Electronic fee collection - Evaluation of equipment for conformity to ISO/TS 17575-3 - Part 1: Test suite structure and test purposes (ISO/TS 16410-1:2011)

The Technical Specification will define the conformity evaluation tests suite for equipment to the EFC standard on "Application interface definition for autonomous systems - Context data" (i.e. CEN ISO/TS 17575 - Part 3).
This part will contain the test suite structure and test purposes ("the human readable part"), and use the methodology for defining conformity tests as defined in the TTCN suite of standards (i.e. ISO/IEC 9646). It will cover tests for the Back End equipment and for the Front End (as either a proxy or a smart client OBE) equipment.
The approach and structure will be analogous to "Conformity evaluation of on-board and road equipment to EN 15509" (prEN 15876-1, cf CEN Enquiry version).
The Front End and Back End equipment will most likely be subject to additional testing of physical, environmental endurance, quality assurance and control at manufacturing, charge point integration, as part of factory, site and system acceptance testing. The definition of these tests is outside the scope of this standard.
Conformity evaluation tests for non-functional requirements like sensor accuracy, performance levels and computing power are outside the scope of this standard. They should be covered by the conformity evaluation to the appropriate profile standard.

Elektronische Gebührenerfassung - Konformitätsevaluierung von Equipment zur CEN ISO/TS 17575-3 - Teil 1: Struktur der Testfolge und Testabsichten (ISO/TS 16410-1:2011)

Perception du télépéage - Évaluation de la conformité de l'équipement à l'ISO/TS 17575-3 - Partie 1: Structure de la suite d'essais et objectifs des essais (ISO/TS 16410-1:2011)

Elektronsko pobiranje pristojbin - Ugotavljanje skladnosti opreme s tehnično specifikacijo ISO/TS 17575-3 - 1. del: Zgradba preskuševalnega niza in namen preskušanja (ISO/TS 16410-1:2011)

Ta tehnična specifikacija bo določala zbirko preskusov za ocenjevanje skladnosti opreme z EFC standardom »Definicija aplikacijskega vmesnika za avtonomne sisteme – Okvirni podatki« (tj. CEN ISO/TS 17575 – 3. del).
Ta del bo vseboval strukturo zbirke preskusov in namene preskusov (»človeku berljiv del«) in uporabo metodologije za določanje preskusov skladnosti, kot je določeno v zbirki standardov TTCN (tj. ISO/IEC 9646). Zajemal bo preskuse za opremo zadnjega dela in opreme prednjega dela (ali kot proksi ali kot pameten klient OBE).
Pristop in struktura bosta analogna z »ocenjevanjem skladnosti za vgrajeno in cestno opremo z EN 15509« (prEN 15876-1, cf verzija poizvedbe CEN).
Oprema za prednji in zadnji del bo po vsej verjetnosti predmet dodatnega preskušanja fizične in okoljske vzdržljivosti, zagotavljanja kakovosti in nadzora pri proizvodnji, integracije plačilne točke, kot del tovarne, lokacije in preskušanja sprejemljivosti sistema. Definicija teh preskusov je zunaj okvira tega standarda.
Preskusi za ocenjevanje skladnosti z nedelovne zahteve, kot so natančnost senzorjev, stopnje delovanja in moči računanja, so zunaj področja uporabe tega standarda. Zajeti bi morali biti z ocenjevanjem skladnosti ustreznega profila standarda.

General Information

Status
Withdrawn
Publication Date
08-Nov-2011
Withdrawal Date
07-Jan-2018
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
22-Dec-2017
Due Date
14-Jan-2018
Completion Date
08-Jan-2018

RELATIONS

Buy Standard

Technical specification
SIST-TS CEN ISO/TS 16410-1:2011
English language
155 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST-TS CEN ISO/TS 16410-1:2011
01-december-2011
(OHNWURQVNRSRELUDQMHSULVWRMELQ8JRWDYOMDQMHVNODGQRVWLRSUHPHVWHKQLþQR
VSHFLILNDFLMR,6276GHO=JUDGEDSUHVNXãHYDOQHJDQL]DLQQDPHQ
SUHVNXãDQMD ,6276

Electronic fee collection - Evaluation of equipment for conformity to ISO/TS 17575-3 -

Part 1: Test suite structure and test purposes (ISO/TS 16410-1:2011)
Elektronische Gebührenerfassung - Konformitätsevaluierung von Equipment zur CEN
ISO/TS 17575-3 - Teil 1: Struktur der Testfolge und Testabsichten (ISO/TS 16410-
1:2011)

Perception du télépéage - Évaluation de la conformité de l'équipement à l'ISO/TS 17575-

3 - Partie 1: Structure de la suite d'essais et objectifs des essais (ISO/TS 16410-1:2011)

Ta slovenski standard je istoveten z: CEN ISO/TS 16410-1:2011
ICS:
03.220.20 Cestni transport Road transport
35.240.60 Uporabniške rešitve IT v IT applications in transport
transportu in trgovini and trade
SIST-TS CEN ISO/TS 16410-1:2011 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
---------------------- Page: 2 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
TECHNICAL SPECIFICATION
CEN ISO/TS 16410-1
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
October 2011
ICS 35.240.60; 03.220.20
English Version
Electronic fee collection - Evaluation of equipment for conformity
to ISO/TS 17575-3 - Part 1: Test suite structure and test
purposes (ISO/TS 16410-1:2011)

Perception du télépéage - Évaluation de la conformité de Elektronische Gebührenerfassung -

l'équipement à l'ISO/TS 17575-3 - Partie 1: Structure de la Konformitätsevaluierung von Equipment zur CEN ISO/TS

suite d'essais et objectifs des essais (ISO/TS 16410- 17575-3 - Teil 1: Struktur der Testfolge und Testabsichten

1:2011) (ISO/TS 16410-1:2011)

This Technical Specification (CEN/TS) was approved by CEN on 15 August 2011 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their

comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available

promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)

until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 16410-1:2011: E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
CEN ISO/TS 16410-1:2011 (E)
Contents Page

Foreword ..............................................................................................................................................................3

---------------------- Page: 4 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
CEN ISO/TS 16410-1:2011 (E)
Foreword

This document (CEN ISO/TS 16410-1:2011) has been prepared by Technical Committee CEN/TC 278 “Road

transport and traffic telematics”, the secretariat of which is held by NEN, in collaboration with Technical

Committee ISO/TC 204 “Intelligent transport systems”.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following

countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,

Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

Spain, Sweden, Switzerland and the United Kingdom.
---------------------- Page: 5 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
---------------------- Page: 6 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
TECHNICAL ISO/TS
SPECIFICATION 16410-1
First edition
2011-10-15
Electronic fee collection — Evaluation
of equipment for conformity to
ISO/TS 17575-3 —
Part 1:
Test suite structure and test purposes
Perception du télépéage — Évaluation de la conformité de l'équipement
à l'ISO/TS 17575-3 —
Partie 1: Structure de la suite d'essais et objectifs des essais
Reference number
ISO/TS 16410-1:2011(E)
ISO 2011
---------------------- Page: 7 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
Contents Page

Foreword ............................................................................................................................................................ iv

Introduction ......................................................................................................................................................... v

1  Scope ...................................................................................................................................................... 1

2  Normative references ............................................................................................................................ 2

3  Terms and definitions ........................................................................................................................... 2

4  Abbreviated terms ................................................................................................................................. 4

5  Test Suite Structure (TSS) .................................................................................................................... 4

5.1  Structure ................................................................................................................................................. 4

5.2  Reference to conformance test specifications .................................................................................. 6

5.3  Test Purposes (TP) ................................................................................................................................ 6

5.4  Conformance test report ....................................................................................................................... 7

Annex A (normative) Test Purposes (TP) for Front End ................................................................................. 8

Annex B (normative) Test purposes (TP) for Back End ................................................................................ 92

Annex C (normative) Data Structures ........................................................................................................... 124

Annex D (normative) PCTR for Front End .................................................................................................... 135

Annex E (normative) PCTR for Back End ..................................................................................................... 141

Bibliography .................................................................................................................................................... 147

© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

In other circumstances, particularly when there is an urgent market requirement for such documents, a

technical committee may decide to publish other types of document:

— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in

an ISO working group and is accepted for publication if it is approved by more than 50 % of the members

of the parent committee casting a vote;

— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical

committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting

a vote.

An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a

further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is

confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an

International Standard or be withdrawn.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO/TS 16410-1 was prepared by Technical Committee ISO/TC 204, Intelligent transport systems, in

collaboration with Technical Committee CEN/TC 278, Road Transport and Traffic Telematics.

ISO/TS 16410 consists of the following parts, under the general title Electronic fee collection — Evaluation of

equipment for conformity to ISO/TS 17575-3:
— Part 1: Test suite structure and test purposes
— Part 2: Abstract test suites
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
Introduction

This part of ISO 16410 is part of a set of standards that supports interoperability of autonomous EFC-systems,

which includes ISO/TS 17575 parts 1 to 4 that define the EFC context data, their charge reports and their use

of communication infrastructure.

Within the suite of EFC standards this conformance evaluation procedure defines the process and tests for

conformity evaluation of Front End and Back End that comply with the requirements in ISO/TS 17575-3.

This part of ISO 16410 is intended to
 assess Front End and Back End capabilities,
 assess Front End and Back End behaviour,

 serve as a guide for Front End and Back End conformance evaluation and type approval,

 achieve comparability between the results of the corresponding tests applied in different places at

different times, and
 facilitate communications between parties.
This part of ISO 16410 is based on
 ISO/TS 17575-3, and
 the ISO 9646 family of standards on conformance test methodology.
© ISO 2011 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
---------------------- Page: 12 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
TECHNICAL SPECIFICATION ISO/TS 16410-1:2011(E)
Electronic fee collection — Evaluation of equipment for
conformity to ISO/TS 17575-3 —
Part 1:
Test suite structure and test purposes
1 Scope

This part of ISO/TS 16410 specifies the test suite structure (TSS) and test purposes (TP) to evaluate the

conformity of Front End and Back End to ISO/TS 17575-3.

The objective of this part of ISO/TS 16410 is to provide a basis for conformance tests for the Front End and

the Back End in Electronic Fee Collection (EFC) based on autonomous on-board equipment (OBE) to enable

interoperability between different equipment supplied by different manufacturers.

Autonomous OBE operates without relying on dedicated road-side infrastructure by employing wide-area

technologies such as Global Navigation Satellite Systems (GNSS) and Cellular Communications Networks

(CN). These EFC systems are referred to by a variety of names. Besides the terms autonomous systems and

GNSS/CN systems, also the terms GPS/GSM systems and wide-area charging systems are in use.

Autonomous systems use satellite positioning, often combined with additional sensor technologies such as

gyroscopes, odometers, and accelerometers, to localise the vehicle and to find its position on a map

containing the charged geographic objects, such as charged roads or charged areas. From the charged

objects, the vehicle characteristics, the time of day and other data that are relevant for describing road use,

the tariff and ultimately the road usage fee is determined.

For more information regarding autonomous systems, please refer to ISO/TS 17575-3.

Testing of the following behaviours and functionalities is outside of the scope of this part of ISO/TS 16410:

 dynamic behaviour, i.e. sequence of messages and triggering events that must be exchanged/happen to

fulfil certain charging scenarios;
 profiles and business logic built on top of particular pricing schemas;
 authentication, as its handling is not described in ISO/TS 17575-3;

 Front End behaviour with respect to optional data elements in ChargeReportConfiguration, as handling of

configurations requesting presence/absence of parent data element, and absence/presence of child data

element is not specified in ISO/TS 17575-3.

As ISO/TS 17575-3 does not specify any invalid behaviour of Front End and Back End, BI test purposes are

not applicable for any test purpose group.
© ISO 2011 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.

ISO/IEC 9646-6, Information technology — Open Systems Interconnection — Conformance testing

methodology and framework — Part 6: Protocol profile test specification

ISO/TS 17575-1, Electronic fee collection — Application interface definition for autonomous systems —

Part 1: Charging

ISO/TS 17575-3, Electronic fee collection — Application interface definition for autonomous systems —

Part 3: Context data
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
area pricing
charging process based on road usage occurring within a given area
[ISO/TS 17575-1:2010, definition 3.1]
3.2
attribute

application information formed by one or by a sequence of data elements, and that is managed by different

actions used for implementation of a transaction
[ISO 14906:2011, definition 3.3]
3.3
authenticator

data appended to, or a cryptographic transformation of, a data unit that allows a recipient of the data unit to

prove the source and/or the integrity of the data unit and protect against forgery

[ISO 14906:2011, definition 3.4]
3.4
Back End

generic name for the computing and communication facilities of the Service Provider and the Toll Charger

exchanging data with the Front End
NOTE 1 Adapted from ISO/TS 17575-1.

NOTE 2 According to the architecture defined in ISO 17573, it is assumed in this part of ISO/TS 16410 that the Front

End in general communicates with the Back End typically controlled and operated by the Service Provider.

3.5
charge object

any object that is part of the toll context description, including toll objects but also used for parking fees, etc.

NOTE Adapted from ISO/TS 17575-1.
3.6
charge report

data structure transmitted from the Front End to the Back End to report road usage data and supplementary

related information
[ISO/TS 17575-1:2010, definition 3.5]
2 © ISO 2011 – All rights reserved
---------------------- Page: 14 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
3.7
contract

expression of an agreement between two or more parties concerning the use of the road infrastructure

[ISO 14906:2011, definition 3.7]
3.8
cordon
border line of an area
[ISO/TS 17575-1:2010, definition 3.8]
3.9
cordon pricing
charging process based on registering passages of a cordon
[ISO/TS 17575-1:2010, definition 3.9]
3.10
data element
datum, which might itself consist of lower level data elements
[ISO/TS 17575-1:2010, definition 3.10]
3.11
Front End

part(s) of the toll system where road usage data for an individual road user are collected, processed and

delivered to the Back End
NOTE The Front End comprises the on-board equipment and an optional proxy.
[ISO/TS 17575-1:2010, definition 3.13]
3.12
service provider

operator that accepts the user's payment means and in return provides a road-use service to the user

NOTE Taken from ISO 14906:2004.
3.13
tester

combination of equipment and processes which is able to perform conformance tests according to this part of

ISO/TS 16410
NOTE Adapted from ISO/TS 14907-2.
3.14
toll charger
legal entity charging a toll for vehicles in a toll domain
[ISO/TS 17574:2009, definition 3.27]
3.15
toll context
logical view of a toll scheme as defined by attributes and functions
[ISO/TS 17575-1:2010, definition 3.22]
3.16
toll regime

set of rules, including enforcement rules, governing the collection of toll in a toll

[ISO/TS 17575-1:2010, definition 3.25]
© ISO 2011 – All rights reserved 3
---------------------- Page: 15 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
4 Abbreviated terms

For the purposes of this document, the following abbreviated terms apply, unless otherwise specified.

ADU Application data unit (ISO/TS 17575-1)
ASN.1 Abstract Syntax Notation One (ISO/IEC 8824-1:2002)
ATS Abstract Test Suite
BI Invalid Behaviour
BV Valid Behaviour
CCC Compliance Check Communication (ISO/TS 12813)
CN Cellular network (ISO/TS 17575-1)
DUT Device Under Test
EFC Electronic Fee Collection (ISO 17573)
GNSS Global Navigation Satellite Systems (ISO/TS 17575-1)
HMI Human Machine Interface (ISO/TS 17575-1)
ID Identifier
OBE On-board Equipment (ISO/TS 17575-1)
PCTR Proforma Conformance Test Report
PICS Protocol Implementation Conformance Statements
TP Test Purposes
TSS Test Suite Structure
VAT Value Added Tax (ISO/TS 17575-1)
5 Test Suite Structure (TSS)
5.1 Structure
Table 1 — Test Suite Structures shows the Test Suite Structure (TSS).
Table 1 — Test Suite Structures
Group Type of DUT Behaviour
Procedural Back End Valid Behaviour
Invalid Behaviour not
applicable
ADU Header Back End Valid Behaviour
Invalid Behaviour not
applicable
4 © ISO 2011 – All rights reserved
---------------------- Page: 16 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
ADU Body – Attribute Back End Valid Behaviour
general
Invalid Behaviour not
applicable
Toll Context Overview Back End Valid Behaviour
Invalid Behaviour not
applicable
Tariff Table Back End Valid Behaviour
Invalid Behaviour not
applicable
Tariff Class Definition Back End Valid Behaviour
Invalid Behaviour not
applicable
Local Vehicle Class Back End Valid Behaviour
Definition
Invalid Behaviour not
applicable
Time Class Definition Back End Valid Behaviour
Invalid Behaviour not
applicable
User Class Definition Back End Valid Behaviour
Invalid Behaviour not
applicable
Toll Context Layout Back End Valid Behaviour
Invalid Behaviour not
applicable
Toll Context Layout for Back End Valid Behaviour
Section Pricing
Invalid Behaviour not
applicable
Toll Context Layout for Area Back End Valid Behaviour
Pricing
Invalid Behaviour not
applicable
Toll Context Layout for Back End Valid Behaviour
Cordon Pricing
Invalid Behaviour not
applicable
Context Handling Front End Valid Behaviour
Invalid Behaviour not
applicable
Charge Report Front End Valid Behaviour
Invalid Behaviour not
applicable

Front End related Test Purposes uses Charge Report message for validation which is specified in

ISO/TS 17575-1. As a precondition to run those test purposes the compliance to ISO/TS 17575-1 shall be

validated.
© ISO 2011 – All rights reserved 5
---------------------- Page: 17 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
5.2 Reference to conformance test specifications

This part of ISO/TS 16410 takes into account already defined test purposes for conformance to the base

standards by referencing them, so that

a) for test purposes that are identical to those defined in this specification or the base standards

conformance test cases direct reference is reported; for reader’s convenience, the title or a verbal

description of the referenced test purpose is given, together with the reference,

b) for test purposes that are derived from those defined in the base standards conformance test cases, a

direct reference is reported, plus an indication on how the referred test purpose has to be modified for the

profile conformance testing,

c) for test purposes that are specific to ISO/TS 17575-3, a complete description is given, and

d) an indication on whether a test purpose is identical, derived, or specific is given in each test purpose.

5.3 Test Purposes (TP)
5.3.1 TP definition conventions

The TPs are defined following the rules shown in Table 2 — TP Definition Rules below. All test purposes are

defined in Annex A and Annex B, including the special notation and symbol conventions that shall be used.

The data structures that shall be used are specified in Annex C and defined in ISO/TS 17575-1 and

ISO/TS 17575-3.
Table 2 — TP Definition Rules
TP ID according to the TP naming Title
conventions
Reference
TP origin
Initial condition
Stimulus and expected behaviour
TP ID The TP ID is a unique identifier. It shall be specified according to
the TP naming conventions defined in the sub-clause below.
Title Short description of Test Purpose objective.
Reference The reference should contain the references of the subject to be
validated by the actual TP (specification reference, clause,
paragraph), or the reference to the standard document defining
the TP.
TP origin Indicates if the TP is identical to a TP defined in another test
standard, derived from a TP defined in another test standard, or
specific for this standard profile.

Initial condition The condition defines in which initial state the DUT has to be to

apply the actual TP.

Stimulus and expected Definition of the events the tester performs, and the events that are

behaviour expected from the
DUT to conform to the base specification.
6 © ISO 2011 – All rights reserved
---------------------- Page: 18 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
5.3.2 TP naming conventions

Each TP is given a unique identification. This unique identification is built up to contain the following string of

information:
TP///-
TP : to indicate that it is a Test Purpose;
: which group TP belongs to;
: type of DUT (i.e. FE or BE);

X : type of testing (i.e. Valid Behaviour tests – BV, or Invalid Behaviour tests – BI)

: sequential TP number (01-99)
The naming conventions are as described in Table 3.
Table 3 — TP naming convention
Identifier:
TP///-

applicable for BE PRO Procedural
applicable for BE ADUH ADU Header
applicable for BE ADUB ADU Body – Attribute general
applicable for BE ATTR-11 Toll Context Overview
applicable for BE ATTR-21 Tariff Table
applicable for BE ATTR-22 Tariff Class Definition
applicable for BE ATTR-23 Local Vehicle Class Definition
applicable for BE ATTR-24 Time Class Definition
applicable for BE ATTR-25 User Class Definition
applicable for BE ATTR-31 Toll Context Layout
applicable for BE ATTR-31S Toll Context Layout for Section Pricing
applicable for BE ATTR-31A Toll Context Layout for Area Pricing
applicable for BE ATTR-31C Toll Context Layout for Cordon Pricing
applicable for FE CH Context Handling
applicable for FE CR Charge Report
= type of DUT FE Front End
BE Back End
x = Type of testing BV Valid Behaviour Tests
BI Invalid Behaviour Tests
= sequential (01-99) Test Purpose Number
number
5.4 Conformance test report

The supplier of the Front End and Back End, respectively, is responsible for providing a conformance test

report.

The supplier of the Front End shall complete the proforma conformance test report (PCTR) for Front End as

defined in Annex D.

The supplier of the Back End shall complete the proforma conformance test report (PCTR) for Back End as

defined in Annex E.
© ISO 2011 – All rights reserved 7
---------------------- Page: 19 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)
Annex A
(normative)
Test Purposes (TP) for Front End
A.1 Introduction

This annex contains the test purposes (TP) for the conformity evaluation of Front End to ISO/TS 17575-3.

A.1.1 TP symbols conventions

A special notation and symbol convention shall be used, as defined in what follows.

Symbols are used in the description of the TPs, with meanings according to Table A.1 below.

Table A.1 — Description of TP Symbols
SYMBOL DESCRIPTION
XXX.rq  The Tester sends the XXX.rq to the DUT
 YYY.rs The DUT sends the YYY.rs to the Tester
 YYY.rs = {attribute1, The DUT sends the YYY.rs to the Tester. YYY.rs shall not

attribute2, attribute3} consist of any attributes different than attribute1, attribute2,

attribute3. If any of attributes in the list is optional it may be
missing in YYY.rs.
 YYY.rs = {attribute1= The DUT sends the YYY.rs to the Tester with attribute1.
value1} Value of attribute1, i.e. value1 shall be stored by the tester
and will be utilized in further TP steps.
A ≡ B A “is equal to” B
A → B A “is transformed” into B
Ø Means “empty” or “not set”.
A.2 Context Handling

These test purposes apply to Iso17575-3Adu as claimed in ISO/TS 17575-3 Clause B.5.4.1/1, EFC Attributes

as claimed in ISO/TS 17575-3 Clause B.5.4.3/1-9.

NOTE 1 No claims related to optional items of PICS proforma are covered, as there is no means to observe any

behaviour of Front End proving support of these items.

NOTE 2 No test purposes for invalid behaviour are specified (BI), as ISO/TS 17575-3 does not specify any invalid

behaviour of Front End.

NOTE 3 No dynamic behaviour is covered by this specification. Dynamic behaviour is e.g. selection of applicable Tariff

Class by the Front End depending on vehicle, time, user, location criteria.
8 © ISO 2011 – All rights reserved
---------------------- Page: 20 ----------------------
SIST-TS CEN ISO/TS 16410-1:2011
ISO/TS 16410-1:2011(E)

NOTE 4 A Charge Report sent by the DUT may or may not include all data elements listed in the structure as almost all

of them are optional.
A.2.1 BV test purposes
Test subgroup objective:
 to test the behaviour of the DUT in relation to the context activation;
 to test the behaviour of the DUT in relation to handling of multiple contexts;
 to test usage of communication services by DUT,
by means of the syntactically and contextual correct ADUs:

 single ADU consisting of all necessary attributes to activate the context, and/or

 several consecutive ADUs consisting of all necessary attributes to activate the context.

TP/CH/FE/BV/01 Verify that DUT activates toll context – toll charger attribute check

TP Origin Specific
Reference ISO/TS 17575-3, Clause 8.1
Initial Condition Front End is initialized and can accept Context Data.
OBU belonging to the Front End is located within geographic borders defined
in Context Data.
Version of any data element of context data is known for the Front End.
No authentication is required by the Front End.
Stimulus and Expected Behaviour
Tester DUT
1 ContextData1 
2 Event defined in ContextData1 occu
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.