iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 14630:2000

(Main)

Non-active surgical implants - General requirements (ISO 14630:1997)

Non-active surgical implants - General requirements (ISO 14630:1997)

This European Standard specifies general requirements for non-active surgical implants.  This standard is not applicable to dental implants, dental restorative materials, transendodontic and transradicular implants and intra-ocular lenses.  With regard to safety, this standard gives requirements for intended performance, design attributes, materials, design evaluation, manufacture, sterilization, packaging and information supplied by the manufacturer, and tests.  Tests required to be used to demonstrate compliance with this standard are contained in other levels.

Nichtaktive chirurgische Implantate - Allgemeine Anforderungen (ISO 14630:1997)

Diese Europäische Norm legt allgemeine Anforderungen für nichtaktive chirurgische Implantate fest. Diese Norm gilt nicht für Dentalimplantate, transendodontische und transradikuläre Implantate sowie Intraokularlinsen. In Bezug auf die Sicherheit legt diese Norm Anforderungen für die beabsichtigte Funktion, Konstruktionsmerkmale, Werkstoffe, Designprüfung, Herstellung, Sterilisation, Verpackung und die Bereitstellung von Informationen durch den Hersteller sowie Prüfverfahren fest.

Implants chirurgicaux non actifs - Exigences générales (ISO 14630:1997)

La présente norme européenne spécifie les exigences générales relatives aux implants chirurgicaux non actifs. Elle ne s'applique ni aux implants dentaires, ni aux produits utilisés en médecine dentaire restauratrice, ni aux implants transendodontiques et transradiculaires et ne concerne pas non plus verres intraoculaires.

Neaktivni kirurški vsadki (implantati) - Splošne zahteve (ISO 14630:1997)

General Information

Status
Withdrawn
Publication Date
31-Dec-1999
Withdrawal Date
30-Jun-2005
ICS
11.040.40 - Implants for surgery, prosthetics and orthotics
Technical Committee
VAZ - Healthcare
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jul-2005
Due Date
01-Jul-2005
Completion Date
01-Jul-2005
Directive
93/42/EEC - Council Directive 93/42/EEC of 14 June 1993 concerning medical devices
Mandate
M/023 - Standardization mandate to CEN/CENELEC concerning the development of European standards relating to medical devices
Ref Project
EN ISO 14630:1997 - Non-active surgical implants - General requirements (ISO 14630:1997)

Relations

Child
SIST EN 12011:2000 - Instrumentation to be used in association with non-active surgical implants - General requirements
Effective Date
22-Dec-2008
Replaced By
SIST EN ISO 14630:2005 - Non-active surgical implants - General requirements (ISO 14630:2005)
Effective Date
01-Jul-2005

Buy Standard

EN ISO 14630:2000EN ISO 14630:2000
PreviousNext
Standard
EN ISO 14630:2000
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 14630:2000
01-januar-2000
Neaktivni kirurški vsadki (implantati) - Splošne zahteve (ISO 14630:1997)
Non-active surgical implants - General requirements (ISO 14630:1997)
Nichtaktive chirurgische Implantate - Allgemeine Anforderungen (ISO 14630:1997)
Implants chirurgicaux non actifs - Exigences générales (ISO 14630:1997)
Ta slovenski standard je istoveten z: EN ISO 14630:1997
ICS:
11.040.40 Implantanti za kirurgijo, Implants for surgery,
protetiko in ortetiko prosthetics and orthotics
SIST EN ISO 14630:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14630:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 14630:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 14630:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 14630:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 14630:20
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 14708-3:2023(Main)
Implants for surgery - Active implantable medical devices - Part 3: Implantable neurostimulators (ISO 14708-3:2017)
EN ISO 14708-3:2022

ISO 14708-3:2008 is applicable to active implantable medical devices intended for electrical stimulation of the central or peripheral nervous system.
ISO 14708-3:2008 is also applicable to all non-implantable parts and accessories of the devices.
The tests that are specified in ISO 14708-3:2008 are type tests intended to be carried out on a sample of a device to show compliance, and are not intended to be used for the routine testing of manufactured products.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 21917:2023(Main)
Anaesthetic and respiratory equipment - Voice prostheses (ISO 21917:2021)
EN ISO 21917:2022

This document specifies performance requirements for voice prostheses including requirements for marking, packaging and information to be provided by the manufacturer as well as test methods for the evaluation of physical characteristics of voice prostheses.
NOTE      There is guidance or rationale for this list item contained in A.2.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5832-6:2022(Main)
Implants for surgery - Metallic materials - Part 6: Wrought cobalt-nickel-chromium-molybdenum alloy (ISO 5832-6:2022)
EN ISO 5832-6:2022

This document specifies the characteristics of, and corresponding test methods for, wrought cobaltnickel chromium-molybdenum alloy for use in the manufacture of surgical implants.
NOTE The tensile properties of a sample obtained from a finished product made of this alloy do not
necessarily comply with those specified in this document

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 9713:2022(Main)
Neurosurgical implants - Self-closing intracranial aneurysm clips (ISO 9713:2022)
EN ISO 9713:2022

This document establishes the characteristics of self-closing aneurysm clips intended for permanent
intracranial implantation and specifies requirements for their marking, packaging, sterilization and
for labelling and accompanying documentation. In addition, it gives a method for the measurement of
closing force.
This document is not applicable to malleable clips, or clips intended to be used during the course of
surgery and removed before wound closure (temporary clips).
NOTE In this document when not otherwise established, the term “implant” refers to the self-closing
intracranial aneurysm clips.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5832-3:2022(Main)
Implants for surgery - Metallic materials - Part 3: Wrought titanium 6-aluminium 4-vanadium alloy (ISO 5832-3:2021)
EN ISO 5832-3:2021

This document specifies the characteristics of, and corresponding test methods for, the wrought
titanium alloy known as titanium 6-aluminium 4-vanadium alloy (Ti-6Al-4V alloy) for use in the
manufacture of surgical implants.
NOTE The mechanical properties of a sample obtained from a finished product made of this alloy might not
necessarily comply with the specifications given in this document.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5840-2:2021(Main)
Cardiovascular implants - Cardiac valve prostheses - Part 2: Surgically implanted heart valve substitutes (ISO 5840-2:2021)
EN ISO 5840-2:2021

This document is applicable to heart valve substitutes intended for implantation in human hearts,
generally requiring cardiopulmonary bypass and generally with direct visualization. See Annex E for
examples of surgical heart valve substitutes and their components.
This document is applicable to both newly developed and modified surgical heart valve substitutes and
to the accessory devices, packaging, and labelling required for their implantation and for determining
the appropriate size of the surgical heart valve substitute to be implanted.
This document establishes an approach for verifying/validating the design and manufacture of a
surgical heart valve substitute through risk management. The selection of appropriate qualification
tests and methods are derived from the risk assessment. The tests can include those to assess the
physical, chemical, biological, and mechanical properties of surgical heart valve substitutes and of
their materials and components. The tests can also include those for pre-clinical in vivo evaluation and
clinical evaluation of the finished surgical heart valve substitute.
This document defines operational conditions and performance requirements for surgical heart valve
substitutes where adequate scientific and/or clinical evidence exists for their justification.
For some heart valve substitutes (e.g. sutureless), the requirements of both this document and
ISO 5840-3:2021 can be relevant and are considered as applicable to the specific device design and are
based on the results of the risk analysis.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5840-3:2021(Main)
Cardiovascular implants - Cardiac valve prostheses - Part 3: Heart valve substitutes implanted by transcatheter techniques (ISO 5840-3:2021)
EN ISO 5840-3:2021

This document is applicable to all devices intended for implantation as a transcatheter heart valve substitute.
This document is applicable to transcatheter heart valve substitutes and to the accessory devices, packaging and labelling required for their implantation and for determining the appropriate size of heart valve substitute to be implanted.
This document establishes an approach for verifying/validating the design and manufacture of a transcatheter heart valve substitute through risk management. The selection of appropriate verification/validation tests and methods are to be derived from the risk assessment. The tests can include those to assess the physical, chemical, biological and mechanical properties of heart valve substitutes and of their materials and components. The tests can also include those for preclinical in vivo evaluation and clinical evaluation of the finished heart valve substitute.
This document defines operational conditions and performance requirements for transcatheter heart valve substitutes where adequate scientific and/or clinical evidence exists for their justification.
This document includes considerations for implantation of a transcatheter heart valve substitute inside a pre-existing prosthetic device (e.g. valve-in-valve and valve-in-ring configurations).

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5840-1:2021(Main)
Cardiovascular implants - Cardiac valve prostheses - Part 1: General requirements (ISO 5840-1:2021)
EN ISO 5840-1:2021

This document is applicable to heart valve substitutes intended for implantation and provides general
requirements. Subsequent parts of the ISO 5840 series provide specific requirements.
This document is applicable to newly developed and modified heart valve substitutes and to the
accessory devices, packaging, and labelling required for their implantation and for determining the
appropriate size of the heart valve substitute to be implanted.
ISO 5840-1 outlines an approach for verifying/validating the design and manufacture of a heart valve
substitute through risk management. The selection of appropriate qualification tests and methods
are derived from the risk assessment. The tests can include those to assess the physical, chemical,
biological, and mechanical properties of heart valve substitutes and of their materials and components.
The tests can also include those for preclinical in vivo evaluation and clinical evaluation of the finished
heart valve substitute.
ISO 5840-1 defines operational conditions for heart valve substitutes.
ISO 5840-1 furthermore defines terms that are also applicable to ISO 5840-2 and ISO 5840-3.
ISO 5840-1 does not provide requirements specific to homografts, tissue engineered heart valves
(e.g. valves intended to regenerate in vivo), and heart valve substitutes designed for implantation in
circulatory support devices. Some of the provisions of ISO 5840-1 can be applied to valves made from
human tissue that is rendered non-viable.
NOTE A rationale for the provisions of ISO 5840-1 is given in Annex A.

  • Standard
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    78 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 25539-2:2020(Main)
Cardiovascular implants - Endovascular devices - Part 2: Vascular stents (ISO 25539-2:2020)
EN ISO 25539-2:2020

This document specifies requirements for the evaluation of stent systems (vascular stents and delivery
systems) and requirements with respect to nomenclature, design attributes and information supplied
by the manufacturer, based upon current medical knowledge. Guidance for the development of in vitro
test methods is included in Annex D. This document is supplemental to ISO 14630, which specifies
general requirements for the performance of non-active surgical implants.
NOTE 1 Due to the variations in the design of implants covered by this document, and in some cases due to
the emergence of novel types of such implants, acceptable standardized in vitro tests and clinical results are not
always available. As further scientific and clinical data become available, appropriate revision of this document
will be necessary.
This document is applicable to vascular stents and vascular scaffolds (e.g. absorbable vascular
scaffolds) used to treat vascular stenoses or other vascular abnormalities or pathologies. Some of
the requirements are specific to endovascular treatment of arterial stenoses. Although uses of stent
systems other than treatment of arterial stenoses (e.g. venous stenting) are within the scope of this
document, comprehensive requirements and testing are not described for these uses. Similarly, specific
stent configurations (e.g. bifurcation stents) are within the scope, but comprehensive requirements and
testing are not described for these devices.
Stents used in combination with an endovascular prosthesis to complete the treatment of a lesion,
including bridging stents (e.g. stents placed in the renal arteries after deployment of a fenestrated
endovascular prosthesis), are within the scope of this document, but test methods are not described for
the combination. ISO 25539-1 also provides information relevant to the preclinical in vivo and clinical
evaluations of such stents.
Vascular stents that have surface modifications, such as drug and/or other coatings, are within the
scope of this document. Stents covered with materials that significantly modify the permeability of the
uncovered stent (e.g. by covering the stent-free-surface area) are within the scope of ISO 25539-1. The
stent design or intended use might dictate the need to address functional requirements identified in
both ISO 25539-1 and this document (e.g. stents used in combination with endovascular prostheses,
stents used to treat aortic aneurysms).
Balloons integral to the stent system are within the scope of this document. This document provides
requirements beyond the requirements of ISO 10555-4, which are specific to the use of balloons with
vascular stents.
This document is not applicable to procedures and devices used prior to the introduction of the vascular
stent, such as balloon angioplasty devices.
Tacking devices intended to spot treat post-angioplasty dissections, coil supporting devices, and flow
diverters are within the scope of this document, but comprehensive requirements and testing are not
described for these devices.
Although drug-eluting stents are within the scope of this document, this document is not comprehensive
with respect to the drug-eluting properties of these devices.
NOTE 2 Vascular device-drug combination products are within the scope of ISO 12417-1.
Although absorbable stents and stents with absorbable coatings are within the scope of this document,
this document is not comprehensive with respect to the absorbable properties of these devices.
NOTE 3 Absorbable implants are within the scope of ISO/TS 17137.
Although coated stents and coated stent systems are within the scope of this document, this document
is not comprehensive with respect to coatings.
NOTE 4 Some coating properties are within the scope of ISO 17327-1.
This document does not address the requirements for, and the evaluation of, viable tissues and nonviable
biologic materials used in the construction of vascular stents.

  • Standard
    124 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    121 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 8637-1:2020(Main)
Extracorporeal systems for blood purification - Part 1: Haemodialysers, haemodiafilters, haemofilters and haemoconcentrators (ISO 8637-1:2017)
EN ISO 8637-1:2020

EN-ISO 8637-1 specifies requirements for haemodialysers, haemodiafilters, haemofilters and haemoconcentrators, hereinafter collectively referred to as “the device”, for use in humans. This document does not apply to: - extracorporeal blood circuits; - plasmafilters; - haemoperfusion devices; - vascular access devices; - blood pumps; - pressure monitors for the extracorporeal blood circuit; - air detection devices; - systems to prepare, maintain or monitor dialysis fluid; - systems or equipment intended to perform haemodialysis, haemodiafiltration, haemofiltration or haemoconcentration; - reprocessing procedures and equipment.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day