Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop impedance (IEC 61557-3:2019)

This part of IEC 61557 specifies the requirements applicable to equipment for measuring the
loop impedance between a line conductor and protective conductor; between a line conductor
and neutral; or between two line conductors by using the voltage drop when the circuit under
test is loaded.

Elektrische Sicherheit in Niederspannungsnetzen bis AC 1 000 V und DC 1 500 V - Geräte zum Prüfen, Messen oder Überwachen von Schutzmaßnahmen - Teil 3: Schleifenwiderstand (IEC 61557-3:2019)

Sécurité électrique dans les réseaux de distribution basse tension de 1 000 V c.a. et 1 500 V c.c. - Dispositifs de contrôle, de mesure ou de surveillance de mesures de protection - Partie 3: Impédance de boucle (IEC 61557-3:2019)

IEC 61557-3:2019 est disponible sous forme de IEC 61557-3:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.

L'IEC 61557-3:2019 spécifie les exigences applicables aux appareils destinés à mesurer l'impédance de boucle entre un conducteur de ligne et le conducteur de protection, entre un conducteur de ligne et le conducteur neutre, ou entre deux conducteurs de ligne en utilisant la chute de tension lorsque le circuit en essai est chargé. L'IEC 61557-3:2019 annule et remplace la deuxième édition parue en 2007. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) ajout d'une exigence relative à la catégorie de mesure;
b) ajout de nouvelles exigences relatives aux instructions de fonctionnement;
c) alignement de la structure sur l'ensemble de la série IEC 61557.

Električna varnost v nizkonapetostnih razdelilnih sistemih za izmenične napetosti do 1 000 V in enosmerne napetosti do 1 500 V - Oprema za preskušanje, merjenje ali nadzorovanje zaščitnih ukrepov - 3. del: Impedanca zanke (IEC 61557-3:2019)

Ta del standarda IEC 61557 določa zahteve, ki se uporabljajo za opremo za merjenje impedance zanke med linijskim in zaščitnim vodnikom, med linijskim in nevtralnim vodnikom ali med dvema linijskima vodnikoma z uporabo padca napetosti ob obremenitvi preskušanega tokokroga.

General Information

Status
Published
Public Enquiry End Date
29-Apr-2018
Publication Date
08-Sep-2022
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
07-Jun-2022
Due Date
12-Aug-2022
Completion Date
09-Sep-2022

Relations

Buy Standard

Standard
SIST EN IEC 61557-3:2022
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
oSIST prEN 61557-3:2018
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61557-3:2022
01-oktober-2022
Nadomešča:
SIST EN 61557-3:2007

Električna varnost v nizkonapetostnih razdelilnih sistemih za izmenične napetosti

do 1 000 V in enosmerne napetosti do 1 500 V - Oprema za preskušanje, merjenje
ali nadzorovanje zaščitnih ukrepov - 3. del: Impedanca zanke (IEC 61557-3:2019)

Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC -

Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop

impedance (IEC 61557-3:2019)
Elektrische Sicherheit in Niederspannungsnetzen bis AC 1 000 V und DC 1 500 V -
Geräte zum Prüfen, Messen oder Überwachen von Schutzmaßnahmen - Teil 3:
Schleifenwiderstand (IEC 61557-3:2019)

Sécurité électrique dans les réseaux de distribution basse tension de 1 000 V c.a. et 1

500 V c.c. - Dispositifs de contrôle, de mesure ou de surveillance de mesures de
protection - Partie 3: Impédance de boucle (IEC 61557-3:2019)
Ta slovenski standard je istoveten z: EN IEC 61557-3:2022
ICS:
17.220.20 Merjenje električnih in Measurement of electrical
magnetnih veličin and magnetic quantities
29.080.01 Električna izolacija na Electrical insulation in
splošno general
29.240.01 Omrežja za prenos in Power transmission and
distribucijo električne energije distribution networks in
na splošno general
SIST EN IEC 61557-3:2022 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61557-3:2022
---------------------- Page: 2 ----------------------
SIST EN IEC 61557-3:2022
EUROPEAN STANDARD EN IEC 61557-3
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2022
ICS 17.220.20; 29.080.01; 29.240.01 Supersedes EN 61557-3:2007
English Version
Electrical safety in low voltage distribution systems up to 1 000 V
AC and 1 500 V DC - Equipment for testing, measuring or
monitoring of protective measures - Part 3: Loop impedance
(IEC 61557-3:2019)

Sécurité électrique dans les réseaux de distribution basse Elektrische Sicherheit in Niederspannungsnetzen bis AC

tension au plus égale à 1 000 V c.a. et 1 500 V c.c. - 1 000 V und DC 1 500 V - Geräte zum Prüfen, Messen oder

Dispositifs de contrôle, de mesure ou de surveillance de Überwachen von Schutzmaßnahmen - Teil 3:

mesures de protection - Partie 3: Impédance de boucle Schleifenwiderstand
(IEC 61557-3:2019) (IEC 61557-3:2019)

This European Standard was approved by CENELEC on 2022-04-06. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the

Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN IEC 61557-3:2022 E
---------------------- Page: 3 ----------------------
SIST EN IEC 61557-3:2022
EN IEC 61557-3:2022 (E)
European foreword

The text of document 85/687/FDIS, future edition 3 of IEC 61557-3, prepared by IEC/TC 85

"Measuring equipment for electrical and electromagnetic quantities" was submitted to the IEC-

CENELEC parallel vote and approved by CENELEC as EN IEC 61557-3:2022.
The following dates are fixed:

• latest date by which the document has to be implemented at national (dop) 2023-01-06

level by publication of an identical national standard or by endorsement

• latest date by which the national standards conflicting with the (dow) 2025-04-06

document have to be withdrawn

This document supersedes EN 61557-3:2007 and all of its amendments and corrigenda (if any).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

This document has been prepared under a Standardization Request given to CENELEC by the

European Commission and the European Free Trade Association.

Any feedback and questions on this document should be directed to the users’ national committee. A

complete listing of these bodies can be found on the CENELEC website.
Endorsement notice

The text of the International Standard IEC 61557-3:2019 was approved by CENELEC as a European

Standard without any modification.

In the official version, for Bibliography, the following note has to be added for the standard indicated:

IEC 61800-5-2 NOTE Harmonized as EN 61800-5-2
---------------------- Page: 4 ----------------------
SIST EN IEC 61557-3:2022
EN IEC 61557-3:2022 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments)

applies.

NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),

the relevant EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available

here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61010-1 2010 Safety requirements for electrical EN 61010-1 2010
equipment for measurement, control, and
laboratory use - Part 1: General
requirements
+ A1 (mod) 2016 + A1 2019
IEC 61010-2-030 2017 Safety requirements for electrical EN IEC 61010-2-030 2021
equipment for measurement, control, and
laboratory use - Part 2-030: Particular
requirements for equipment having
testing or measuring circuits
- - + A11 2021

IEC 61557-1 2019 Electrical safety in low voltage distribution EN IEC 61557-1 2021

systems up to 1 000 V AC and 1 500 V
DC - Equipment for testing, measuring or
monitoring of protective measures –
Part 1: General requirements
---------------------- Page: 5 ----------------------
SIST EN IEC 61557-3:2022
---------------------- Page: 6 ----------------------
SIST EN IEC 61557-3:2022
IEC 61557-3
Edition 3.0 2019-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and
1 500 V d.c. – Equipment for testing, measuring or monitoring of protective
measures –
Part 3: Loop impedance
Sécurité électrique dans les réseaux de distribution basse tension au plus égale
à 1 000 V c.a. et 1 500 V c.c. – Dispositifs de contrôle, de mesure ou de
surveillance de mesures de protection –
Partie 3: Impédance de boucle
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20; 29.080.01; 29.240.01 ISBN 978-2-8322-7156-8

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 61557-3:2022
– 2 – IEC 61557-3:2019 © IEC 2019
CONTENTS

FOREWORD ........................................................................................................................... 3

1 Scope .............................................................................................................................. 5

2 Normative references ....................................................................................................... 5

3 Terms and definitions....................................................................................................... 5

4 Requirements .................................................................................................................. 6

4.1 General ................................................................................................................... 6

4.2 Measurement of loop impedance ............................................................................. 6

4.3 External resistance .................................................................................................. 6

4.4 Fault voltage exceeding U ..................................................................................... 7

4.5 Overvoltage ............................................................................................................ 7

5 Marking and operating instructions ................................................................................... 7

5.1 Marking ................................................................................................................... 7

5.2 Operating instructions ............................................................................................. 7

6 Tests ............................................................................................................................... 8

6.1 General ................................................................................................................... 8

6.2 Operating uncertainty .............................................................................................. 8

6.3 External resistance ................................................................................................ 10

6.4 Fault voltage ......................................................................................................... 10

6.5 Overvoltage .......................................................................................................... 10

Bibliography .......................................................................................................................... 11

Table 1 – Calculation of operating uncertainty ......................................................................... 9

---------------------- Page: 8 ----------------------
SIST EN IEC 61557-3:2022
IEC 61557-3:2019 © IEC 2019 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS
UP TO 1 000 V AC AND 1 500 V DC –
EQUIPMENT FOR TESTING, MEASURING OR MONITORING
OF PROTECTIVE MEASURES –
Part 3: Loop impedance
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.
8) Attention is drawn
...

SLOVENSKI STANDARD
oSIST prEN 61557-3:2018
01-april-2018

(OHNWULþQDYDUQRVWYQL]NRQDSHWRVWQLKUD]GHOLOQLKVLVWHPLK]DL]PHQLþQHQDSHWRVWL

GRN9LQHQRVPHUQHQDSHWRVWLGRN92SUHPD]DSUHVNXãDQMHPHUMHQMHDOL
QDG]RURYDQMH]DãþLWQLKXNUHSRYGHO,PSHGDQFD]DQNH

Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. -

Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop

impedance
Elektrische Sicherheit in Niederspannungsnetzen bis AC 1 000 V und DC 1 500 V -
Geräte zum Prüfen, Messen oder Überwachen von Schutzmaßnahmen - Teil 3:
Schleifenwiderstand

Sécurité électrique dans les réseaux de distribution basse tension de 1 000 V c.a. et 1

500 V c.c. - Dispositifs de contrôle, de mesure ou de surveillance de mesures de
protection - Partie 3: Impédance de boucle
Ta slovenski standard je istoveten z: prEN 61557-3:2018
ICS:
17.220.20 0HUMHQMHHOHNWULþQLKLQ Measurement of electrical
PDJQHWQLKYHOLþLQ and magnetic quantities
29.080.01 (OHNWULþQDL]RODFLMDQD Electrical insulation in
VSORãQR general
29.240.01 2PUHåMD]DSUHQRVLQ Power transmission and
GLVWULEXFLMRHOHNWULþQHHQHUJLMH distribution networks in
QDVSORãQR general
oSIST prEN 61557-3:2018 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 61557-3:2018
---------------------- Page: 2 ----------------------
oSIST prEN 61557-3:2018
85/631/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61557-3 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2018-02-09 2018-05-04
SUPERSEDES DOCUMENTS:
85/609/CD,85/623/CC
IEC TC 85 : MEASURING EQUIPMENT FOR ELECTRICAL AND ELECTROMAGNETIC QUANTITIES
SECRETARIAT: SECRETARY:
China Mr Bo Chen
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
TC 44,TC 64,TC 66
Other TC/SCs are requested to indicate their interest, if any,
in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY

SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING

Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for
Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.

This document is still under study and subject to change. It should not be used for reference purposes.

Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they

are aware and to provide supporting documentation.
TITLE:

Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for

testing, measuring or monitoring of protective measures - Part 3: Loop impedance
PROPOSED STABILITY DATE: 2025
NOTE FROM TC/SC OFFICERS:

Copyright © 2017 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this

electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.

You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without

permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN 61557-3:2018
- 2 - 85/631/CDV
2 CONTENTS

4 FOREWORD ...................................................................................................................... - 3 -

5 1 Scope ......................................................................................................................... - 5 -

6 2 Normative references .................................................................................................. - 5 -

7 3 Terms and definitions .................................................................................................. - 5 -

8 4 Requirements ............................................................................................................. - 6 -

9 4.1 General .............................................................................................................. - 6 -

10 4.2 Measurement of loop impedance ........................................................................ - 6 -

11 4.3 External resistance ............................................................................................. - 6 -

12 4.4 Fault voltage exceeding U ................................................................................ - 6 -

13 4.5 Overvoltage ........................................................................................................ - 6 -

14 5 Marking and operating instructions .............................................................................. - 6 -

15 5.1 Marking .............................................................................................................. - 6 -

16 5.2 Operating instructions ........................................................................................ - 7 -

17 6 Tests .......................................................................................................................... - 7 -

18 6.1 General .............................................................................................................. - 7 -

19 6.2 Operating uncertainty ......................................................................................... - 7 -

20 6.3 External resistance ............................................................................................. - 9 -

21 6.4 Fault voltage ...................................................................................................... - 9 -

22 6.5 Overvoltage ........................................................................................................ - 9 -

23 Bibliography ..................................................................................................................... - 10 -

25 Table 1 – Calculation of operating uncertainty .................................................................... - 8 -

---------------------- Page: 4 ----------------------
oSIST prEN 61557-3:2018
- 3 - 85/631/CDV
27 INTERNATIONAL ELECTROTECHNICAL COMMISSION
28 ____________
30 ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS
31 UP TO 1 000 V AC AND 1 500 V DC –
32 EQUIPMENT FOR TESTING, MEASURING OR MONITORING
33 OF PROTECTIVE MEASURES –
35 Part 3: Loop impedance
37 FOREWORD

38 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

39 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

40 international co-operation on all questions concerning standardization in the electrical and electronic fields. To

41 this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

42 Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

43 Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

44 in the subject dealt with may participate in this preparatory work. International, governmental and non-

45 governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

46 with the International Organization for Standardization (ISO) in accordance with conditions determined by

47 agreement between the two organizations.

48 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

49 consensus of opinion on the relevant subjects since each technical committee has representation from all

50 interested IEC National Committees.

51 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

52 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

53 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

54 misinterpretation by any end user.

55 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

56 transparently to the maximum extent possible in their national and regional publications. Any divergence

57 between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

58 the latter.

59 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

60 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

61 services carried out by independent certification bodies.

62 6) All users should ensure that they have the latest edition of this publication.

63 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

64 members of its technical committees and IEC National Committees for any personal injury, property damage or

65 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

66 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

67 Publications.

68 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

69 indispensable for the correct application of this publication.

70 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

71 patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

72 International Standard IEC 61557-3 has been prepared by IEC technical committee TC85:

73 Measuring equipment for electrical and electromagnetic quantities

74 This third edition cancels and replaces the second edition published in 2009. This edition

75 constitutes a technical revision.

76 This edition includes the following significant technical changes with respect to the previous

77 edition:
78 a) requirement for measurement category added
79 b) new requirements for operating instructions added
80 c) Alignment of the structure to the whole series IEC61557
82 The text of this standard is based on the following documents:
---------------------- Page: 5 ----------------------
oSIST prEN 61557-3:2018
- 4 - 85/631/CDV
FDIS Report on voting
XX/XX/FDIS XX/XX/RVD

84 Full information on the voting for the approval of this standard can be found in the report on

85 voting indicated in the above table.

86 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

87 This part of IEC 61557 shall be used in conjunction with Part 1.

88 A list of all parts in the IEC 61557 series, published under the general title Electrical safety in

89 low voltage distribution systems up to 1 000 V AC and 1 500 V DC – Equipment for testing,

90 measuring or monitoring of protective measure,’ can be found on the IEC website.

91 The committee has decided that the contents of this publication will remain unchanged until

92 the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data

93 related to the specific publication. At this date, the publication will be
94 • reconfirmed,
95 • withdrawn,
96 • replaced by a revised edition, or
97 • amended.

99 The National Committees are requested to note that for this publication the stability date

100 is 2025

101 THIS TEXT IS INCLUDED FOR THE INFORMATION OF THE NATIONAL COMMITTEES AND WILL BE

102 DELETED AT THE PUBLICATION STAGE.
---------------------- Page: 6 ----------------------
oSIST prEN 61557-3
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.