SIST EN ISO 4029:2004
(Main)Hexagon socket set screws with cup point (ISO 4029:2003)
Hexagon socket set screws with cup point (ISO 4029:2003)
ISO 4029:2003 specifies the characteristics of hexagon socket set screws with cup point and threads from M1,6 up to and including M24 and of product grade A.
Gewindestifte mit Innensechskant mit Ringschneide (ISO 4029:2003)
Diese Internationale Norm legt die Eigenschaften von Gewindestiften mit Innensechskant mit Ringschneide mit Gewinde von M1,6 bis einschließlich M24 in Produktklasse A fest.
Werden in besonderen Fällen andere Festlegungen als die in der vorliegenden Internationalen Norm benötigt, so sollten diese den bestehenden Internationalen Normen entnommen werden, z. B. ISO 261, ISO 898-5, ISO 965-2, ISO 3506-3 und ISO 4759-1.
Vis sans tete a six pans creux, a bout cuvette (ISO 4029:2003)
L'ISO 4029:2003 spécifie les caractéristiques des vis sans tête à six pans creux, à bout cuvette, de filetage M1,6 à M24 inclus et de grade A.
Navojni zatiči z notranjim šestkotnikom in obročastim rezilom (ISO 4029:2003)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gewindestifte mit Innensechskant mit Ringschneide (ISO 4029:2003)Vis sans tete a six pans creux, a bout cuvette (ISO 4029:2003)Hexagon socket set screws with cup point (ISO 4029:2003)21.060.10Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN ISO 4029:2003SIST EN ISO 4029:2004en01-junij-2004SIST EN ISO 4029:2004SLOVENSKI
STANDARD
SIST EN ISO 4029:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 4029December 2003ICS 21.060.10English versionHexagon socket set screws with cup point (ISO 4029:2003)Vis sans tête à six pans creux, à bout cuvette (ISO4029:2003)Gewindestifte mit Innensechskant mit Ringschneide (ISO4029:2003)This European Standard was approved by CEN on 4 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 4029:2003 ESIST EN ISO 4029:2004
EN ISO 4029:2003 (E)2CORRECTED
2004-03-03ForewordThis document (EN ISO 4029:2003) has been prepared by Technical Committee ISO/TC 2"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication ofan identical text or by endorsement, at the latest by June 2004, and conflicting nationalstandards shall be withdrawn at the latest by June 2004.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland andthe United Kingdom.Endorsement noticeThe text of ISO 4029:2003 has been approved by CEN as EN ISO 4029:2003 without anymodifications.NOTE
Normative references to International Standards are listed in Annex ZA (normative).SIST EN ISO 4029:2004
EN ISO 4029:2003 (E)3Annex ZA(normative)Normative references to international publicationswith their relevant European publicationsThis European Standard incorporates by dated or undated reference, provisions from otherpublications. These normative references are cited at the appropriate places in the text and thepublications are listed hereafter. For dated references, subsequent amendments to or revisions ofany of these publications apply to this European Standard only when incorporated in it byamendment or revision. For undated references the latest edition of the publication referred toapplies (including amendments).NOTE Where an International Publication has been modified by common modifications, indicatedby (mod.), the relevant EN/HD applies.PublicationYearTitleENYearISO 2251983Fasteners - Bolts, screws, studs andnuts - Symbols and designations ofdimensionsEN 202251991ISO 898-51998Mechanical properties of fastenersmade of carbon steel and alloy steel- Part 5: Set screws and similarthreaded fasteners not under tensilestressesEN ISO 898-51998ISO 32692000Fasteners - Acceptance inspectionEN ISO 32692000ISO 3506-31997Mechanical properties of corrosion-resistant stainless-steel fasteners -Part 3: Set screws and similarfasteners not under tensile stressEN ISO 3506-31997ISO 40421999Fasteners - Electroplated coatingsEN ISO 40421999ISO 4759-12000Tolerances for fasteners - Part 1:Bolts, screws, studs and
nuts -Product grades A, B and CEN ISO 4759-12000ISO 6157-11988Fasteners - Surface discontinuities -Part 1: Bolts, screws and studs forgeneral requirementsEN 26157-11991ISO 88391986Mechanical properties of fasteners -Bolts, screws, studs and nuts madeof non-ferrous metalsEN 288391991ISO 106832000Fasteners - Non-electrolyticallyapplied zinc flake coatingsEN ISO 106832000ISO 234292004Gauging of hexagon socketsEN ISO 234292004SIST EN ISO 4029:2004
SIST EN ISO 4029:2004
INTERNATIONALSTANDARDISO4029Third edition2003-12-01Reference numberISO4029:2003(E)© ISO2003Hexagon socket set screws with cup pointVis sans tête à six pans creux, à bout cuvette
SIST EN ISO 4029:2004
ISO4029:2003(E)ii© ISO2003–All rights reservedPDF disclaimerThis PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shallnot be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. Indownloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariataccepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creationparameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In theunlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.©ISO2003All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below orISO's member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel.+ 41 22 749 01 11Fax+ 41 22 749 09 47E-mailcopyright@iso.orgWebwww.iso.orgPublished in SwitzerlandSIST EN ISO 4029:2004
ISO4029:2003(E)© ISO2003–All rights reservediiiForewordISO (the International Organization for Standardization) is a worldwide fede
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.