oSIST prEN IEC 60335-2-72:2026

• Abstract:

  This Document deals with the safety of powered ride-on and powered walk-behind machines intended for commercial indoor or outdoor use for the following applications:; - sweeping,; - scrubbing,; - wet or dry pick-up,; - polishing,; - application of wax, sealing products and powder-based detergents,; - shampooing; of floors.; These machines have a cleaning motion which is more linear than lateral or periodic. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope:; - public use areas such as hotels, schools, hospitals;; - industrial locations, for example factories and manufacturing shops;; - retail outlets, for example shops and supermarkets;; - business premises, for example offices and banks;; - all uses other than normal housekeeping purposes.; These machines may be equipped with a traction drive system. The following power systems are covered:; - internal combustion engines,; - mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances,; - battery-operated machines.; Battery-operated machines may be equipped with a built-in battery charger.; This standard does not apply to; - floor treatment appliances for household use (IEC 60335-2-10);; - floor treatment machines for commercial use (IEC 60335-2-67);; - spray extraction machines for commercial use (IEC 60335-2-68);; - wet and dry vacuum cleaners, including power brush, for commercial use (IEC 60335-2-69);; - road sweepers;; - machines designed for use on slopes with a gradient exceeding 20 %;; - machines equipped with a power take-off (PTO);; - machines designed for use in corrosive or explosive environments (dust, vapour or gas);; - machines designed for picking up hazardous dusts (as defined in IEC 60335-2-69), inflammable substances, or glowing particles;; - machines designed for use in vehicles or on board of ships or aircraft.

• Status: Not Published
• Public Enquiry End Date: 26-Nov-2026
• ICS: 97.080 - Cleaning appliances
• Technical Committee: VGA - Safety of household and similar electrical appliances
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 10-Sep-2026
• Due Date: 28-Jan-2027
• Ref Project: prEN IEC 60335-2-72:2026 - Household and similar electrical appliances - Safety - Part 2-72: Particular requirements for floor treatment machines with or without traction drive, for commercial use

• Refers: SIST EN ISO 5353:1999 - Earth-moving machinery, and tractors and machinery for agriculture and forestry - Seat index point (ISO 5353:1995)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 3411:2008 - Earth-moving machinery - Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-3:2019 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 3: Series development, hardware and software (ISO 25119-3:2018)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-4:2023 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 4: Production, operation, modification and supporting processes (ISO 25119-4:2018)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-2:2023 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 2: Concept phase (ISO 25119-2:2019)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-1:2023/A1:2023 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 1: General principles for design and development - Amendment 1 (ISO 25119-1:2018/Amd 1:2020)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-3:2023 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 3: Series development, hardware and software (ISO 25119-3:2018)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-3:2023/A1:2023 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 3: Series development, hardware and software - Amendment 1 (ISO 25119-3:2018/Amd 1:2020)
• Effective Date: 14-Jul-2026
• Refers: SIST EN 60068-2-78:2013 - Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-4:2019 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 4: Production, operation, modification and supporting processes (ISO 25119-4:2018)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-1:2019 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 1: General principles for design and development (ISO 25119-1:2018)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 13849-1:2023 - Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2023)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-4:2023/A1:2023 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 4: Production, operation, modification and supporting processes - Amendment 1 (ISO 25119-4:2018/Amd 1:2020)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 25119-1:2023 - Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 1: General principles for design and development (ISO 25119-1:2018)
• Effective Date: 14-Jul-2026
• Refers: SIST EN ISO 13857:2020 - Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2019)
• Effective Date: 14-Jul-2026

SLOVENSKI STANDARD
01-november-2026
Gospodinjski in podobni električni aparati - Varnost - 2-72. del: Posebne zahteve
za stroje za nego tal, z ali brez pogona, za komercialno uporabo
Household and similar electrical appliances - Safety - Part 2-72: Particular requirements
for floor treatment machines with or without traction drive, for commercial use
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-72:
Besondere Anforderungen für Bodenbehandlungsmaschinen, mit oder ohne Fahrantrieb,
für den gewerblichen Gebrauch
Appareils électrodomestiques et analogues - Sécurité - Partie 2-72: Exigences
particulières pour les machines de traitements des sols avec ou sans commande de
dispositif de déplacement, à usage commercial
Ta slovenski standard je istoveten z: prEN IEC 60335-2-72:2026
ICS:
97.080 Aparati za čiščenje Cleaning appliances
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD DRAFT
prEN IEC 60335-2-72
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2026
ICS 97.080 Will supersede EN 60335-2-72:2012
English Version
Household and similar electrical appliances - Safety - Part 2-72:
Particular requirements for floor treatment machines with or
without traction drive, for commercial use
(IEC 60335-2-72:2021)
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-72: Exigences particulières pour les machines de ähnliche Zwecke - Teil 2-72: Besondere Anforderungen für
traitements des sols avec ou sans commande de dispositif Bodenbehandlungsmaschinen, mit oder ohne Fahrantrieb,
de déplacement, à usage commercial für den gewerblichen Gebrauch
(IEC 60335-2-72:2021) (IEC 60335-2-72:2021)
This draft European Standard is submitted to CENELEC members for enquiry.
Deadline for CENELEC: 2026-11-27.

The text of this draft consists of the text of IEC 60335-2-72:2021.

If this draft becomes a European Standard, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CENELEC in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to
the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Project: 82795 Ref. No. prEN IEC 60335-2-72:2026 E

1 European foreword
2 This document (prEN IEC 60335-2-72:2026) consists of the text of IEC 60335-2-72:2021 prepared by
3 IEC/TC 61 "Safety of household and similar electrical appliances".
4 This document is currently submitted to the Enquiry.
5 The following dates are proposed:
• latest date by which the existence of this (doa) dav + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dav + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dav + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)
6 This document will supersede EN IEC 60335-2-72:2012 and all of its amendments and corrigenda (if any).
7 This document is read in conjunction with prEN IEC 60335-2-72:2026/prAA:2026.
IEC 60335-2-72 ®
Edition 5.0 2021-07
INTERNATIONAL
STANDARD
colour
inside
Household and similar electrical appliances – Safety –

Part 2-72: Particular requirements for floor treatment machines with or without

traction drive, for commercial use

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 97.080 ISBN 978-2-8322-9995-1

– 2 – IEC 60335-2-72:2021 © IEC 2021
CONTENTS
FOREWORD . 4
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 9
3 Terms and definitions . 10
4 General requirement . 14
5 General conditions for the tests . 14
6 Classification . 15
7 Marking and instructions . 15
8 Protection against access to live parts . 19
9 Starting of motor-operated appliances . 21
10 Power input and current . 21
11 Heating . 21
12 Charging of metal-ion batteries . 21
13 Leakage current and electric strength at operating temperature . 21
14 Transient overvoltages . 22
15 Moisture resistance . 22
16 Leakage current and electric strength . 23
17 Overload protection of transformers and associated circuits . 24
18 Endurance . 24
19 Abnormal operation . 24
20 Stability and mechanical hazards . 25
21 Mechanical strength . 30
22 Construction . 32
23 Internal wiring . 36
24 Components . 37
25 Supply connection and external flexible cords . 38
26 Terminals for external conductors . 39
27 Provision for earthing . 39
28 Screws and connections . 39
29 Clearances, creepage distances and solid insulation . 39
30 Resistance to heat and fire . 40
31 Resistance to rusting . 40
32 Radiation, toxicity and similar hazards . 40
Annexes . 46
Annex A (informative) Routine tests . 47
Annex B (normative) Battery-operated appliances, separable batteries and detachable
batteries for battery-operated appliances . 48
Annex L (informative) Guidance for the measurement of clearances and creepage
distances . 53
Annex AA (normative) Precast paving slabs . 54

IEC 60335-2-72:2021 © IEC 2021 – 3 –
Annex BB (normative) Requirements for internal combustion engine powered
machines using liquefied petroleum gas (LPG) . 55
Annex CC (normative) Falling-object protective structures (FOPS) – Dynamic test and

performance requirements . 58
Annex DD (informative) Emission of acoustical noise . 61
Annex EE (informative) Emission of vibration . 64
Bibliography . 65
Index of defined terms . 67

Figure 101 – Impact test apparatus . 41
Figure 102 – Apparatus for testing the abrasion resistance of current-carrying hoses . 42
Figure 103 – Apparatus for testing the resistance to flexing of current-carrying hoses . 43
Figure 104 – Configuration of the hose for the freezing treatment . 43
Figure 105 – Flexing positions for the hose after removal from the freezing cabinet . 44
Figure 106 – Warning symbol: Do not inhale exhaust fumes . 44
Figure 107 – Circuit for testing battery chargers (taken from IEC 60335-2-29) . 45
Figure CC.1 – Satisfactory protection by the overhead guard . 59
Figure CC.2 – Admissible deformation when the overhead guard is supported at all
sides . 60
Figure CC.3 – Admissible deformation when the overhead guard is supported at one
side . 60

Table 101 – Machine classification . 15
Table 12 – Pull force and torque . 39
Table DD.1 – Determination of uncertainty . 63

– 4 – IEC 60335-2-72:2021 © IEC 2021
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –
Part 2-72: Particular requirements for floor treatment machines
with or without traction drive, for commercial use

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 60335-2-72 has been prepared by subcommittee 61J: Electrical motor-operated cleaning
appliances for commercial use, of IEC technical committee 61: Safety of household and
similar electrical appliances. It is an International Standard.
This fifth edition cancels and replaces the fourth edition published in 2016. It constitutes a
technical revision.
This edition includes the following significant technical changes with respect to the previous
edition (minor changes are not listed):
– editorial and technical alignment with IEC 60335-1:2020;
– rearrangement of subclauses to consistent numbering 22.101 to 22.113.

IEC 60335-2-72:2021 © IEC 2021 – 5 –
The text of this International Standard is based on the following documents:
CDV Report on voting
61J/738/CDV 61J/744A/RVC
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement,
available at www.iec.ch/members_experts/refdocs. The main document types developed by
IEC are described in greater detail at www.iec.ch/standardsdev/publications.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its
amendments. It was established on the basis of the sixth edition (2020) of that standard.
NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60335-1.
This part 2 supplements or modifies the corresponding clauses in IEC 60335-1, so as to
convert that publication into the IEC standard: Particular requirements for floor treatment
machines with or without traction drive, for commercial use.
When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies
as far as is reasonable. When this standard states “addition”, “modification” or “replacement”,
the relevant text in Part 1 is to be adapted accordingly.
NOTE 2 The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
– unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including
those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
NOTE 3 The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
NOTE 4 The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 12 months or later than 36 months from the date of publication.
The following differences exist in the countries indicated below.
– Annex AA: The CO-emission of LPG driven machines, intended to be used indoors, has to comply with the
value specified in Annex BB. The result shall be documented (Germany).
– Annex BB: For machines intended to be used indoors, except single cylinder engines, the exhaust gas shall
not contain more than 0,1 % volume of carbon monoxide (CO). If adjustments are necessary, the adjusting
means shall be easily accessible. The measurement shall be carried out with a warm engine, idling, using
98 % propane. The revolution speed of the engine shall be documented (Germany).
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.
A list of all parts of the IEC 60335 series, under the general title: Household and similar
electrical appliances – Safety, can be found on the IEC website.

– 6 – IEC 60335-2-72:2021 © IEC 2021
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates that it
contains colours which are considered to be useful for the correct understanding of its
contents. Users should therefore print this document using a colour printer.

IEC 60335-2-72:2021 © IEC 2021 – 7 –
INTRODUCTION
It has been assumed in the drafting of this International Standard that the execution of its
provisions is entrusted to appropriately qualified and experienced persons.
This standard recognizes the internationally accepted level of protection against hazards such
as electrical, mechanical, thermal, fire and radiation of appliances when operated as in
normal use taking into account the manufacturer's instructions. It also covers abnormal
situations that can be expected in practice and takes into account the way in which
electromagnetic phenomena can affect the safe operation of appliances.
This standard takes into account the requirements of IEC 60364 as far as possible so that
there is compatibility with the wiring rules when the appliance is connected to the supply
mains. However, national wiring rules may differ.
If an appliance within the scope of this standard also incorporates functions that are covered
by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as
far as is reasonable. If applicable, the influence of one function on the other is taken into
account.
When a part 2 standard does not include additional requirements to cover hazards dealt with
in Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
This standard is a product family standard dealing with the safety of appliances and takes
precedence over horizontal and generic standards covering the same subject.
NOTE 2 Horizontal and generic standards covering a hazard are not applicable since they have been taken into
consideration when developing the general and particular requirements for the IEC 60335 series of standards. For
example, in the case of temperature requirements for surfaces on many appliances, generic standards, such as
ISO 13732-1 for hot surfaces, are not applicable in addition to Part 1 or part 2 standards.
An appliance that complies with the text of this standard will not necessarily be considered to
comply with the safety principles of the standard if, when examined and tested, it is found to
have other features that impair the level of safety covered by these requirements.
An appliance employing materials or having forms of construction differing from those detailed
in the requirements of this standard may be examined and tested according to the intent of
the requirements and, if found to be substantially equivalent, may be considered to comply
with the standard.
– 8 – IEC 60335-2-72:2021 © IEC 2021
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –
Part 2-72: Particular requirements for floor treatment machines
with or without traction drive, for commercial use

1 Scope
This clause of Part 1 is replaced by the following.
This part of IEC 60335 deals with the safety of powered ride-on and powered walk-behind
machines intended for commercial indoor or outdoor use for the following applications:
– sweeping,
– scrubbing,
– wet or dry pick-up,
– polishing,
– application of wax, sealing products and powder-based detergents,
– shampooing
of floors.
These machines have a cleaning motion which is more linear than lateral or periodic.
NOTE 101 By contrast, the cleaning motion of machines covered by IEC 60335-2-67 is more lateral or periodic
than linear.
NOTE 102 This standard applies to machines for commercial use. The following list, although not
comprehensive, gives an indication of locations that are included in the scope:
– public use areas such as hotels, schools, hospitals;
– industrial locations, for example factories and manufacturing shops;
– retail outlets, for example shops and supermarkets;
– business premises, for example offices and banks;
– all uses other than normal housekeeping purposes.
These machines may be equipped with a traction drive system. The following power systems
are covered:
– internal combustion engines,
– mains powered motors up to a rated voltage of 250 V for single-phase appliances and
480 V for other appliances,
– battery-operated machines.
Battery-operated machines may be equipped with a built-in battery charger.
This standard does not apply to
– floor treatment appliances for household use (IEC 60335-2-10);
– floor treatment machines for commercial use (IEC 60335-2-67);
– spray extraction machines for commercial use (IEC 60335-2-68);
– wet and dry vacuum cleaners, including power brush, for commercial use
(IEC 60335-2-69);
IEC 60335-2-72:2021 © IEC 2021 – 9 –
NOTE 103 IEC 60335-2-67, IEC 60335-2-68 and IEC 60335-2-69 cover only machines without traction drive.
– road sweepers;
NOTE 104 In Europe, EN 13019 covers road sweepers.
– machines designed for use on slopes with a gradient exceeding 20 %;
– machines equipped with a power take-off (PTO);
– machines designed for use in corrosive or explosive environments (dust, vapour or gas);
– machines designed for picking up hazardous dusts (as defined in IEC 60335-2-69),
inflammable substances, or glowing particles;
– machines designed for use in vehicles or on board of ships or aircraft.
NOTE 105 Attention is drawn to the fact that
– in many countries additional requirements on the safe use of the equipment covered can be specified by the
national health authorities, the national authorities responsible for the protection of labour, the national water
supply authorities and similar authorities;
– ride-on machines designed for transport over public roads can be subject to additional requirements (e.g.
lighting, license plate etc.).
NOTE 106 Requirements for fuel-cells are under consideration.
2 Normative references
This clause of Part 1 is applicable except as follows.
Addition:
IEC 62061, Safety of machinery – Functional safety of safety-related control systems
IEC 62485-3:2014, Safety requirements for secondary batteries and battery installations –
Part 3: Traction batteries
IEC TS 62885-1, Surface cleaning appliances – Part 1: General requirements on test material
and test equipment
ISO 3411, Earth moving machinery – Physical dimensions of operators and minimum operator
space envelope
ISO 5353, Earth-moving machinery, and tractors and machinery for agriculture and forestry –
Seat index point
ISO 6344-2, Coated abrasives – Grain size analysis – Part 2: Determination of grain size
distribution of macrogrits P12 to P220
ISO 13849-1, Safety of machinery – Safety-related parts of control systems – Part 1: General
principles for design
ISO 13857:2019, Safety of machinery – Safety distances to prevent hazard zones being
reached by the upper and lower limbs
ISO 25119 (all parts), Tractors and machinery for agriculture and forestry – Safety-related
parts of control systems
Replacement:
IEC 60068-2-78:2012, Environmental testing – Part 2-78: Tests – Test Cab: Damp heat,
steady state
– 10 – IEC 60335-2-72:2021 © IEC 2021
3 Terms and definitions
This clause of Part 1 is applicable except as follows.
3.1.9 Replacement:
normal operation
conditions under which the machine is operated in normal use, as intended by the
manufacturer
It denotes the load corresponding to the rated power input or the highest obtainable load of
all particular loads of the various functions that can be operated at the same time in
accordance with the manufacturer’s instructions. For machines provided with a seat or an
operator platform, a mass of 75 kg secured in position at the appropriate height is used to
simulate the operator in the most unfavourable position. Internal combustion engine driven
machines are operated with the fuel specified by the manufacturer except where otherwise
stated in this standard.
Operational functions include all treatment and driving functions.
Operation of the machine under following conditions:
– the battery is charged, the battery being initially discharged to such an extent that the
appliance cannot operate;
– if possible, the appliance is supplied from the supply mains through its standalone battery
charger, the battery being initially discharged to such an extent that the appliance cannot
operate. The appliance is operated as specified in the main part of this standard;
– if possible, built-in battery chargers are connected to the circuit of Figure 107. The
variable resistor is adjusted so that the current in the circuit is the rated DC output
current when the battery charger is supplied at rated voltage. When the charging current
is controlled by the state of charge of the battery, the variable resistor and the capacitor
are replaced by a discharged battery of the type and having the largest capacity specified
in the instructions.
– if the appliance incorporates inductive coupling between two parts that are detachable
from each other, the appliance is supplied from the supply mains with the detachable part
removed.
The normal operation related to the operational functions is specified in 3.1.9.101 to
3.1.9.103:
3.1.9.101 Scrubbing and sweeping machines are operated on a surface of hydraulically
pressed concrete paving slabs (see normative Annex AA) intermittently at least 30 min
switched on, and for a period of 5 min switched off.
An alternative is a smooth concrete area of a surface consistency comparable with
hydraulically pressed concrete paving slabs.
3.1.9.102 Polishing and dry buffing machines are operated as follows.
PVC- or comparable flooring surfaces are considered to be suitable for establishing normal
operation. The peak of input occurring during the drying process of the chemical applied to
treat the surface is not taken as normal operation but is averaged by extending
measurements over a period of at least 10 min.
3.1.9.103 Carpet shampooers are operated on a test surface consisting of a carpet, in
accordance with IEC TS 62885-1, the carpet being fastened to the floor.
Prior to testing, the brush of the shampooing machine is conditioned by operating it for 15 min
on a clean, dry concrete surface. After running on the concrete surface, the brush is
immersed in a shampoo solution for at least 30 min.
The solution tank is filled and the machine is operated over a period of 10 min.

IEC 60335-2-72:2021 © IEC 2021 – 11 –
3.6.9 Addition:
Note 101 to entry: Sets of batteries are regarded as a single battery if they require tools to disconnect the
individual battery interconnections.
3.101
traction drive
system used to propel the machine, e.g. by powered wheels
Note 1 to entry: Traction by the effect of rotating brushes is not included.
3.102
walk-behind machine
machine with or without a traction drive designed to be controlled by the operator walking
behind the machine
It may be equipped with a detachable sulky.
3.103
ride-on machine
machine with a traction drive and with an operator seat or a platform on which the operator
is sitting/standing during operation
3.104
sulky (trailer)
removable trailing seat or stand-on platform with wheels or skids designed to carry an
operator in a sitting or standing position, while controlling a walk-behind machine with
traction drive
3.105
wet cleaning machine
machine for applying and sucking up liquids
3.106
water-suction cleaning machine
machine for sucking up liquids
3.107
motorized cleaning head
hand-held or hand-guided cleaning device connected to the machine, with an integrated
electrical motor
Note 1 to entry: The main cleaning head permanently attached is not regarded as a motorized cleaning head.
3.108
hopper
container to store picked up debris
3.109
parking brake
means, actuated by the operator in the normal operating position, to prevent a stationary
machine from moving
3.110
service brake
means for decelerating and stopping a machine, with a traction drive, from its ground travel
speed
– 12 – IEC 60335-2-72:2021 © IEC 2021
3.111
operator presence control
OPC
control device that automatically interrupts the power, e.g. to a drive or an engine, when the
operator's actuating force is removed
Note 1 to entry: Such devices can be, for example, continuous action controls ("hold-to-run" controls) or seat
switches.
3.112
guard
part of the machine specifically designed to provide protection by means of a physical barrier,
such as, for example, a casing, a shield, a cover, a screen, a door, an enclosure or a fence;
other parts of the machine that fulfil a primarily operational function, such as, for example, the
frame of the machine, may also fulfil a protective function but are not referred to as guards
Note 1 to entry: Three main kinds of guards can be distinguished: fixed guards, interlocking moveable guards
and adjustable guards. Interlocking movable guards are required where frequent access is envisaged, while fixed
guards can be used where frequent access is not envisaged.
3.113
operator
person in direct physical contact with the machine and performing one or more of the
following tasks: installing, operating, adjusting, cleaning, moving, or performing user
maintenance on the machine
3.114
gross vehicle weight
GVW
maximum allowable fully laden weight of the machine and its payload, as ready for use
Note 1 to entry: See 5.102 for further test conditions.
3.115
test solution
solution which consists of 20 g of NaCl and 1 ml of a solution of 28 % by mass of dodecyl
sodium sulphate in each 8 l of water
Note 1 to entry: The chemical designation of dodecyl sodium sulphate is C H NaSO .
12 25 4
3.116
level surface
plane with a gradient up to and including 2 %
3.117
slope
inclined plane with a gradient greater than 2 % but not exceeding 20 %
3.118
maximum cleaning gradeability
maximum gradient according to manufacturer's instruction and as indicated on the machine,
on which the machine can be used safely for cleaning purposes
3.119
maximum transport gradeability
maximum gradient according to manufacturer's instruction, on which the machine can be used
safely for transport purposes
IEC 60335-2-72:2021 © IEC 2021 – 13 –
3.120
built-in charger
charger mounted on or into the machine and designed to operate only on or into the machine
Note 1 to entry: Built-in battery chargers can also be called on-board chargers.
3.121
built-in charger with power supply function
component intended to provide power for charging, operation or both
3.122
commercial use
intended use of machines covered by this standard, i.e. not intended for normal housekeeping
purposes by private persons but which may be a source of danger to the public
I.e. in particular that
– the machines may be used by cleaning contractors, cleaning staff, etc.;
– they are used in commercial or public premises (i.e. offices, shops, hotels, hospitals,
schools, etc.) or in industrial (plants etc.) and light industrial (workshops etc.)
environments.
Note 1 to entry: Commercial use is also called professional use.
3.123
battery low voltage
BLV
battery-supplied floating DC working voltage in the range of >42 V and ≤60 V
Batteries of BLV systems may be charged with voltages up to 75 V DC. All voltages are
regarded as DC if the peak-to-peak value does not exceed 10 % of the average value.
Note 1 to entry: BLV is not considered to be of class I, class II, or class III.
3.124
hazardous voltage
voltage between parts having an average value exceeding 60 V DC or 42 V peak when the
peak-to-peak ripple exceeds 10 % of the average value
3.125
battery connector
plug connecting system applied for the connection of the battery either with the charging
system, or with the machine, which can be engaged and disengaged without the use of any
tools
3.126
BLV insulation
insulation applied to live parts to provide basic protection against electric shock and which is
identical with basic insulation in the voltage range defined by BLV
3.127
rated DC output voltage
output voltage assigned to the battery charger by the manufacturer
3.128
rated DC output current
output current assigned to the battery charger by the manufacturer

– 14 – IEC 60335-2-72:2021 © IEC 2021
4 General requirement
This clause of Part 1 is applicable except as follows:
Replacement of the first paragraph by the following:
Machines shall be constructed so that they function safely so as to cause no danger to
persons or surroundings during normal use, even in the event of carelessness, and during
installation, adjusting, maintenance, cleaning, repairing or transportation.
Addition:
For the purposes of this standard, the term ‘appliance’ as used in Part 1 is to be read as
‘machine’.
5 General conditions for the tests
This clause of Part 1 is applicable except as follows.
5.8.1 Addition:
When measuring voltage, the peak value of any superimposed ripple exceeding 10 % of the
average value shall be included. Transient voltages are ignored, such as a temporary
increase of voltage, for example after the battery is disconnected from the charging circuit.
5.17 Modification:
Built-in chargers in compliance with IEC 60335-2-29 do not need to be retested, except for
Clauses 6, 7, 11, 15, 19 and 22.
Clause 29 needs to be reevaluated if the pollution degree of the microenvironment for the
battery charger is 1 or 2 unless the insulation is enclosed or located so that it is unlikely to be
exposed to pollution due to normal use of the machine.
5.101 The test solution is to be stored in a cool atmosphere and used within seven days
after its preparation.
5.102 The GVW includes, if applicable, full clean water tanks, empty dirty water tanks (half
full for recycling systems), empty dust bags, hopper loaded at rated capacity, largest
recommended batteries, all options such as cords, hoses, wands, cleaning agents, brooms
and brushes.
For ride-on machines, the GVW includes a standard operator, weighing 75 kg.
5.103 Liquid containers of machines for wet scrubbing and shampooing are filled to the
highest level indicated by the manufacturer.
5.104 Machines that are designed to have a sulky are tested with the sulky including the
weight of a standard operator (75 kg) or without the sulky, whichever is the most
unfavourable condition.
5.105 Combustion engine-powered machines shall be supplied with the fuel as specified by
the manufacturer, except if stated elsewhere in this standard.

IEC 60335-2-72:2021 © IEC 2021 – 15 –
6 Classification
This clause of Part 1 is applicable except as follows.
6.1 Replacement:
Machines shall be one of the following classes with respect to the protection against electric
shock (see Table 101):
Table 101 – Machine classification
Working voltage DC Working voltage AC Classification Classification
mains-supplied circuits battery-supplied circuits
≤ 42 V (SELV) ≤ 42 V (SELV) Class III Not classified
≤ 42 V (ELV) ≤ 42 V (ELV) Class I or II Not classified

> 42 V and ≤ 60 V Class I or II BLV; special conditions
apply as given in
(≤75 V during
normative Annex B.
charging mode)
(BLV);
> 60 V (> 75 V during Class I or II Not classified
> 42 V
charging mode)
Compliance is checked by inspection and by the relevant tests.
6.2 Addition:
Mains supplied and battery powered machines for indoor use intended for dry cleaning only
shall be at least IPX0. Other machines shall be at least IPX3.
7 Marking and instructions
This clause of Part 1 is applicable except as follows.
7.1 Modification:
Replace the fourth dashed item as follows:
– the business name and address of the manufacturer and, if applicable, his authorized
representative; any address shall be sufficient to ensure postal contact;
Addition:
Machines shall be marked in addition with the following:
– serial number, if any;
– designation of the machine and series or type, allowing the technical identification of the
product. This may be achieved by a combination of letters and/or numbers;
NOTE 101 Designation of machine, series or type includes the model or type reference as required in Part 1.
– year of construction, i.e. the year in which the manufacturing process is completed;
NOTE 102 The year of construction can be part of the serial number.
– GVW of the machine, in kg;
– 16 – IEC 60335-2-72:2021 © IEC 2021
– the symbol indicating the maximum cleaning gradeability, with the value of x.
NOTE 103 I.e. the machine might be able to drive on a higher gradient (maximum transport gradeability). This
additional information can be given also in the instructions for use.
Machines intended to be used indoors and powered by internal combustion engines shall be
marked in addition with the symbol according to Figure 106. It is acceptable to show this
symbol in monochrome colour.
7.1.101 Motorized cleaning heads shall be marked with
– rated voltage or rated voltage range in volts;
– rated power input in watts;
– name, trademark or identification mark of the manufacturer or responsible vendor;
– model or type reference;
– mass of the most usual configuration in kg.
Motorized cleaning heads for water-suction cleaning appliances, except those of class III
construction having a working voltage up to 24 V shall be marked with symbol
IEC 60417-5935 (2012-09).
NOTE This symbol is an information sign and, except for the colours, the rules of ISO 3864-1 apply.
Compliance is checked by inspection.
7.6 Addition:
x %
maximum cleaning gradeability ‘x’

[symbol IEC 60417-5935 motorized cleaning head for water-
(2012-09)] suction cleaning
7.12 Modification:
Delete the first paragraph and the first warning.
Add after the Note th
...