SIST EN 2813:2019

Aerospace series - Aluminium alloy AL-P-6061- - T6 - Drawn tube for pressure applications - 0,6 mm ≤ a ≤ 12,5 mm

This document specifies the requirements relating to:
Aluminium alloy AL-P-6061-
T6
Drawn tube for pressure applications
0,6 mm ≤ a ≤ 12,5 mm
for aerospace applications.

Luft- und Raumfahrt - Aluminiumlegierung AL-P-6061- - T6 - Kaltgezogene Hydraulikrohre - 0,6 mm ≤ a ≤ 12,5 mm

Série aérospatiale - Alliage d'aluminium AL-P-6061- - T6 - Tubes étirés pour applications sous pression - 0,6 mm ≤ a ≤ 12,5 mm

Le présent document spécifie les exigences relatives à :
Alliage d'aluminium AL-P-6061-
T6
Tubes étirés pour applications sous pression
0,6 mm ≤ a ≤ 12,5 mm
pour applications aérospatiales.

Aeronavtika - Aluminijeva zlitina AL-P-6061- - T6 - Vlečena cev za tlačno uporabo 0,6 mm ≤ a ≤ 12,5 mm

Ta dokument določa zahteve, ki se nanašajo na:
aluminijeve zlitine AL-P-6061-
T6
vlečene cevi za tlačno uporabo
0,6 mm ≤ a ≤ 12,5 mm
za uporabo v aeronavtiki.

General Information

• Status: Published
• Publication Date: 09-Dec-2018
• ICS: 49.025.20 - Aluminium
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 06-Dec-2018
• Due Date: 10-Feb-2019
• Completion Date: 10-Dec-2018
• Ref Project: EN 2813:2018 - Aerospace series - Aluminium alloy AL-P-6061- - T6 - Drawn tube for pressure applications - 0,6 mm ≤ a ≤ 12,5 mm

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.]RJHQH49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 2813:2018SIST EN 2813:2019en,fr,de01-februar-2019SIST EN 2813:2019SLOVENSKI
STANDARD



SIST EN 2813:2019



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2813
November
t r s z ICS
v {ä r t wä t r English Version
Aerospace series æ Aluminium alloy ALæPæ x r x sæ æ T x æ Drawn tube for pressure applications æ
rá x mm ≤ a ≤
s tá w mm Série aérospatiale æ Alliage d 5aluminium ALæPæ x r x sæ æ T x æ Tubes étirés pour applications sous pression æ
rá x mm ≤ a ≤
s tá w mm
Luftæ und Raumfahrt æ Aluminiumlegierung ALæPæ x r x sææ T x æ Kaltgezogene Hydraulikrohre æ
rá x mm ≤ a ≤
s tá w mm This European Standard was approved by CEN on
t v September
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
t z s uã t r s z ESIST EN 2813:2019



EN 2813:2018 (E) 2 Contents Page European foreword . 3 Introduction . 4 1 Scope .
w 2 Normative references .
w 3 Terms and definitions .
w 4 Requirements .
w
SIST EN 2813:2019



EN 2813:2018 (E) 3 European foreword This document (EN 2813:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This document shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2019, and conflicting national standards shall be withdrawn at the latest by May 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, S
...