1.2 System type HC.25 5.4.4.2 Co-channel interference.25 5.4.4.2.1 All system types excluding HC.25 5.4.4.2.2 System type HC.26 5.4.4.3 CW interference.26 5.4.5
Equipment Residual BER (RBER).26 5.4.6 Image frequency rejection.26 5.5 Antenna port characteristics.27 5.5.1 RF interface.27 5.5.2 Return loss.27 SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)4 6 Types of user equipment and service node interfaces.27 7 Power supply and environmental characteristics.28 7.1 Power supply.28 7.2 Environmental conditions.28 7.2.1 Equipment within weather protected locations.28 7.2.2 Equipment for non-weather protected locations.28 7.3 ElectroMagnetic Compatibility (EMC) conditions.28 Annex A (normative): System type codes for regulatory procedures.29 Annex B (informative): Example of Calculated Performance Against Tabulated Values.32 Annex C (informative): Bibliography.33 History.34
SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmission and Multiplexing (TM).
National transposition dates Date of adoption of this EN: 8 February 2002 Date of latest announcement of this EN (doa): 31 May 2002 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 November 2002 Date of withdrawal of any conflicting National Standard (dow): 30 November 2002
Introduction The main field of application of Point-to-Multipoint (P-MP) systems is to provide access to both public and private networks (Public Switched Telephone Networks (PSTN), Private Data Networks (PDN)). By means of P-MP systems the network service area may be extended to cover both distant and scattered user locations; and the systems may be applied to build new access networks covering both urban and rural areas. Users are offered the full range of services by the particular public or private network. Users have access to these services by means of the various standardized user network interfaces (2 wire loop, new data services and Integrated Services Digital Network (ISDN) ranging from basic rate to n x primary rate). P-MP systems provide standard network interfaces and transparently connect users to the appropriate network node. These systems allow a service to be connected to a number of users ranging from a few to several thousands and over a wide range of distances. P-MP systems are generally configured as Pre-Assigned Multiple Access (PAMA) radio systems or as Demand Assigned Multiple Access (DAMA) radio systems. The essential features of a typical P-MP radio system are: - efficient use of the radio spectrum; - concentration; - transparency. SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)6 Radio is often the ideal way of obtaining communications at low cost and almost independent of distance, and over difficult topography. Moreover, a small number of sites are required for these installations, thus facilitating rapid implementation and minimizing maintenance requirements of the systems. Concentration means that "m" users can share "n" radio channels (m being larger than n), allowing a better use to be made of the available frequency spectrum and at a lower equipment cost. The term "multi-access" derives from the fact that every user has access to every channel (instead of a fixed assignment as in most multiplex systems). When a demand arises an available channel (or channels) is allocated to it. When the demand is terminated, the channel is released for other use. Concentration requires the use of distributed intelligent control, which in turn allows many other operation and maintenance functions to be added. Transparency means that the network node and the user terminal communicate with each other without being aware of the radio path. Efficient use of the radio spectrum is generally achieved by reusing frequency sets at base stations in a cellular pattern. SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)7 1 Scope The present document covers equipment, which may operate in frequency bands that have paired frequencies, which can be used by either equipment employing Frequency Division Duplex (FDD) or Time Division Duplex (TDD) techniques. For use with Time Division Duplex only one frequency of the frequency pair will be used and for the purpose of the present document the tx/rx separation will be zero. The present document contains a revision to allow flexible channel spacings where block assignments have been made in accordance with ERC P-MP recommendations. Nevertheless, the channel spacing is intended be the same in
down-link and up-link directions. 1.1 Applications The present document specifies the minimum and optional requirements for system parameters of Time Division Multiple Access (TDMA) Point-to-Multipoint (P-MP) Radio Systems in the terrestrial Fixed Service operating in frequency bands in the range 3 GHz to 11 GHz. The present document covers the following typical Point-to-Multipoint (P-MP) applications: - voice;
- fax; - voice-band data; - telex, related to analogue interfaces; - data up to 64 kbit/s or beyond with optional interfaces; - ISDN; - digital video; - digital audio, related to digital interfaces. Radio terminals from different manufacturers are not intended to inter-work at radio frequency (i.e. no common air interface). The present document defines the requirements of radio terminal and radio-relay equipment including the interfaces. The requirements for multiplex, network management and antenna/feeder equipment may be addressed elsewhere. Testing to the present document will be undertaken with the guidance of a generic test methods document EN 301 126 [22], [23] and [24]. 1.2 Frequencies The present document covers fixed P-MP services operating in the 3,5 GHz, 3,7 GHz and 10,5 GHz bands, having the frequency plans as given in ERC Recommendations 14-03 [7], 12-08 [25], 12-05 [8] and in ITU-R Recommendation F.1189-1 [34]. 1.3 Access method The present document covers Time Division Multiple Access (TDMA) systems. SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)8 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. [1] ETSI ETS 300 012 (1992): "Integrated Services Digital Network (ISDN); Basic user-network interface Layer 1 specification and test principles". [2] ITU-T Recommendation G.703: "Physical/electrical characteristics of hierarchical digital interfaces". [3] ITU-T Recommendation Q.553 (1996): "Transmission characteristics at 4-wire analogue interfaces of digital exchanges". [4] ITU-T Recommendation Q.552 (1996): "Transmission characteristics at 2-wire analogue interfaces of digital exchange". [5] ITU-T Recommendation G.821: "Error performance of an international digital connection operating at a bit rate below the primary rate and forming part of an integrated services digital network". [6] ITU-T Recommendation R.20: "Telegraph modem for subscriber lines". [7] CEPT/ERC Recommendation 14-03: "Harmonised radio frequency channel arrangements for low and medium capacity systems in the band 3 400 MHz to 3 600 MHz". [8] CEPT/ERC Recommendation 12-05: "Harmonised radio frequency channel arrangements for digital terrestrial fixed systems operating in the band 10.0 - 10.68 GHz". [9] ETSI ETS 300 019-1 (1994): "Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; sub-parts 1-1 to 1-7: Classification of environmental conditions". [10] ETSI ETS 300 019-2 (1994): "Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; sub-parts 2-1 to 2-7: Specification of environmental tests". [11] ETSI ETS 300 132: "Equipment Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 1: Operated by alternating current (ac)derived from direct current sources; and Part 2: Operated by direct current (dc)". [12] ETSI EN 301 489-1: "Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements". [13] ETSI EN 301 489-4: "Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 4: Specific conditions for fixed radio links and ancillary equipment and services". [14] ETSI EN 300 385: "Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for fixed radio links and ancillary equipment". [15] ITU-T Recommendation G.726: "40, 32, 24, 16 kbit/s adaptive differential pulse code modulation (ADPCM)". [16] ITU-T Recommendation G.728: "Coding of speech at 16 kbit/s using low-delay code excited linear prediction". SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)9 [17] ITU-R Recommendation F.697-2: "Error performance and availability objectives for the local-grade portion at each end of an ISDN connection at a bit rate below the primary rate utilizing digital radio-relay systems". [18] ITU-T Recommendation G.729: "Coding of speech at 8 kbit/s using conjugate-structure algebraic-code-excited linear-prediction (CS-ACELP)". [19] ETSI EN 300 324: "V interfaces at the digital Local Exchange (LE); V5.1 interfaces for the support of Access Network (AN)". [20] ETSI ETS 300 347: "Signalling Protocols and Switching (SPS); V interfaces at the digital Local Exchange (LE) V5.2 interface for the support of Access Network (AN)". [21] ITU-R Recommendation F.1191: "Bandwidths and unwanted emissions of digital fixed service systems". [22] ETSI EN 301 126-2-1: "Fixed Radio Systems; Conformance testing; Part 2-1: Point-to-Multipoint equipment; Definitions and general requirements". [23] ETSI EN 301 126-2-3: "Fixed Radio Systems; Conformance testing; Part 2-3: Point-to-Multipoint equipment; Test procedures for TDMA systems". [24] ETSI EN 301 126-3-2: "Fixed Radio Systems; Conformance testing; Part 3-2: Point-to-Multipoint antennas - Definitions, general requirements and test procedures". [25] CEPT/ERC Recommendation 12-08: "Harmonized radio frequency channel arrangements and blocks allocations for low, medium and high capacity systems in the band 3 600 MHz to
4 200 MHz". [26] ITU-T Recommendation G.131: "Control of talker echo". [27] ETSI EN 300 011: "Integrated Services Digital Network (ISDN); Primary rate User-Network Interface (UNI); Part 1: Layer 1 specification". [28] ISO/IEC 8802-3: "Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications". [29] CEPT/ERC Recommendation 74-01: "Spurious emissions". [30] ITU-R Recommendation SM.329: "Spurious emissions". [31] ITU-R draft new Recommendation [9/1005]: "Frequency block arrangements for fixed wireless access (FWA) systems in the range 3 400-3 800 MHz". [32] ITU-T Recommendation G.826: "Error performance parameters and objectives for international, constant bit rate digital paths at or above the primary rate". [33] ITU-T Recommendation G.827: "Availability parameters and objectives for path elements of international constant bit-rate digital paths at or above the primary rate". [34] ITU-R Recommendation F.1189-1: "Error performance objectives for constant bit rate digital paths at or above the primary rate carried by digital radio-relay systems which may form part or all of the national portion of a 27 500 km hypothetical reference path". [35] ITU-R Recommendation F.557-4: "Availability objective for radio-relay systems over a hypothetical reference circuit and a hypothetical reference digital path". [36] ITU-T Recommendation G.723.1: "Speech coders: Dual rate speech coder for multimedia communications transmitting at 5.3 and 6.3 kbit/s". [37] ETSI EG 202 306 (V1.2.1): "Transmission and Multiplexing (TM); Access networks for residential customers". [38] ITU-T Recommendation G.711: "Pulse code modulation (PCM) of voice frequencies". SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)10 [39] ITU-T Recommendation G.957: "Optical interfaces for equipments and systems relating to the synchronous digital hierarchy". [40] ITU-R Radio Regulations: "Frequency allocations". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following term and definition apply: gross bit rate: defined as the transmission bit rate over the air NOTE: In case of a transmitter working in burst mode the gross bit rate is the instantaneous maximum transmission bit rate during the burst. The gross bit rate has a unique relationship to the symbol rate through the implemented modulation format. 3.2 Symbols For the purposes of the present document, the following symbols apply: ∆F Channel Spacing dB deciBel dBm deciBel relative to 1 milliwatt GHz GigaHertz Hz Hertz kbit/s kilobits per second kHz kiloHertz Mbit/s Megabits per second MHz MegaHertz ms millisecond 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: BER Bit Error Rate CCS Central Controller Station CRS Central Radio Station CS Central Station EMC ElectroMagnetic Compatibility ERC European Radiocommunications Committee HC High Coexistence ISDN Integrated Services Digital Network LD CELP Low Delay Code Excited Linear Prediction MGBR Minimum Gross Bit Rate MOS Mean Opinion Score OFDM Orthogonal Frequency Division Multiplexing PRBS Pseudo-Random Binary Sequence QDU Quantization Distortion Unit RBER Residual BER RS Repeater Station rx Receiver TDMA Time Division Multiple Access TE Terminal Equipment TS Terminal Station tx Transmitter SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)11 4 General system architecture 4.1 Sub-system types A system could consist of several sub-systems as follows (see figure 1): CSCCSCRSAnother CRS may beconnected to the same CCSSNIUNINetwork NodeUNIBaseband interface reference points SNI/UNIDirectional antennaOmnidirectional orsector antennaUNIUNIUNIUNITETETETETETETETSRSTSTSTSTS Figure 1: General system architecture CS: The Central Station, which interfaces the network. It can be integrated or divided into two units: - the Central Controller Station (CCS) also called the exchange unit which is the interface to the local switch; - the Central Radio Station (CRS) also called the radio unit, which is the central baseband/radio transceiver equipment. One CCS may control more than one CRS. TS: The Terminal Station (outstations with subscriber interfaces). A TS may serve more than one Terminal Equipment (TE). RS: The Repeater Station (radio repeater outstations with or without subscriber interfaces). An RS may serve one or more TS. TE: Terminal equipment. SNI: Service Node Interface (see EG 202 306 [37]). UNI: User Network Interface (see EG 202 306 [37]). SIST EN 301 021 V1.5.1:2003



ETSI ETSI EN 301 021 V1.5.1 (2002-02)12 The central station performs the interconnection with the network node carrying out a concentration function by sharing the total number of available channels in the system. The central station is linked either directly to all Terminal Stations or via Repeater Stations (RS) by microwave transmission paths. Whenever an existing digital transmission link is available, separating the CCS installed at the network node site and the CRS can optimize the network implementation. The general characteristics, which are typical for P-MP systems, are considered in the present document. These characteristics have been categories under four headings: 1) system characteristics; 2) radio characteristics; 3) type of services/user equipment and network interfaces; 4) power supply, mechanical and environmental characteristics. 4.2 System characteristics The following characteristics shall be used. 4.2.1 System capacity The present document defines eight System Types A, B C, D, E, F, G and HC. These systems represent different spectral efficiency in term of gross-bit-rate/Hz; the gross bit rate, defined in clause 3.3, has a unique relation to the symbol rate through the implemented modulation format: - A, E: lower complexity modulation formats (e.g. 4 states or equivalent); - HC: lower complexity modulation formats as System Type A (e.g. 4 states or equivalent), but with higher requirements for receiver sensitivity and tolerance to interference; - B and F: medium complexity modulation formats (e.g. 16 states or equivalent); - C: lower complexity modulation formats (e.g. 4 states or equivalent) for systems with a gross bit rate below 2 Mbit/s and limited to TDD operation only; - D and G: higher complexity modulation formats (e.g. 64 states or equivalent). The E, F and G system types are intended for OFDM modulation. The minimum gross bit rates for different channel spacing and system types are given in clause 5.2. The manufacturer shall declare the actual system traffic carrying capacity, the gross bit rate and the System Type. 4.2.2 Transmission error performance Equipment with system rate lower than 32 × 64 kbit/s or equivalent, shall be designed in order to meet network performance and availability requirements specified by ITU-T Recommendation G.821 [5] following the criteria defined in ITU-R Recommendation F.697-2 [17] for the local grade portion of the digital connection. Equipment with system rate equal
...