SIST EN ISO 1167-3:2008
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007)
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007)
This part of ISO 1167 specifies the procedure for the preparation of components, i.e. fittings and valve bodies, for the determination of their resistance to internal hydrostatic pressure according to ISO 1167-1.
Rohre, Formstücke und Bauteilkombinationen aus thermoplastischen Kunststoffen für den Transport von Flüssigkeiten - Bestimmung der Widerstandsfähigkeit gegen inneren Überdruck - Teil 3: Vorbereitung der Rohrleitungsteile (ISO 1167-3:2007)
Dieser Teil der Internationalen Norm ISO 1167 legt das Verfahren für die Vorbereitung der Rohrleitungsteile, d. h. Formstücke, Armaturenkörper, für die Bestimmung der Widerstandsfähigkeit gegen Innendruck nach ISO 1167-1 fest.
ANMERKUNG Formstücke aus Polyoefin für Stumpfschweißen, Heizwendelschweißen und Muffenschweißen werden stets als Bauteilkombinationen geprüft und in ISO 1167-4 behandelt. Rohr-Probekörper werden in ISO 1167-2 behandelt.
Tubes, raccords et assemblages en matieres thermoplastiques pour le transport des fluides - Détermination de la résistance a la pression interne - Partie 3: Préparation des composants (ISO 1167-3:2007)
L'ISO 1167-3:2007 spécifie le mode opératoire pour la préparation des composants, à savoir les raccords et les corps de robinet, en vue de déterminer la résistance à la pression hydrostatique interne selon l'ISO 1167-1.
Plastomerne cevi, fitingi in spoji za transport tekočin in plinov - Preskusna metoda za ugotavljanje odpornosti proti notranjemu tlaku - 3. del: Priprava sestavnih delov (ISO 1167-3:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 1167-3:2008
01-junij-2008
1DGRPHãþD
SIST EN 921:1997
3ODVWRPHUQHFHYLILWLQJLLQVSRML]DWUDQVSRUWWHNRþLQLQSOLQRY3UHVNXVQDPHWRGD
]DXJRWDYOMDQMHRGSRUQRVWLSURWLQRWUDQMHPXWODNXGHO 3ULSUDYDVHVWDYQLKGHORY
,62
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids -
Determination of the resistance to internal pressure - Part 3: Preparation of components
(ISO 1167-3:2007)
Rohre, Formstücke und Bauteilkombinationen aus thermoplastischen Kunststoffen für
den Transport von Flüssigkeiten - Bestimmung der Widerstandsfähigkeit gegen inneren
Überdruck - Teil 3: Vorbereitung der Rohrleitungsteile (ISO 1167-3:2007)
Tubes, raccords et assemblages en matieres thermoplastiques pour le transport des
fluides - Détermination de la résistance a la pression interne - Partie 3: Préparation des
composants (ISO 1167-3:2007)
Ta slovenski standard je istoveten z: EN ISO 1167-3:2007
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
SIST EN ISO 1167-3:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 1167-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2007
ICS 23.040.45; 23.040.20 Supersedes EN 921:1994
English Version
Thermoplastics pipes, fittings and assemblies for the
conveyance of fluids - Determination of the resistance to internal
pressure - Part 3: Preparation of components (ISO 1167-3:2007)
Tubes, raccords et assemblages en matières Rohre, Formstücke und Bauteilkombinationen aus
thermoplastiques pour le transport des fluides - thermoplastischen Kunststoffen für den Transport von
Détermination de la résistance à la pression interne - Partie Flüssigkeiten - Bestimmung der Widerstandsfähigkeit
3: Préparation des composants (ISO 1167-3:2007) gegen inneren Überdruck - Teil 3: Vorbereitung der
Rohrleitungsteile (ISO 1167-3:2007)
This European Standard was approved by CEN on 2 October 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1167-3:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 1167-3:2007 (E)
Contents Page
Foreword.3
2
---------------------- Page: 3 ----------------------
EN ISO 1167-3:2007 (E)
Foreword
This document (EN ISO 1167-3:2007) has been prepared by Technical Committee ISO/TC 138 "Plastics
pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the
latest by May 2008.
This document supersedes EN 921:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 1167-3:2007 has been approved by CEN as a EN ISO 1167-3:2007 without any modification.
3
---------------------- Page: 4 ----------------------
INTERNATIONAL ISO
STANDARD 1167-3
First edition
2007-11-01
Thermoplastics pipes, fittings and
assemblies for the conveyance of
fluids — Determination of the resistance
to internal pressure —
Part 3:
Preparation of components
Tubes, raccords et assemblages en matières thermoplastiques pour le
transport des fluides — Détermination de la résistance à la pression
interne —
Partie 3: Préparation des composants
Reference number
ISO 1167-3:2007(E)
©
ISO 2007
---------------------- Page: 5 ----------------------
ISO 1167-3:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 6 ----------------------
ISO 1167-3:2007(E)
Contents Page
Foreword. iv
1 Scope .1
2 Normative references .1
3 Principle.1
4 Pressure-tight devices .2
4.1 General.2
4.2 Components with plain sockets.2
4.3 Components with socket and gasket .5
4.4 Closing devices for valve bodies.6
5 Test pieces .8
5.1 Sampling.8
5.2 Preparation of test pieces.9
6 Test report .9
© ISO 2007 – All rights reserved iii
---------------------- Page: 7 ----------------------
ISO 1167-3:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has
been established has the right to be represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1167-3 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and
their accessories — Test methods and basic specifications.
This first edition of ISO 1167-3, together with ISO 1167-2, cancels and replaces ISO 12092:2000, of which it
constitutes a technical revision.
ISO 1167-3 consists of the following parts, under the general title Thermoplastics pipes, fittings and
assemblies for the conveyance of fluids — Determination of the resistance to internal pressure:
⎯ Part 1: General method
⎯ Part 2: Preparation of pipe test pieces
⎯ Part 3: Preparation of components
⎯ Part 4: Preparation of assemblies
iv © ISO 2007 – All rights reserved
---------------------- Page: 8 ----------------------
INTERNATIONAL STANDARD ISO 1167-3:2007(E)
Thermoplastics pipes, fittings and assemblies for the
conveyance of fluids — Determination of the resistance to
internal pressure —
Part 3:
Preparation of components
1 Scope
This part of ISO 1167 specifies the procedure for the preparation of components, i.e. fittings and valve bodies,
for the determination of their resistance to internal hydrostatic pressure according to ISO 1167-1.
NOTE Polyolefin fittings for butt fusion, electrofusion and socket fusion are usually tested as an assem
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.