SIST EN 61557-7:2007
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures -- Part 7: Phase sequence
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures -- Part 7: Phase sequence
This part of IEC 61557 specifies the requirements for measuring equipment applied to testing the phase sequence in three-phase distribution systems. Indication of the phase sequence may be mechanical, visual and/or audible. This part of IEC 61557 does not apply to ancillary measuring equipment for other quantities, for example voltage testers comprising an additional phase sequence indicator. It does not apply to monitoring relays. This second edition cancels and replaces the first edition published in 1997. This edition constitutes a minor revision.
Elektrische Sicherheit in Niederspannungsnetzen bis AC 1 000 V und DC 1 500 V - Geräte zum Prüfen, Messen oder Überwachen von Schutzmaßnahmen -- Teil 7: Drehfeld
Sécurité électrique dans les réseaux de distribution basse tension de 1 000 V c.a. et 1 500 V c.c. - Dispositifs de contrôle, de mesure ou de surveillance de mesures de protection -- Partie 7: Ordre de phases
La présente partie de la CEI 61557 définit les exigences applicables aux appareils de mesure destinés à contrôler l'ordre des phases dans des réseaux de distribution triphasés. Le dispositif d´affichage de l'ordre des phases peut être mécanique, optique et/ou acoustique. La présente partie de la CEI 61557 ne couvre pas les dispositifs supplémentaires de mesure, par exemple des indicateurs de tension destinés à mesurer d´autres grandeurs. Elle ne s'applique pas aux relais de surveillance. Cette deuxième édition annule et remplace la première édition publiée en 1997. Cette édition constitue une révision mineure.
Električna varnost v nizkonapetostnih razdelilnih sistemih izmenične napetosti do 1 kV in enosmerne napetosti do 1,5 kV - Oprema za preskušanje, merjenje ali nadzorovanje zaščitnih ukrepov - 7. del: Fazno zaporedje (IEC 61557-7:2007)
Ta del IEC 61557 poudarja zahteve za merjenje opreme, ki se nanašajo na preskušanje faznega zaporedja v trifaznem distribucijskem sistemu. Indikacija faznega zaporedja je lahko mehanska, vidna in/ali slišna.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61557-7:2007
01-september-2007
1DGRPHãþD
SIST EN 61557-7:2000
(OHNWULþQDYDUQRVWYQL]NRQDSHWRVWQLKUD]GHOLOQLKVLVWHPLKL]PHQLþQHQDSHWRVWLGR
N9LQHQRVPHUQHQDSHWRVWLGRN92SUHPD]DSUHVNXãDQMHPHUMHQMHDOL
QDG]RURYDQMH]DãþLWQLKXNUHSRYGHO )D]QR]DSRUHGMH ,(&
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. -
Equipment for testing, measuring or monitoring of protective measures -- Part 7: Phase
sequence
Elektrische Sicherheit in Niederspannungsnetzen bis AC 1000 V und DC 1500 V –
Geräte zum Prüfen, Messen oder Überwachen von Schutzmaßnahmen – Teil 7: Drehfeld
Sécurité électrique dans les réseaux de distribution basse tension de 1 000 V c.a. et 1
500 V c.c. - Dispositifs de contrôle, de mesure ou de surveillance de mesures de
protection -- Partie 7: Ordre de phases
Ta slovenski standard je istoveten z: EN 61557-7:2007
ICS:
17.220.20 0HUMHQMHHOHNWULþQLKLQ Measurement of electrical
PDJQHWQLKYHOLþLQ and magnetic quantities
29.080.01 (OHNWULþQDL]RODFLMDQD Electrical insulation in
VSORãQR general
29.240.01 2PUHåMD]DSUHQRVLQ Power transmission and
GLVWULEXFLMRHOHNWULþQHHQHUJLMH distribution networks in
QDVSORãQR general
SIST EN 61557-7:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 61557-7
NORME EUROPÉENNE
March 2007
EUROPÄISCHE NORM
ICS 17.220.20; 29.080.01; 29.240.01 Supersedes EN 61557-7:1997
English version
Electrical safety in low voltage distribution systems
up to 1 000 V a.c. and 1 500 V d.c. -
Equipment for testing, measuring or monitoring
of protective measures -
Part 7: Phase sequence
(IEC 61557-7:2007)
Sécurité électrique dans les réseaux Elektrische Sicherheit
de distribution basse tension in Niederspannungsnetzen
de 1 000 V c.a. et 1 500 V c.c. - bis AC 1000 V und DC 1500 V -
Dispositifs de contrôle, de mesure Geräte zum Prüfen,
ou de surveillance de mesures Messen oder Überwachen
de protection - von Schutzmaßnahmen -
Partie 7: Ordre de phases Teil 7: Drehfeld
(CEI 61557-7:2007) (IEC 61557-7:2007)
This European Standard was approved by CENELEC on 2007-03-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61557-7:2007 E
---------------------- Page: 2 ----------------------
EN 61557-7:2007 - 2 -
Foreword
The text of document 85/295/FDIS, future edition 2 of IEC 61557-7, prepared by IEC TC 85, Measuring
equipment for electrical and electromagnetic quantities, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as EN 61557-7 on 2007-03-01.
This European Standard supersedes EN 61557-7:1997.
This standard is to be used in conjunction with EN 61557-1.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-12-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-03-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61557-7:2007 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 3 ----------------------
- 3 - EN 61557-7:2007
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60417 Data- Graphical symbols for use on equipment - -
base
1)
IEC/TR - Safety requirements for electrical equipment - -
61010-3-031 for measurement, control, and laboratory
use -
Part 3-031: Conformity verification report for
IEC 61010-031:2002 - Safety requirements
for hand-held probe assemblies for electrical
test and measurement
1) 2)
IEC 61557-1 - Electrical safety in low voltage distribution EN 61557-1 2007
systems up to 1 000 V a.c. and 1 500 V d.c. -
Equipment for testing, measuring or
monitoring of protective measures -
Part 1: General requirements
1)
Undated reference.
2)
Valid edition at date of issue.
---------------------- Page: 4 ----------------------
NORME CEI
INTERNATIONALE
IEC
61557-7
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2007-01
Sécurité électrique dans les réseaux
de distribution basse tension de 1 000 V c.a.
et 1 500 V c.c. –
Dispositifs de contrôle, de mesure ou de
surveillance de mesures de protection –
Partie 7: Ordre de phases
Electrical safety in low voltage distribution
systems up to 1 000 V a.c. and 1 500 V d.c. –
Equipment for testing, measuring
or monitoring of protective measures –
Part 7: Phase sequence
© IEC 2007 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
J
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 5 ----------------------
61557-7 © IEC:2007 – 3 –
CONTENTS
FOREWORD.5
1 Scope.9
2 Normative references.9
3 Terms and definitions .9
4 Requirements .9
5 Marking and operating instructions.11
5.1 Marking .11
5.2 Operating instructions.13
6 Tests .13
Annex A (normative) Illustrations for mechanical tests .17
Figure A.1 – Mechanical shock test .17
Figure A.2 – Drop test .17
---------------------- Page: 6 ----------------------
61557-7 © IEC:2007 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS
UP TO 1 000 V a.c. AND 1 500 V d.c. –
EQUIPMENT FOR TESTING, MEASURING OR MONITORING
OF PROTECTIVE MEASURES –
Part 7: Phase sequence
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional
...
SLOVENSKI oSIST prEN 61557-7:2005
PREDSTANDARD
november 2005
Električna varnost v nizkonapetostnih razdelilnih sistemih izmenične
napetosti do 1 kV in enosmerne napetosti do 1,5 kV – Oprema za preskušanje,
merjenje ali nadzorovanje zaščitnih ukrepov – 7. del: Fazno zaporedje
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V
d.c. – Equipment for testing, measuring or monitoring of protective measures – Part
7: Phase sequence
ICS 17.220.20 Referenčna številka
oSIST prEN 61557-7:2005(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
85/274/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJET DE COMITÉ POUR VOTE (CDV)
Project number IEC 61557-7 Ed. 2.0
Numéro de projet
IEC/TC or SC: Date of circulation Closing date for voting (Voting
TC 85
Date de diffusion mandatory for P-members)
CEI/CE ou SC:
Date de clôture du vote (Vote
2005-07-29
obligatoire pour les membres (P))
2006-01-06
Titre du CE/SC: Equipement de mesure des TC/SC Title: Measuring equipment for electrical
grandeurs électriques et électromagnétiques and electromagnetic quantities
Secretary: Mr. Bo CHEN
Secrétaire:
Also of interest to the following committees Supersedes document
Intéresse également les comités suivants Remplace le document
85/256/CD and 85/266/CC
Functions concerned
Fonctions concernées
Safety EMC Environment Quality assurance
Sécurité
CEM Environnement Assurance qualité
CE DOCUMENT EST TOUJOURS À L'ÉTUDE ET SUSCEPTIBLE DE THIS DOCUMENT IS STILL UNDER STUDY AND SUBJECT TO CHANGE. IT
MODIFICATION. IL NE PEUT SERVIR DE RÉFÉRENCE. SHOULD NOT BE USED FOR REFERENCE PURPOSES.
LES RÉCIPIENDAIRES DU PRÉSENT DOCUMENT SONT INVITÉS À RECIPIENTS OF THIS DOCUMENT ARE INVITED TO SUBMIT, WITH THEIR
PRÉSENTER, AVEC LEURS OBSERVATIONS, LA NOTIFICATION DES COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF
DROITS DE PROPRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING
CONNAISSANCE ET À FOURNIR UNE DOCUMENTATION EXPLICATIVE. DOCUMENTATION.
Titre : Title : IEC 61557-7 Ed. 2.0: Electrical safety in
low voltage distribution systems up to 1000 V
a.c. and 1500 V d.c. - Equipment for testing,
measuring or monitoring of protective measures
- Part 7: Phase sequence
Note d'introduction Introductory note
ATTENTION ATTENTION
CDV soumis en parallèle au vote (CEI) Parallel IEC CDV/CENELEC Enquiry
et à l’enquête (CENELEC)
Copyright © 2005 International Electrotechnical Commission, IEC. All rights reserved. It is
permitted to download this electronic file, to make a copy and to print out the content for the sole
purpose of preparing National Committee positions. You may not copy or "mirror" the file or
printed version of the document, or any part of it, for any other purpose without permission in
writing from IEC.
FORM CDV (IEC) 2002-08-09
---------------------- Page: 2 ----------------------
61557-7 © IEC: 2006 Ed.2.0 – 2 – 85/274/CDV
CONTENTS
Page
FOREWORD. 3
Clause
1 Scope. 5
2 Normative references. 5
3 Definitions. 5
4 Requirements. 5
5 Marking and operating instructions. 11
6 Tests. 7
Annex A – Illustrations for mechanical tests. 15
---------------------- Page: 3 ----------------------
61557-7 © IEC: 2006 Ed.2.0 – 3 – 85/274/CDV
INTERNATIONAL ELECTROTECHNICAL COMMISSION
–––––––
ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS
UP TO 1000 V a.c. AND 1500 V d.c. –
Equipment for testing, measuring or monitoring
of protective measures –
Part 7: Phase sequence
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization
comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to
promote international co-operation on all questions concerning standardization in the electrical and electronic
fields. To this end and in addition to other activities, the IEC publishes International Standards. Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt
with may participate in this preparatory work. International, governmental and non-governmental organizations
liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the
form of standards, technical reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61557-7 has been prepared by IEC technical committee 85:
Measuring equipment for electrical and electromagnetic quantities.
The text of this standard is based on the following documents:
FDIS Report on voting
85/xx/FDIS 85/xxx/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
Annex A forms an integral part of this standard.
This part of IEC 61557 shall be used in conjunction with part 1.
The committee has decided that the contents of this publication will remain unchanged until
2010. At this date, the publication will be
• reconfirmed;
---------------------- Page: 4 ----------------------
61557-7 © IEC: 2006 Ed.2.0 – 4 – 85/274/CDV
• withdrawn;
• replaced by a revised edition, or
• amended.
---------------------- Page: 5 ----------------------
61557-7 © IEC: 2006 Ed.2.0 – 5 – 85/274/CDV
ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS
UP TO 1000 V a.c. AND 1500 V d.c. –
Equipment for testing, measuring or monitoring
of protective measures –
Part 7: Phase sequence
1 Scope
This part of IEC 61557 specifies the requirements for measuring equipment applied to testing
the phase sequence in three-phase distribution systems. Indication of the phase sequence
may be mechanical, visual and/or audible.
This part of IEC 61557 does not apply to ancillary measuring equipment for other quantities,
for example voltage testers comprising an additional phase sequence indicator. It does not
apply to monitoring relays.
NOTE Phase lamps are not considered to be voltage testers.
2 Normative references
The following normative doc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.